• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.98-100
• /
• 2003

The microwave dielectric properties and microstructure of the $0.7Mg_4Ta_2O_9-0.3CaTiO_3$ ceramics were investigated. All sample of the $0.7Mg_4Ta_2O_9-0.3CaTiO_3$ ceramics were prepared by conventional mixed oxide method. The sintering temperature was $1375^{\circ}C{\sim}1450^{\circ}C$. The structural properties of the $0.7Mg_4Ta_2O_9-0.3CaTiO_3$ ceramics were investigated by X-ray diffractormeter. According to the X-ray diffraction patterns of the $0.7Mg_4Ta_2O_9-0.3CaTiO_3$ ceramics, the major phase of the hexagonal $Mg_4Ta_2O_9$ were presented. In the case of the $0.7Mg_4Ta_2O_9-0.3CaTiO_3$ ceramics sintered at $1425^{\circ}C$, density, dielectric constant, quality factor were $5.799g/cm^2$, 23.26, 40,054 GHz, respectively.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.352-355
• /
• 2006

As the stainless steel has good corrosion resistance, mechanical property and ease of manufacture, it has been studied as the candidate material of metallic bipolar plate for automotive PIMFC. But, metal is dissolved under fuel cell operating conditions Dissolved ions contaminate a membrane electrode assembly (MEA) and, decrease the fuel cell performance. In addition, metal oxide formation on the surface of stainless steel increases the contact resistance in the fuel cell. These problems have been acted as an obstacle in the application of stainless steel to bipolar plate. Therefore, many kinds of coating technologies have been examined in order to solve these problems. In this study, stainless steel was coated in order to achieve high conductivity and corrosion resistance by several methods. Contact resistance was measured by using a tensile tester and impedance analyzer Corrosion characteristics of coated stainless steel were examined by Tafel-extrapolation method from the polarization curves in a solution simulating the anodic and cathodic environment of PEMFC. Fuel cell performance was also evaluated by single cell test. We tested various coated metal bipolar plate and conventional and graphite were also tested as comparative samples. In the result, coated stainless steel bipolar plate exhibited better cell performance than graphite to bipolar plate.

• Ocean and Polar Research
• /
• 제32권2호
• /
• pp.157-164
• /
• 2010

A marine alga, Spirulina maxima, was extracted under high pressure and low temperature conditions at 500 MPa and $60^{\circ}C$ for 5 and 10 min. A high pressure of 500 MPa was applied to improve process yields because of low temperature extraction. This method resulted in highest higher extraction yield of 26.1% (w/w) in comparison to those results obtained from conventional extraction methods which produced a yield of 17.6% (w/w) from water. The extracts from this process also showed 19% of low cytotoxicity against human normal fibroblast cells in adding 1.0 mg/ml of the highest concentration. The crude extract significantly reduced the production of Prostaglandin $E_2$ ($PGE_2$) from CCD-986sk cells and increased nitric oxide production by macrophages. These higher activities of enhancing skin immune functions were found to have high antioxidant extract properties, like a 98% increase in DPPH radical scavenging activity. The extracts from the high pressure process showed a higher elution of active components than other processes and generated new compounds based on HPLC analysis. This clearly indicates that the extracts from high pressure and low temperature conditions have higher skin immune activation properties that have not been previously reported.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.682-685
• /
• 2002

The $0.96MgTiO_3-0.04SrTiO_3$ ceramics with $B_2O_3$(10wt%) were prepared by the conventional mixed oxide method. The structural properties were investigated with sintering temperature by XRD. According to the X-ray diffraction pattern of the $0.96MgTiO_3-0.04SrTiO_3$ ceramics with $B_2O_3$(10wt%), the ilmenite $MgTiO_3$ and perovskite $SrTiO_3$ structures were coexisted and secondary phase of the $MgTi_2O_5$ were appeared. In the case of $0.96MgTiO_3-0.04SrTiO_3+B_2O_3$(10wt%) ceramics sintered $1225^{\circ}C$, dielectric constant, quality factor and temperature coefficient of resonant frequency were 19.82, 62,735GHz, $-2.983ppm/^{\circ}C$, respectively.

