• 한국인쇄학회지
• /
• 제20권1호
• /
• pp.45-53
• /
• 2002

The removal of chelated copper from anthraquinone dyes by cementation on powdered iron was studied. The removal of chelated copper was found to be a function of solution pH, amount of NTA and iron, and reaction temperature. In the presence of NTA, reaction rate of cementation was found to be strongly dependent on reaction temperature, solution pH, amount of NTA and amount of iron powder. These experimental results can be explained successfully by the distribution of complexed copper iron in solutions.

• 한국물환경학회지
• /
• 제22권4호
• /
• pp.626-631
• /
• 2006

The adsorption features of copper ion have been investigated by taking the barley residue which occurring from the beer production process as an adsorbent. Under the experimental conditions, adsorption equilibrium of copper ion was attained within 30 minutes after the adsorption started and the adsorption reaction was observed to be first order. As the temperature increased, the adsorbed amount of copper ion at equilibrium was also increased, which indicated that the adsorption reaction was endothermic. Based on the experimental results which obtained by varying the temperatures, several thermodynamic parameters for copper adsorption reaction were estimated. Regarding the electrokinetic behavior of barley residue, its electrokinetic potential was observed to be positive below pH 5 and turned into negative above this pH. In the pH range from 1.5 to 4, copper adsorption was found to be increased, which was well explained by the electrokinetic behavior of barley residue in the pH range. When nitrilotriacetic acid, which is a complexing agent, was coexisted with copper ion, equilibrium adsorption of copper ion was decreased and this was presumed to be due to the formation of metal complex. In addition, the adsorbed amount of copper ion was examined to be increased when $KNO_3$ was coexisted, however, it approached a saturated value above a certain concentration of $KNO_3$.

• 한국치위생학회지
• /
• 제10권3호
• /
• pp.531-540
• /
• 2010

Objectives : In this study, following the cavity restorations with low copper conventional alloy, high copper admixed one and high copper unicompositional one, which are used the most frequently in a clinical setting at the present, to experiment the time-dependent changes of strength, bubbles were examined. Besides, to examine the detrimental effects of mercury contained in dental amalgam, the amount of mercury release was evaluated. Methods : As dental amalgams which were used herein, [BESTALOY], [Hi-Aristaloy 21] and [Sybraloy] were selected for a low-copper conventional amalgam, a high-copper admixed one and a high-copper unicompositional one in the corresponding order. The formation of bubbles and the weight ratio of mercury release were evaluated using a field emission scanning electron microscope (FE-SEM). Thus, the following results were obtained: Results : 1. The time-dependent amount of mercury release reached a statistical significance in three types of alloys, which was shown in such a descending order as [BESTALOY], [Hi-Aristaloy 21] and [Sybraloy]. 2. A low-copper conventional type, BESTALOY is a cutting type and it was found to have an increased formation of fine bubbles. In the remaining two types, [Hi-Aristaloy 21] (a high-copper admixed alloy) and [Sybraloy] (a high-copper unicompositional alloy), the time-dependent changes in the formation of bubbles was negligible. Conclusions : Accordingly, this type of mercury release from amalgam alloy denotes the difference in the weight ratio of total constituents between after 24 hours and after two weeks. But further studies are warranted to examine the amount of mercury release which is detrimental to human bodies. Besides, a low-copper conventional alloy is a cutting type and it was characterized by the abundant formation of bubbles in a time-dependent manner. This implies that the strength of amalgam is impaired, which should be considered in selecting the appropriate amalgam alloy in a clinical setting.

• Tribology and Lubricants
• /
• 제20권6호
• /
• pp.299-305
• /
• 2004

The wear properties of clutch facing materials with two different copper amounts were evaluated against the fly-wheel materials used in clutch system, such as gray cast iron and spheroidal graphite cast iron. Sliding wear tests were carried out for four different combinations with these clutch facing materials and flywheel materials at different speeds and applied loads. Results showed that the clutch facing material contained a higher copper amount had the better wear resistance. And using the gray cast iron as the counter material, clutch facing material resulted in the much lower wear rate, regardless of the copper amount. It is obvious that the wear properties of clutch facing material are influenced from the thermal conductivities of the clutch facing material and the counter material.

• 자원리싸이클링
• /
• 제28권1호
• /
• pp.62-72
• /
• 2019

일반적으로, 황산동을 제조하기 위한 원료는 $H_2SO_4$ 및 Cu 금속이 사용된다. 본 연구는 폐산, 폐염화동 폐기물부터 전해 채취법을 이용하여 황산동을 제조하는 방법에 관한 것이다. 황산구리의 용도는 공업용, 도금용, 사료용, 농업용, 전자급 PCB 동도금에 사용된다. 종래의 황산동 제조법은 다량의 폐수 및 에너지 비용이 높은 문제점이 있다. 구리(Cu) 화합물 중에서 가장 사용이 많이 되는 황산동($CuSO_4$)의 제조 방법에 관한 연구로서, 공정 운전비가 적고, 폐수 발생이 적으며, 제조 공정이 간단하다. 양이온 맴브레인을 이용하여 Na, Ca, Mg, Al을 불순물로서 제거하기 쉽다. 또한 동시에 전해 채취 방법으로 고 순도 구리 분말을 회수 할 수 있었다. 회수 된 구리 분말을 사용하여 고 순도 황산동을 제조 할 수 있었다.

