• Journal of the Korean Chemical Society
• /
• v.37 no.11
• /
• pp.943-950
• /
• 1993

The determination of trace level germanium in 5.0 ${\times}\;10^{-2}$ M perchloric acid supporting electrolyte solution containing 8.0 ${\times}\;10^{-2}$ M catechol has been investigated by the square wave anodic stripping voltammetry. The optimum conditions in determination of germanium were as follows: deposition time; 120 sec, deposition potential; -0.9 volts vs. Ag/AgCl and frequency; 100 Hz. The determination of germanium was possible regardless of coexistent ion such as copper, lead and silicon. Calibration curve was shown a good linearlity in the range of 0.40 ppb to 2.0 ppm and the detection limit was 0.080 ppb. This method was useful for trace level germanium due to the short analysis time and higher sensitivity.

• Journal of Sensor Science and Technology
• /
• v.6 no.2
• /
• pp.155-162
• /
• 1997

Zinc oxide(ZnO) thin films were deposited on r-plane sapphires from a solution containing zinc acetate. The films were obtained in a hot wall reactor by the pyrolysis of an aerosol produced by an ultrasonic generator. The crystallinity, surface morphology and composition of the films have been studied using the x-ray diffraction method(XRD) scanning electron microscopy(SEM) and Auger electron spectroscopy (AES) respectively. The influences of the substrate temperature on the crystallinity of the films were studied. Strongly (110) oriented ZnO films were obtained at a substrate temperature of $350^{\circ}C$. The resistivity was increased to above $3{\times}10^{6}{\Omega}{\cdot}cm$ with copper doping and vapor oxidation.

• Carbon letters
• /
• v.10 no.2
• /
• pp.114-122
• /
• 2009

Crushed, depitted peach stones were impregnated activated with 50% $H_3PO_4$ followed by pyrolysis at $500^{\circ}C$. Two activated carbons were produced, one under its own evolved gases during pyrolysis, and the second conducted with air flow throughout the carbonization stage. Physicochemical properties were investigated by several procedures; carbon yield, ash content, elemental chemical analysis, TG/DTG and FTIR spectra. Porosity characteristics were determined by the conventional $N_2$ adsorption at 77 K, and data analyzed to get the major texture parameters of surface area and pore volume. Highly developed activated carbons were obtained, essentially microporous, with slight effect of air on the porous structure. Oxygen was observed to be markedly incorporated in the carbon matrix during the air treatment process. Cation exchange capacity towards Cu (II) and Cd (II) was tested in batch single ion experimental mode, which proved to be slow and a function of carbon dose, time and initial ion concentration. Copper was up taken more favorably than cadmium, under same conditions, and adsorption of both cations was remarkably enhanced as a consequence of the air treatment procedure. Sequestration of the metal ions was explained on basis of the combined effect of the oxygen functional groups and the phosphorous-containing compounds; both contributing to the total surface acidity character.

• Journal of Electrochemical Science and Technology
• /
• v.9 no.3
• /
• pp.195-201
• /
• 2018

To enhance the performance of cathodes at low temperatures, a Cu-coated cathode is prepared, and its electrochemical performance is examined by testing its use in a single cell. At $620^{\circ}C$ and a current density of $150mAcm^{-2}$, a single cell containing the Cu-coated cathode has a significantly higher voltage (0.87 V) during the initial operation than does that with an uncoated cathode (0.79 V). According to EIS analysis, the high voltage of the cell with the Cu-coated cathode is due to the dramatic decrease in the high-frequency resistance related to electrochemical reactions. From XPS analysis, it is confirmed that the Cu is initially in the form of $Cu_2O$ and is converted into CuO after 150 h of operation, without any change in the state of the Ni or Li. Therefore, the high initial cell voltage is confirmed to be due to $Cu_2O$. Because $Cu_2O$ is catalytically active toward $O_2$ adsorption and dissociation, $Cu_2O$ on a NiO cathode enhances cell performance and reduces cathode polarization. However, the cell with the Cu-coated cathode does not maintain its high voltage because $Cu_2O$ is oxidized to CuO, which demonstrates similar catalytic activity toward $O_2$ as NiO.