• The Journal of Advanced Prosthodontics
• /
• 제10권3호
• /
• pp.205-210
• /
• 2018

PURPOSE. The purpose of this study was to evaluate the efficiency of a gas-phase fluorination method under different fluorination periods through using two resin cements. MATERIALS AND METHODS. 84 zirconia specimens in dimensions of $5mm{\times}5mm{\times}2mm$ were prepared and surface treated with $50{\mu}m$ aluminum oxide particles or gas phase fluorination for 2 min, 5 min, or 10 min. One specimen in each group was surface analyzed under scanning electron microscope. The remaining specimens were bonded to composite cylinders in dimensions of 2 mm diameter and 3 mm high with Panavia SA Plus or Variolink N. Then, the specimens were stored in $37^{\circ}C$ distilled water for 24 hours and shear bond strength test was applied at a speed of 1 mm/min. RESULTS. The highest shear bond strength values were observed in the samples fluorinated for 5 minutes and cemented with Panavia SA Plus. Variolink N did not elicit any statistical differences between surface treatments. Panavia SA Plus resin cement and Variolink N resin cements featured statistically significant difference in shear bond strength values only in the case of 5 minutes of fluorination treatment. CONCLUSION. According to the results of this study, application of 5 minutes of fluorination with 10-methacryloyloxydecyl dihydrogen phosphate monomer (MDP) containing Panavia SA Plus resin cement increased the resin bond strength of zirconia. Fluorination of the zirconia surface using conventional resin cement, Variolink N, did not lead to an increase in bond strength.

• 한국인터넷방송통신학회논문지
• /
• 제10권5호
• /
• pp.1-5
• /
• 2010

본 논문은 열연 공정을 거친 철강 강판에 형성된 산화철 층, 즉 scale 층의 두께를 유전체 렌즈 안테나를 이용하여 측정하는 방법을 소개하였다. 유전체 렌즈 안테나는 X 밴드 대역에서 주파수에 독립적인 특성을 가지며, 혼 안테나에서 방사되는 구면파를 초점이 형성되는 평면에 평면파를 형성하는 역할을 한다. 이러한 동작원리를 이용하여 철강 강판에 형성된 scale 층에 완전 도체와 유전체로 형성된 two-layer 구조에 직각 입사하는 평면파의 이론적 해석이 적용될 수 있다. Scale의 두께를 도출해 내는 과정에서 유전체 렌즈의 영향을 최소화하기 위한 calibration 과정이 삽입되었으며, 이로 인한 반사 계수 위상의 오차가 발생하였다. 이러한 위상 오차에 의한 scale 두께의 오차를 줄이기 위하여, 수치적으로 regression 방법을 사용하였으며, 기존의 iteration 방법과 비교하여, 주기적으로 얻어지는 두께의 값이 아닌 단일 두께 값을 얻어낼 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.363-366
• /
• 2004

The structural and microwave dielectric properties of $0.7Mg_4Ta_2O_9-0.3SrTiO_3$ ceramics with sintering temperature were investigated. All the sample of the $0.7Mg_4Ta_2O_9-0.3SrTiO_3$ ceramics were prepared by conventional mixed oxide method and sintered at $1425^{\circ}C{\sim}1500^{\circ}C$. According to XRD Patterns, hexagonal $Mg_4Ta_2O_9$ phase and cubic $SrTiO_3$ Phase were coexisted. The porosity of $0.7Mg_4Ta_2O_9-0.3SrTiO_3$ ceramics were reduced with increasing sintering temperature. In the case of $0.7Mg_4Ta_2O_9-0.3SrTiO_3$ ceramics sintered at $1475^{\circ}C$, dielectric constant, quality factor and temperature coefficient of resonant frequency were 14.51, 82,596GHz and $-3.14ppm/^{\circ}C$, respectively.

