• Progress in Superconductivity and Cryogenics
• /
• v.10 no.4
• /
• pp.33-37
• /
• 2008

The main objective of this study is to identify the pressure drop characteristics of coolant flow passages of 154kV/1GVA High Temperature Superconducting (HTS) power cable, experimentally. The passages were consisted of two parts, the one is the circular path with spiral ribs in the core to cool the cable conductor layer and the other is annular path with spirally corrugated outer wall to cool the shield layer. Thus the experiments to acquire the pressure drop data were performed with two types of circular spiral tubes and eight types of the concentric annuli in various range of Reynolds number. The pressure drops in the core tubes and the annuli were much higher than those in the tubes with smooth surface. Therefore, modified correlations to present the experimental results in each flow passage were suggested.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.3
• /
• pp.14-22
• /
• 2016

Pulping is a stage that can change fibrous raw materials into pumpable slurry. Recovered paper can be defibrated to individual fibers by shear stress generated by rotation of a rotor and water. Disintegration of recovered paper is more complicated than that of chemical pulp. When disintegration of recovered paper is poor, screening and cleaning efficiency will be worse and properties of paper will also be deteriorated. Therefore, pulping is an important treatment for improvement of availability of recovered paper and process runnability. In this study, degrees of disintegration of KOCC obtained from a linerboard mill was analyzed with a pilot-scale screen. Flake removal of KOCC slurry was performed by a pilot screen. Simple pumping action gave a positive effect on disintegration of KOCC. After pumping for 10 minutes, paper strength increased without the change of water retention value and fibrillation of KOCC slurry. This phenomena can be explained by modification of hornified surface of KOCC fibers by shear stress generated by pumping. Consequently, disintegration efficiency of KOCC can be enhanced by control of retention time at pulper or an agitation power at chests of papermaking process.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.11 no.6
• /
• pp.135-141
• /
• 2008

In this paper, a design method of broadband horn antenna having 3:1 bandwidth and multiple polarization characteristics is proposed. The feeding section of the antenna adopts quadruple-ridged waveguide type for broadband and multiple polarization characteristics of the antenna. By inserting a shorting bar in the cavity structure with a semi-sphere type back short, the return loss at the feeding section was minimized. A corrugated dielectric lens is designed for phase compensation and lens-surface matching at the antenna aperture, which improves the antenna beam pattern. The validity of the design method is verified by indicating the measured data of the antenna.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.6
• /
• pp.94-102
• /
• 2014

The physical and chemical properties of recycled fibers from mixed waste paper are more and more deteriorated because of unknown history of recycling times. In order to improve the mechanical properties of liner paper, the recycled fibers from wasted cotton clothes were used in papermaking process, and their applicabilities were evaluated in several points of fiber modification. Thus, two kinds of fiberizing methods from waste cotton clothes were considered by using rotary sandpaper and grinder mill. Finally, the rotary sandpaper method was relatively desirable in preserving longer fiber length and fibrillated fiber surface. The recycled cotton fibers by swelling treatment with NaOH and bleaching with reductive chemicals were mixed with OCC fibers, and the handsheets were prepared to basis weight of $80g/m^2$ and evaluated the mechanical properties of paper. The fibrous properties showed outstanding results in freeness and WRV improvements by alkali treatment and high brightness by reductive bleaching treatment. The physical and mechanical properties of sheet by mixing OCC fibers and recycled cotton fibers were also highly improved in tensile, burst strength and specially folding resistance.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.216-221
• /
• 2007

An experiment was carried out to investigate the effect of a coolant circuit arrangement on the heat transfer and air pressure drop of a fin-tube sensible heat exchanger with the corrugated fin surface. The air inlet temperature was set to $23^{\circ}C$,the relative humidity to 50% and the air inlet flow rate to 20, 22, $25m^3/min$, respectively. while the coolant temperature was set to $7^{\circ}C$, and the coolant mass flow rate to 10, 16, 22kg/min, respectively. Experiment showed that the exchanger having a diameter of 12.7mm with parallel circuit does better performance in sensible heat transfer and air pressure drop than those three of diameter of 12.7mm with a series circuit and that with diameter of 15.88mm with a parallel circuit.

• Journal of the Korean Society for Heat Treatment
• /
• v.16 no.4
• /
• pp.197-204
• /
• 2003

Honeycomb structure has been fabricated by brazing method using 0.1 wt%C and 1.0wt%C carbon steel core and STS304 stainless steel face sheet. Core shear strength ratio in W and L directions was 1:1.03 in 7 mm cell size, whereas 1:1.45 in 4 mm cell size. Flexural strength on face sheet was 166.4 MPa (0.1 wt%C, W direction), 171.1 MPa (0.1 wt%C, L direction), and 120.2 MPa (1.0 wt%C, W direction) in 7 mm cell size. And in 4mm cell size specimen, it was 169.2 MPa (0.1 wt%C, W direction), 224.2 MPa (0.1 wt%C, L direction). This means that flexural strength of 0.1 wt%C core material was higher than that of 1.0wt%C core material, which was contrary to expectation. SEM and EDS analysis represented that grain boundary diffusion had occurred in0.1 wt%C core, but no grain boundary diffusion in 1.0 wt%C core. And corrugated surface of 0.1 wt%C core was flat, whereas that of 1.0 wt%C core was not flat. As a result, contact area between two 1.0 wt%C cores was much less than that of 0.1 wt% cores, It is thought to be main reason for lower flexural strength of 1.0 wt%C core.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.6
• /
• pp.569-580
• /
• 2005