• Asian-Australasian Journal of Animal Sciences
• /
• v.25 no.3
• /
• pp.353-360
• /
• 2012

Mastitis is a highly morbid disease that requires detection at the subclinical stage. Tropical countries like India mainly depend on milch buffaloes for milk. The present study was conducted to investigate whether the trace minerals viz. copper (Cu), iron (Fe), zinc (Zn), cobalt (Co) and manganese (Mn) and enzyme activity of lactate dehydrogenase (LDH), alkaline phosphatase (ALP) and aspartate aminotransferase (AST) in riverine buffalo milk can be used as an indicator of subclinical mastitis (SCM) with the aim of developing suitable diagnostic kit for SCM. Trace elements and enzyme activity in milk were estimated with Atomic absorption Spectrophotometer, GBC 932 plus and biochemical methods, respectively. Somatic cell count (SCC) was done microscopically. The cultural examination revealed Gram positive bacteria as the most prevalent etiological agent. A statistically significant (p<0.01) increase in SCC, Fe, Zn, Co and LDH occurred in SCM milk containing gram positive bacterial agents only. ALP was found to be elevated in milk infected by both gram positive and negative bacteria. The percent sensitivity, specificity and accuracy, predictive values and likelihood ratios were calculated taking bacterial culture examination and $SCC\geq2{\times}10^5$ cells/ml of milk as the benchmark. Only ALP and Zn, the former being superior, were found to be suitable for diagnosis of SCM irrespective of etiological agents. LDH, Co and Fe can be introduced in the screening programs where Gram positive bacteria are omnipresent. It is recommended that both ALP and Zn be measured together in milk to diagnose buffalo SCM, irrespective of etiology.

• Progress in Medical Physics
• /
• v.27 no.4
• /
• pp.272-276
• /
• 2016

To investigate the optimum x-ray tube design for the dental radiology, factors affecting x-ray beam characteristics such as tungsten target thickness and anode angle were evaluated. Another goal of the study was to addresses the anode heel effect and off-axis spectra for different target angles. MCNPX has been utilized to simulate the diagnostic x-ray tube with the aim of predicting optimum target angle and angular distribution of x-ray intensity around the x-ray target. For simulation of x-ray spectra, MCNPX was run in photon and electron using default values for PHYS:P and PHYS:E cards to enable full electron and photon transport. The x-ray tube consists of an evacuated 1 mm alumina envelope containing a tungsten anode embedded in a copper part. The envelope is encased in lead shield with an opening window. MCNPX simulations were run for x-ray tube potentials of 70 kV. A monoenergetic electron source at the distance of 2 cm from the anode surface was considered. The electron beam diameter was 0.3 mm striking on the focal spot. In this work, the optimum thickness of tungsten target was $3{\mu}m$ for the 70 kV electron potential. To determine the angle with the highest photon intensity per initial electron striking on the target, the x-ray intensity per initial electron was calculated for different tungsten target angles. The optimum anode angle based only on x-ray beam flatness was 35 degree. It should be mentioned that there is a considerable trade-off between anode angle which determines the focal spot size and geometric penumbra. The optimized thickness of a target material was calculated to maximize the x-ray intensity produced from a tungsten target materials for a 70 keV electron energy. Our results also showed that the anode angle has an influencing effect on heel effect and beam intensity across the beam.

• Journal of Nutrition and Health
• /
• v.32 no.3
• /
• pp.230-238
• /
• 1999

The present study was conducted to investigate te effect of sea tangle and hypoglycemic agent(Metformin) on lipid peroxidation and antioxidants levels in normal and diabetic rats. Male Sprague-Dawley rats were fed AIN-76 based experimental diets containing 5% (w/w) cellulose or 15%(w/w) sea tangle for 3 weeks, and then rats of diabetic groups were rendered diabetic by intramuscular injection of streptozotocin(STZ, 45mg/kg BW). After induction of diabetes Metformin(350mg/kg BW) was given once a day using a feeding tube for 5 days. Blood glucose level in diabetic rats fed sea tangle was significantly lower than that of diabetic rats fed cellulose. Metformin feeding resulted in further lowering blood glucose. Plasma and liver microsomal levels of lipid peroxides were increased significantly in diabetic rats as compared to normal rats, and the plasma level tended to be decreased by sea tangle feeding. Plasma level of retinol was reduced by STZ treatment, but it was increased by Metformin feeding in diabetic rats fed sea tangle. The liver contents of retinyl plamitate were reduced in diabetic rats but recovered by sea tangle feeding to some extent. Liver contents of total vitamin A were increased significantly by sea tangle in diabetic rats. Although difference in either plasma or liver level of $\alpha$-tocopherol by diet and STZ treatment was not significant, $\alpha$-tocopherol levels were the highest in the group with simultaneous feeding of sea tangle and metformin. Liver contents of zinc and copper were not influenced by either STZ treatment or sea tangle feeding. The present study indicates that the lowering blood glucose level could be attained by simultaneous trial of sea tangle diet and hypoglycemic agent and the increased oxidative stress caused by STZz treatment could be relieved by sea tangle feeding.

