• 한국초전도학회:학술대회논문집
• /
• v.11
• /
• pp.25-25
• /
• 2001

• Progress in Superconductivity
• /
• v.4 no.2
• /
• pp.99-103
• /
• 2003

We studied the nonequilibrium superconductivity due to tunnel injection of polaronic quasiparticle (QP) from organic photoconductor. The transport properties of an organic copper (II) phthalocyanine (Cu -Pc)/d-wave superconductor were investigated in dark and under ultraviolet (UV) radiation for performance of a novel $high -T_{c}$ superconducting three terminal device. We observed that the injection of polaronic QP from the organic Cu -Pc film into the $Bi_2$S $r_2$$CaCuO_{8+{\delta}}$ film generated a substantially larger nonequilibrium effect as compared to the normal QP injection current. We could increase the current gain by UV excitation of the organic photoconductor injector. The tunneling spectroscopy of a Cu -Pc/BSCCO junction exhibited a small enhancement of the zero bias conductance peak under the W excitation. The above phenomena are of importance in developing optically controlled three terminal superconducting device.e.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.1
• /
• pp.41-44
• /
• 2014

Emission properties of the organic light-emitting diodes were investigated with the use of a hole-injection layer of copper(II)-phthalocyanine (CuPc). The manufactured device structure is indium-tin-oxide (ITO) (180 nm)/CuPc (0~50 nm)/N,N'-Bis(3-methylphenyl)-N,N'-diphenylbenzidine (TPD) (40 nm)/tris-(8-hydroxyquinoline) aluminum (III) ($Alq_3$) (60 nm)/Al(100 nm). We investigated the luminescence properties of $Alq_3$ which is affected by the CuPc hole-injection layer. Also, we studied the influence of light-emission properties in the structure of an ITO/CuPc/TPD/$Alq_3$/Al device depending on the several thicknesses of CuPc (0~50 nm) layer. As a result, it was found that the hole injection occurs smoothly in the device with 20 nm thick CuPc layer, and the properties become significantly worse in the device with a CuPc layer thickness higher than 40 nm. We studied the topography and external quantum efficiency depending on the layer thickness of CuPc. Also, we analyzed the electroluminescent characteristics in the low and high-voltage range.

• Journal of the Korean Chemical Society
• /
• v.43 no.1
• /
• pp.58-68
• /
• 1999

The phthalocyanine(Pc) film can not be prepared by LB method because it is insoluble in organic solvents. In order to increase its solubility, two kinds of copper phthalocyanine derivatives (CuPc$(COOH)_2$ and CuPc$(COOH)_4$) were synthesized and their monolayers were prepared by LB method. It is found from the surface pressure-area curves that the LB monolayer film of CuPc$(COOH)_2$ have more ordered structure than that of CuPc$(COOH)_4$. In the photocurrent characteristic the value Of CuPc$(COOH)_2$ was superior to that of CuPc $(COOH)_4$. Therefore, it is found that the charge generation efficiency for phthalocyanines have influenced on its ordered structure as the functional groups.

• 한국초전도학회:학술대회논문집
• /
• v.12
• /
• pp.17-17
• /
• 2002

• Proceedings of the Korean Vacuum Society Conference
• /
• 2008.08a
• /
• pp.120-120
• /
• 2008

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.73-73
• /
• 2011

We will report a few methods to improve the efficiency and stability in small molecule based organic solar cells, including the formation of bulk heterojunctions (BHJs) through alternative thermal deposition (ATD), the use of a micro-cavity structure and interface modifications. By ATD which is a simple modification of conventional thermal evaporation, the thicknesses of alternative donor and acceptor layers were precisely controlled down to 0.1 nm, which is critical to form BHJs. The formation of a BHJ in copper(II) phthalocyanine (CuPc) and fullerene (C60) systems was confirmed by AFM, GISAXS and absorption measurements. From analysis of the data, we found that the CuPc|C60 films fabricated by ATD were composed of the nanometer sized disk shaped CuPc nano grains and aggregated C60, which explains the phase separation of CuPc and C60. On the other hand, the co-deposited CuPc:C60 films did not show the existence of separated CuPc nano grains in the CuPc:C60 matrix. The OPV cells fabricated using the ATD method showed significantly enhanced power conversion efficiency compared to the co-deposited OPV cells under a same composition [1]. We will also present by numerical simulation that adoption of microcavity structure in the planar heterojunction can improve the short circuit current in single and tandem OSCs [2]. Interface modifications also allowed us to achieve high efficiency and high stability OSCs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.230-230
• /
• 2010