• KSTLE International Journal
• /
• 제2권1호
• /
• pp.22-28
• /
• 2001

A resin bonded copper-graphite brush was investigated to evaluate the characteristics electrical signal transmission through a sliding contact as a function of the relative amount of graphite and copper in the brush. Particular attention was given to the correlation between electrical signal fluctuation and tribological properties in an electrical sliding contact system. A ring-on-block type tribotester was used for this experiment and the ring was made from pure copper. Results showed that a copper-graphite brush at a particular composition range exhibited the most stable frictional behavior with a minimum voltage drop. The amount of voltage drop at the friction interface was affected by the surface roughness, transfer film formation at the friction interface, and the real area of contact. Microscopic observations and the surface analysis showed a good agreement with the results from this experiment. The results also indicated that the electrical signal flunctuation was directly associated with the oscillation of the coefficient of friction during sliding by nanoscale variation of contacts at the friction interface.

• 한국환경보건학회지
• /
• 제12권1호
• /
• pp.47-54
• /
• 1986

The purpose of the study is to determine the effects of sodium alginate on the suppression of organ accumulation of heavy metals were tested by mice. The seventy mice were divided into the control group and the experimental groups. The mice of cadmium group were subdivided into three groups by dose of 10 ppm cadmium group, adding 1% sodium alginate to the diets contaminated with 10 ppm cadmium group and adding 10% sodium alginate to the diets contaminated with 10 ppm cadmium group. The mice of copper group were subdivided into three groups by dose of 10 ppm copper group, adding 1% sodium alginate to the diets contaminated with 10 ppm copper group, and adding 10% sodium alginate to the diets contaminated with 10 ppm copper group. After the series of feeding of twenty-one days, the mice were killed and examined. Organs and feces were removed and analyzed for cadmium and copper amounts. The results obtained were as follows 1. As for average body weight gains, those of control group mice were the highest than heavy metal group and those of adding 10% sodium alginate to the diets contaminated with 10 ppm copper group the lowest. 2. The amount of cadmium accumulated in liver and kidney was higher than blood. The amount of cadmium in organs was higher in cadmium group than adding sodium alginate to the diets contaminated with cadmium group. 3. The amount of copper in liver was the highest, and that of copper in blood was the lowest. 4. The excretion of heavy metals was promotioned by adding 10% sodium alginate to the diets contaminated with 10 ppm heavy metal. ( P < 0.05 ).

• Korean Chemical Engineering Research
• /
• 제46권5호
• /
• pp.863-867
• /
• 2008

피치계 활성탄소섬유가 납사분해 잔사유를 개질하여 용융 방사하고, 산화, 탄화 및 스팀으로 활성화하여 제조되었다. 활성탄소섬유의 표면은 주석-팔라듐을 사용하여 단일 스텝에 의해 예민화 과정을 거쳤다. 예민화된 활성탄소섬유 표면에 무전해도금법을 사용하여 구리를 골고루 담지하였다. 도금시간을 증가시켜서 구리의 담지량을 변화시키고, BET, SEM, XRD 및 ICP를 이용하여 촉매 특성 변화에 미치는 영향을 관찰하였다. 도금시간에 따라 부가된 구리의 양은 증가하나, 기공부피와 비표면적은 감소하였다. 또한 반응 온도가 증가함에 따라 NO 제거 성능이 증가하였다. $300^{\circ}C$ 이상의 반응 온도에서 부가된 구리의 양이 증가하면 표면적의 감소와 구리 분산도의 감소 때문에 NO 제거 성능은 감소하는 결과를 얻었다.

• Environmental Sciences Bulletin of The Korean Environmental Sciences Society
• /
• 제1권2호
• /
• pp.157-166
• /
• 1997

The biosorption performances of copper were investigated by the immobilized biomass of nonliving marine brown algae Undaria pinnatifida by each of the Ca-alginate method(Ca-ALG), Ba-alginate method(Ba-ALG), polyethylene glycol method(PEG), and carrageenan method (CARR). The copper removal performance increased but the copper uptake decreased as the biomass amount was increased. However, the copper uptake by the immobilized biomass increased with increasing initial copper concentration. Among the immobilization methods, the copper uptake decreased in the following sequence: Ca-ALG > Ba-ALG > PEG > CARR. The pattern of copper uptake by the immobilized biomass fitted the Langmuir isotherm better than the Freundlich isotherm. Desorption of deposited copper with 0.05 ~0.5M HCI, resulted in no changes of the copper uptake capacity of the immobilized biomass by the immobilization methods except for PEG, through five subsequent biosorption/desorption cycles. There was no damage to the immobilized biomass which retained its macroscopic appearance in repeated copper uptake/elution cycles.

• Journal of Electrochemical Science and Technology
• /
• 제11권1호
• /
• pp.60-67
• /
• 2020

In this study, copper (II) oxide powder for electroplating was prepared by recovering CuCl₂ from NaClO₃ type etching wastes via recovered non-sintering two step chemical reaction. In case of alkali copper carbonate [mCuCo₃·nCu(OH)₂], first reaction product, CuCo₃ is produced more than Cu(OH)₂ when the reaction molar ratio of sodium carbonate is low, since m is larger than n. As the reaction molar ratio of sodium carbonate increased, m is larger than n and Cu(OH)₂ was produced more than CuCO₃. In the case of m has same values as n, the optimum reaction mole ratio was 1.44 at the reaction temperature of 80℃ based on the theoretical copper content of 57.5 wt. %. The optimum amount of sodium hydroxide was 120 g at 80℃ for production of copper (II) oxide prepared by using basic copper carbonate product of first reaction. At this time, the yield of copper (II) oxide was 96.6 wt.%. Also, the chloride ion concentration was 9.7 mg/L. The properties of produced copper (II) oxide such as mean particle size, dissolution time for sulfuric acid, and repose angle were 19.5 mm, 64 second, and 34.8°, respectively. As a result of the hole filling test, it was found that the copper oxide (II) prepared with 120 g of sodium hydroxide, the optimum amount of basic hydroxide for copper carbonate, has a hole filling of 11.0 mm, which satisfies the general hole filling management range of 15 mm or less.