• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.1
• /
• pp.116-123
• /
• 2003

In this paper, interleaved boost converter is applied as a pre-regulator in switched mode power supply. The pre-regulator plays a role to improve power factor. Interleaved Boost Power Factor Corrector(IBPFC) can reduce input current ripple as a single voltage control loop only without inner current loop, because input current is divided each 50% by two switching devices. Each converter cell is also operated in discontinuous current mode and inductor current of each converter is discontinuous. Total input current which is composed by each converter cell is continuous current. Thus, IBPFC is able to improve input current ripple. IBPFC operating in discontinuous current mode can be classified as six modes from switching state and be carried out state space averaging small signal modeling. A control transfer function is obtained according to the modeling. Single voltage control loop is also constructed by the control transfer function. From experimental result, improvement of power factor and input current ripple are verified.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.12
• /
• pp.2379-2384
• /
• 2009

In this paper, based on MATLAB which has characteristic that is simply applied to control algorithm and source modeling, photovoltaic modeling is implemented. Photovoltaic modeling is similarly performed PV array and simulated. Also, in order to output maximum power of PV, MPPT control is simulated. Moreover, simulation of converter is performed by means of PLECS (Piece wise Linear Electrical Simulation) which is easily made schematic of power electronics. Also, we compare simulation results and Sharp PV module and Suntech PV module. Finally, informative simulation of PV generation system is provided.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.3
• /
• pp.211-216
• /
• 2013

A wind generator system model includes wind model, rotor dynamics, synchronous generator, power converter, distribution line and infinite bus. This paper investigates the low-Voltage Ride-Through capability of PMSG wind turbine in a variable speed. The drive train of a wind turbine on 2-mass modeling can observe the shaft torsional vibration when the low-voltage occur. To reduce the torsional vibration when the low-voltage occur, this paper designs suppression control algorithm of the torsional vibration and implements simulation. The simulation based on MATLAB/SIMULINK has validated at the transient state of the PMSG and an experiment using 3kW simulator has validated the LVRT control.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.6
• /
• pp.369-374
• /
• 2016

This paper presents a design procedure of an integrated inductor with a magnetic core for power converters. This procedure considerably reduces design time and effort. The proposed design procedure is verified by the development of an inductor model dedicated to the monolithic integration of DC-DC converters for portable applications. The numerical simulation based on the FEM (finite elements method) shows that 3D modeling of the integrated inductor allows better estimation of the electrical parameters of the desired inductor. The optimization of the electrical parameter values is based on the numerical analysis of the influence of the geometric parameters on the electrical characteristics of the inductor. Using the VHDL-AMS language, implementation of the integrated inductor in a micro Buck converter demonstrate that simulation results present a very promising approach for the monolithic integration of DC-DC converters.

• Journal of information and communication convergence engineering
• /
• v.6 no.4
• /
• pp.417-420
• /
• 2008

Solar electric systems have very little impact on environment, making them one of the cleanest power-generating technologies available. While they are operating, PV systems produce no air pollution, hazardous waste, or noise, and they require no transportable fuels. In PV system design, the selection and proper installation of appropriately-sized components directly affect system reliability, lifetime, and initial cost. In this research, we have studied the PWM(Pulse Width Modulation) signals. I proposed an efficient photovoltaic power interface circuit incorporated with a DC-DC converter and a sine-pwm control method full-bridge inverter. In grid-connected solar power systems, the DC-DC converter operates at high switching frequency to make the output current a sine wave, whereas the full-bridge inverter operates at low switching frequency which is determined by the ac frequency. Thus, it can reduce the switching losses incurred by the full-bridge inverter. Full-bridge converter is controlled by using microprocessor control method, and its operation is verified through computer aided simulations.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.8
• /
• pp.828-835
• /
• 1990

A new state feedback control scheme is proposed to improve the stability and dynamic performances of the series resonant converter (SRC). The proposed scheme can be easily implemented without speed limitation. Design parameter of the proposed control is the ratio of the state feedback gains. A closed loop dynamic modeling for the SRC with the proposed control law is derived. Parametric curves which can be used to select the design parameter in the control system are presented. The experimental results show that the excellent dynamic performance of the converter can be obtained by properly selecting the design parameter. The results are further compared with both the theoretical analysis and the frequency control.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.5
• /
• pp.490-498
• /
• 2002

In this paper, a design method of LCL filter at the AC input side of a voltage source PWM converter is proposed. Effective method to prevent pollution of the utility caused by high frequency current ripple is to use a AC input LCL filter, The C elements in the filter provide a low impedance path for the high frequency component, preventing them from entering the utility. The resistors In series with the capacitors are used for damping the resonance in the filter The design examples are shown and the validity of the proposed design method is verified through the PSIM simulation.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.538-541
• /
• 2002

Dynamic analysis and compensation design for an asymmetrical half bridge do-dc converter are presented. A small-signal model is developed using the averaging method. Based on the proposed small-signal average model, the open loop transfer functions of the power stage were obtained and used for the compensation design. All theoretical predictions are validated by experiments on a prototype converter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.171-177
• /
• 2004

Piezoelectric transformer(PZT) can be used advantageously in high output voltage power supply. Recently, it also can be used in AC/DC Converter for miniaturizing size nd lightening weight. The modeling of PZT was performed by the calculation method through the physical and electrical constants of the material. The attributes of PZT were derived by an approximate analysis for output voltage gain, and resonant frequency. The proposed method is verified by computer simulation and experiment.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.148-151
• /
• 1997

Pspice is not offered a library of mechanical factor like DC Motor, Induction Motor which is needed in Power Electronics field. Therefore, Induction Motor was made library by Equibalent circuit in this study. This model is applied in Voltage-Type inverter and is investigated its characteristics. IGBT is tested by two methods of Macro and Micro Modeling as semiconductor. PWM signal is used of pulse signal. Voltage and current, speed was simulated for assurance of model.