유기물 반도체 화합물인 Cu-Pc(copper(II)-phthalocyanine)는 우수한 전기적 광학적 특성을 가지며, OLED, MISFET등 소자로서의 활용도가 높다. Cu-Pc 화합물은 $\alpha$-phase, $\beta$-phase, $\gamma$-phase를 포함하는 여러 가지 다결정 polymer로 존재할 수 있다. 가장 잘 알려진 구조로는 열적으로 준안정적인 $\alpha$-phase와 열적으로 안정적인 $\beta$-phase가 있다. Cu-Pc 박막의 구조 및 흡수 특성과 전기적 특성에 대한 기술이 확실히 규명되지 않아 본 연구에서는 두께와 열처리 조건에 따른 결정성 및 방향성을 조사하기 위하여 $\alpha$-phase와 $\beta$-phase의 phase transition 현상 및 전기적 광학적 특성을 규명 하고자 한다. 진공증착 방법 중 하나인 PVD 방법의 thermal evaporation deposition을 이용하여 glass, ITO 기판위에 두께와 열처리에 따른 전기적?광학적 특성을 연구하였다. Cu-Pc 박막의 성장두께는 5nm~50nm 이내로 fluxmeter 및 thickness monitor를 이용하여 제어하였다. 5nm~50nm의 두께에 따른 기판온도를 $200^{\circ}C$로 고정하여 전열 처리 및 후열 처리하여 온도에 따른 박막을 성장한 후, 결정 구조 및 특성 변화와 phase transition 분석하였다. 제작된 Cu-Pc의 박막은 $\alpha$-phase와 $\beta$-phase로 구분할 수 있으며, 열처리에 따른 phase transition 현상이 뚜렷함을 알 수 있다. XRD(X-ray diffraction)를 통하여 박막에 대한 결정 구조 분석 및 FE-SEM(field emission scanning electron microscopy)와 AFM(atomic force microscopy)을 이용하여 Cu-Pc 박막의 구조적 결정성과 방향성 등, 표면 상태와 형상구조에 대해 표면의 특성을 측정하며, 광 흡수도(UV-visible absorption spectra)을 이용하여 phase transition 현상에 따른 I-V 특성을 비교분석 하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.254-254
• /
• 2010

Cu-Pc(copper(II)-phthalocyanine)는 박막의 형성과정에서 열처리 방식과 온도에 따라 박막의 구조가 변하며, 구조로는 열적으로 준 안정적인 $\alpha$-phase와 열적으로 안정적인 $\beta$-phase가 있다. 본 연구에서는 Cu-Pc 박막의 열적으로 안정적인 $\beta$-phase 구조에 대해 온도 조건 변화에 따른 표면 결정 성장의 특성을 연구하고자 한다. 진공증착 방법 중 하나인 thermal evaporation deposition을 이용하여 glass 기판위에 전열 처리 및 후열 처리에 대해 온도 조건 변화에 따른 $\beta$-phase type의 표면 결정 특성을 연구하였다. Cu-Pc 박막의 성장두께는 50nm 일정한 두께로 fluxmeter 및 thickness monitor를 이용하여 제어하였다. 50nm의 두께에 따른 기판온도를 $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$로 전열 처리한 후 각각 전열 처리한 기판온도에 대해 1hour, 2hour, 3hour 후열 처리하여 온도 조건에 따른 박막을 성장한 후, $\beta$-phase type에 대한 결정 구조 및 표면 특성 변화를 분석하였다. 제작된 Cu-Pc의 박막은 $\beta$-phase type으로, 열처리에 따른 $\beta$-phase transition 현상을 연구하였다. XRD(X-ray diffraction)를 통하여 박막에 대한 결정 구조 분석 및 FE-SEM(field emission scanning electron microscopy)을 이용하여 Cu-Pc 박막의 구조적 결정성과 방향성 등, 표면 상태와 형상구조에 대해 표면의 특성을 분석하며, 광 흡수도(UV-visible absorption spectra)을 이용하여 온도 조건에 따른 투과/흡수 현상을 비교분석하였다.