• Journal of Nutrition and Health
• /
• v.32 no.3
• /
• pp.248-258
• /
• 1999

This study examined the effect of excess loading of calcium (Ca)and iron(Fe) on the bioavailability of minerals in both normal and Ca-and Fe-deficient rats. Three-week-old male rats were divided into four groups and fed experimental diets for six weeks, containing either normal (0.5%) or high(1.5%) Ca and normal (35ppm) or high (350ppm)Fe. Likewise, three-week-old male rats were first fed a Ca-and Fe-deficient diet for three weeks, and then fed one of four experimental diets for additional three weeks. In both normal and Ca-and Fe-deficient rats, ca contents of serum, liver, kidney and femur were not significantly affected by dietary Ca and Fe levels. Apparent Ca absorption(%) decreased in rats fed a high Ca diet regardless of dietary Fe levels. Magnesium(Mg) contents of serum, liver and femur significantly decreased in rats fed a high Ca diet. Fe contents of serum and liver significantly increased in rats fed a high-Fe diet, but decreased in rats fed a high Ca diet. Fe content of serum and liver significantly increased in rate fed a high-Fe diet, decreased in rats fed a high-Ca diet. Apparent Fe absorption increased in rats fed a high-Fe diet, and decreased in rats fed a high-Ca diet in Ca-and Fe-deficient rats, but dietary Ca did not seem to affect Fe absorption in normal rats. Phosphorus(P) contents of serum and femur were not significantly affected by dietary Ca and Fe levels in both normal and Ca-and Fe-deficient rats. Serum copper(Cu) decreased in rats fed a high-Fe diet, while serum zinc(Zn) decreased in rats fed a high-Ca diet in normal rats. Cu contents of liver, and Zn contents of serum and liver decreased in rats fed a high-Fe diet in Ca-and Fe-deficient rats. There results suggest that a dietary overload of Ca and Fe in both normal and Ca-and Fe-deficient rats may decrease mineral bioavailability leading to potential health problems.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.26 no.2
• /
• pp.137-145
• /
• 2000

Carcinogenesis is a multi-stage process that generally consists of at least three steps; initiation, promotion, and progression. If one of these carcinogenic steps were suppressed or delayed, the cancer could be prevented. Cancer chemoprevention is defined to be inhibition or reversal of the carcinogenic process by the specific chemical agents and is a novel approach to cancer management alternative to conventional chemotherapy. Chlorophylln(CHL), a water-soluble derivative of chlorophyll, containing sodium and copper, has been known to be strong antimutagen in several test systems, but its mechanism of antimutagenic action is unknown. In the present experiment, the possibility of CHL as chemopreventive drugs on 7,12-dimethylbenz[a]anthracene(DMBA)-induced hamster buccal pouch carcinogenesis was investigated by mutagenicity test, carcinogenicity test, and frequency or spectrum of H-ras mutations in the both of DMBA-induced and chlorophylln-pretreated-DMBA induced tumor by polymerase chain reaction and non-isotopic restriction fragment length polymorphism. The treatment of CHL reduced the yields and multiplicity of the 0.5% DMBA-induced tumor, 86% to 62.5% and $3.7{\pm}0.6$ to $1.4{\pm}0.3$, respectively. The occurrence of histidine revertant by $20{\mu}mole$ DMBA was inhibited 25.6 to 81.7% by 1 to $5{\mu}M$ CHL in a dose-dependent manner. The mutation rates of H-ras gene in DMBA-induced and CHL-pretreated-DMBA induced tumor were 96%, 94% of which the most mutations were in codon 12/13. These results suggest that CHL inhibits the carcinogenic action of DMBA by the formation of complex between CHL and DMBA or the inhibition of the activation of DMBA in vivo. But CHL did not affect the mutation rates or its spectrum in already formed tumor.

• Economic and Environmental Geology
• /
• v.29 no.1
• /
• pp.87-103
• /
• 1996

The purposes of this research are to investigate the pollution level of heavy metals due to the urbanization and industrialization in the satellite cities of Seoul, and to assess the chemical species and the sources of heavy metals in highly contaminated soils and dusts. Soil and dust samples were collected from the Uijeongbu and the Koyang cities, which are northern and the northwestern satellite cities of Seoul metropolitan city, respectively. Relatively high pH values($6.3{\sim}9.9$) were found in roadside soils compared with agricultural and forest soils. Difference in pH values of soils was not identified between before and after rainy seasons. In spite of no specific pollution sources in the above cities, the contents of Cu, Pb, and Zn in soils and dusts were much higher than the world average contents. The metal levels in dusts were higher than those in soils, but the metal concentration in dusts was significantly decreased after rainy season. Pollution index was high(> 1.0) in the areas of heavy traffic, industrial complex, and city centres. There is an appreciable proportion of total Zn in exchangeable/water-acid soluble fraction. Copper is predominantly associated with reducible and oxidizable phases, whereas Pb is largely in reducible association. It is concluded that the mobility and bioavailability of metals are high in the order of Zn >> Cu > Pb, on the basis of characteristic particle morphology and chemical composition, Pb-containing particles are originated probably from the automobile exhaust, particularly in heavy traffic areas. The metallic forms and iron-oxide associated forms of Cr, Ni, Cu, Zn, and Pb can be assessed as industrial origin.