• 한국전기전자재료학회논문지
• /
• 제17권8호
• /
• pp.840-845
• /
• 2004

The microstructure and microwave dielectric properties of $(1-x){Mg}_4{Ta}_2{O}_9-xTi{O}_2(x=0\sim0.9)$ ceramics were investigated. The specimens were prepared by the conventional mixed oxide method with sintering temperature of 140$0^{\circ}C$∼150$0^{\circ}C$. To improve the quality factor and the temperature coefficient of resonant frequency,$ Ti{O}_2(\varepsilon\Gamma=100, Q\times f_\Gamma=40,000 GHz,\ta_f= +450 ppm\diagup^{\circ}C $ was added in ${Mg}_4{Ta}_2{O}_9$ceramics. The dielectric and structural properties were investigated. According to the XRD patterns, $(1-x){Mg}_4{Ta}_2{O}_9-xTi{O}_2(x=0\sim0.9)$ ceramics had the ${Mg}_4{Ta}_2{O}_9$ phase(hexagonal) and ${MgTi}_2{O}_5$phase(orthorhombic). The dielectric constant($\varepsilon_r$). quality($Qtimes{f}_r$${\tau}_f$) of the $(1-x){Mg}_4{Ta}_2{O}_9-xTi{O}_2(x=0\sim0.9)$ ceramics were 8.12∼18.59, 18,750∼186,410 GHz and －36.02∼＋3.46 ppm/$^{\circ}C$, respectively.

• 한국전기전자재료학회논문지
• /
• 제25권7호
• /
• pp.506-510
• /
• 2012

In this study, lead-free $(Na_{0.465}K_{0.465}Bi_{0.07})(Nb_{0.93}Ti_{0.07})O_3-0.08MnO_2$ ceramics were fabricated by conventional mixed oxide method. Structural and electrical properties of lead-free $(Na_{0.465}K_{0.465}Bi_{0.07})(Nb_{0.93}Ti_{0.07})O_3-0.08MnO_2$ ceramics with the variation of sintering temperature were investigated. As results of x-ray diffraction analysis, all specimens showed a typical polycrystalline perovskite structure without presence of the second phase. Sintered density increased with an increases of sintering temperature and the specimen sintered at $1,020^{\circ}C$ showed the maximum value of 4.5 $g/cm^3$. The average grain size of the $(Na_{0.465}K_{0.465}Bi_{0.07})(Nb_{0.93}Ti_{0.07})O_3-0.08MnO_2$ specimen sintered at $1,020^{\circ}C$ is about 0.83 ${\mu}m$. Electromechanical coupling factor, relative dielectric constant and dielectric loss of $(Na_{0.465}K_{0.465}Bi_{0.07})(Nb_{0.93}Ti_{0.07})O_3-0.08MnO_2$ specimens sintered at $1,020^{\circ}C$ were 0.252, 741 and 0.043% respectively.

• 한국전기전자재료학회논문지
• /
• 제26권2호
• /
• pp.104-108
• /
• 2013

In this paper, the $0.95(Na_{0.5}K_{0.5})_{0.04}[(Nb_{0.8}Ta_{0.20})_{0.994}Co_{0.015}]O_3$(abbreviated as NKNT) + $0.05KNbO_3$ lead-free piezoelectric ceramics were synthesized by the conventional mixed oxide method route with normal sintering. And also, the effects of calcination temperature on the microstructure, dielectric properties, and piezoelectric properties were investigated. A polymorphic phase transition(PPT) between orthorhombic and tetragonal phases was observed in specimens calcined at $810^{\circ}C{\sim}850^{\circ}C$. The ceramics calcined at $830^{\circ}C$ showed excellent piezoelectric properties: $d_{33}$= 179 pC/N, $k_p$= 0.384, $Q_m$= 79.73). These results indicate that the ceramic is a promising candidate material for lead-free piezoelectric ceramics.