The present study investigates the convective heat/mass transfer characteristics in wavy ducts of a primary surface heat exchanger. The effects of duct aspect ratio and flow velocity on the heat/mass transfer are investigated. Local heat/mass transfer coefficients on the corrugated duct sidewall are determined using a naphthalene sublimation technique. The aspect ratios of the wavy duct are 7.3, 4.7 and 1.8 with the corrugation angle of $145\Omega$. The Reynolds numbers, based on the duct hydraulic diameter, vary from 300 to 3,000. The results show that at the low Re(Re $\leq$ 1000) the secondary vortices called Taylor-Gortler vortices perpendicular to the main flow direction are generated due to effect of duct curvature. By these secondary vortices, non-uniform heat/mass transfer coefficients distributions appear. As the aspect ratio decreases, the number of cells formed by secondary vortices are reduced and secondary vortices and comer vortices mix due to decreased aspect ratio at Re$\leq$1000. At Re >1000, the effects of corner vortices become stronger. The average Sh for the aspect ratio of 7.3 and 4.7 are almost same. But at the small aspect ratio of 1.8, the average Sh decreases due to decreased aspect ratio. More pumping power (pressure loss) is required for the larger aspect ratio due to the higher flow instability.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.4
• /
• pp.9-17
• /
• 2013

This paper describes an experimental program to investigate the shear behavior of insulated concrete sandwich panels (CSPs) with different types of GFRP shear connector. The study included testing of 13 insulated CSP specimens with two types of surface conditions for extruded polystyrene (XPS) insulation and various shapes of shear connectors. All specimens were loaded in direct shear by means of push-out and were consist of three concrete panels, two insulation layer and four rows of GFRP shear connectors. Load-relative slip between concrete panel and insulation response of CSP specimens has been established through push-out shear test. Test results indicate that the surface condition of insulation has a significant effect on the bond strength between concrete panel and insulation. The specimen used XPS foam with 10mm deep slot shows higher bond strength than those used XPS foam with meshed surface. Corrugated GFRP shear connectors show equivalent strength to grid GFRP shear connectors. Cross-sectional area and embedded length of shear connector have a notable effect on overall response and inplane shear strength of the CSP specimens.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.2
• /
• pp.24-31
• /
• 2001

As a novel method to improve strength properties of recycled test liner, Condebelt press drying system was introduced and adopted into Korea. New press drying treatment could enhance the surface and strength properties in accordance with the increase of sheet density. However, Condebelt drying can not increase the density of repeatedly recycled test liner as much as that of virgin UKP and at the same density condition, the strength of Condebelt press dried UKP is greater than that of press dried test liner. In order to increase the strength of test liner, two attempts were tried in this study. First, addition of polyelectrolytes, dry strength agent was investigated with a view to promote the fiber bonding potential of reclaimed corrugated container pulp. Second, blending effect of fines were analyzed in an aims of increasing density and strength of test liner. The results were as follows; Even in the case of test liner densified by Condebelt press dryer, addition of amphoteric PAM as a dry strength agent was effective in increasing strength properties and so the effect of dry strength agent on improving bonding potential of recycled OCC fiber could be confirmed. As an appropriate addition level of amphoteric PAM, below 1% based on dry pulp weight was suggested. Different from virgin UKP, density of recycled test liner can be increased by the blending of OCC fines and strength properties also can be improved. However, excessive blending of OCC fines could result in decreasing of density and serious weakening of test liner. The best blending ration of fines in test liner can be determined as about 30%. Taking into account the fines content in general OCC pulp as 50%, excessive 20% of fines were supposed to be fractionated and removed in order to achieve the best strength of Condebelt press dried test liner.

• Journal of the Korean Institute of Gas
• /
• v.1 no.1
• /
• pp.21-26
• /
• 1997

This paper presents the numerical results of six corrugation models which compute the stress behaviours and stress levels of the membrane structure under the hydrostatic pressure of cryogenic liquids and thermal loadings using a non -linear finite element analysis program. A three-dimensional analysis of various corrugation geometries was performed on the maximum mean normal stress distributions along the upper surface of the membrane sheet. Comparisons of the FEM results for various geometry models of the corrugation are presented, which shows that the corrugated configuration of the ring knot model can be effectively performed for the combined forces such as the hydrostatic pressure and thermal loading in comparison with the Technigaz type corrugation which has small comer and apex curvatures. The FEM results show that the ring knot corrugation can be used for the deepest depth, 180m of the LNG storage tank in comparison with other corrugation models.