• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.32-38
• /
• 2004

This study was performed to investigate the behavior of liquid and vapor phase of fuel mixtures with different piston cavity diameters in a optically accessible engine. The conventional engine was modified as Central Injected DI gasoline engine with swirl motion. Two dimensional spray fluorescence images of liquid and vapor phase were acquired to analyze spray behavior and fuel distribution inside of cylinder using exciplex fluorescence method. Piston cavity geometries were set by Type S, M and L. The results obtained are as follows. In the spray formation after SOI, the cone angle and width of the spray were decreased at late injection timing. With a fuel injection timing of BTDC $180^{\circ}C$, fuel was not greatly affected in a piston cavity but generally distributed as homogeneous mixture in the cylinder. With a fuel injection timings of BTDC $90{\circ}C$ and $60^{\circ}C$, fuel mixture was widely distributed in near the cavity center. As a injection timing was late in the compression stroke, residual width of fuel mixture was narrow in proportion to piston cavity.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.4
• /
• pp.85-97
• /
• 1999

For a deltaic clay in the mouth of the Nakdong river, OCR was investigated through methods using the results of field measurement, laboratory and field soil tests. As a result, OCRs were obtained around the range of 0.95 to 1.20 by analysis of field measurements, although they were estimated around the values of 0.4 to 0.7 by the results of conventional consolidation tests for the clay. From the dissipation test it was found out that the excess pore pressures scarcely existed in the clay deposit and then the soil was not in the underconsolidated condition. And the OCRs obtained through methods of Mayne(1991) and Cao et al(1996) using the piezocone test and of Mayne & Kemper(1988) using the cone penetration test were in good agreement with those of field measurement.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.8C
• /
• pp.1142-1148
• /
• 2004

A binaural filtering method using HRTF DB is generally used to make the headphone-based 3D sound. But it can make some confusion between front and back directions or between up and down directions due to the non-individual HRTF depending on each listener. To reduce the confusion of sound image localization, we propose a new method to boost the spectral cue by modifying HRTF spectra with spectrum difference between front and back directions. Informal listening tests show that the proposed method improves the front-back sound localization characteristics much better than the conventional methods

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.2
• /
• pp.245-256
• /
• 2014

I-core sandwich panel that has been used more widely is assembled using high power $CO_2$ laser welding. Kim et al. (2013) proposed a circular cone type heat source model for the T-joint laser welding between face plate and core. It can cover the negative defocus which is commonly adopted in T-joint laser welding to provide deeper penetration. In part I, a volumetric heat source model is proposed and it is verified thorough a comparison of melting zone on the cross section with experiment results. The proposed model can be used for heat transfer analysis and thermal elasto-plastic analysis to predict welding deformation that occurs during laser welding. In terms of computational time, since the thermal elasto-plastic analysis using 3D solid elements is quite time consuming, shell element model with multi-layers have been employed instead. However, the conventional layered approach is not appropriate for the application of heat load at T-Joint. This paper, Part II, suggests a new method to arrange different number of layers for face plate and core in order to impose heat load only to the face plate.

• The Journal of the Korean dental association
• /
• v.50 no.4
• /
• pp.196-202
• /
• 2012

Radiographic diagnosis of periapical lesions is based on many factors, including anatomical limitations such as thickness of the cortical bone; positioning of the apical abscess to the cortical bone; and is complicated by proximity to other anatomical structures and neighboring teeth. With conventional radiographs, these structures are often superimposed. Dental CBCT with its associated geometric accuracy offers accurate visualizations of the complex relationships and boundaries between teeth, related anatomical features, and their associated pathology. Its images also provide us internal tooth morphology, periodontal ligament space, the presence or absence of periapicl lesions in association wi th critical anatomical structures and maxillary sinus involement. Using 3 D imaging makes it easier for clinicians to detect, diagnosis, and develop highly effective treatment plans. Now, 4 cases of periapical and periodontal pathosis with CBCT images are to be presented including periapical abscess, furcation involvement, periapical pathosis involving maxillary sinus, and osteomyelitis. CBCT analyze specific area of interest and provides the highly detailed anatomical information. It also facilitates earlier and more accurate diagnosis, and treatment planning decisions and more predictable outcome.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.600-603
• /
• 2000

In the high carbon steel wire drawing process, the wire temperature increases as the drawing speed is faster in order to increase the production rate in the shop floor. The rapid temperature rise causes the wire fracture in the dry wire drawing process. So, in this paper, the isothermal pass schedule program, which includes the calculation method of wire temperature at each pass, is proposed to prevent the wire fracture due to the temperature rise. Using the isothermal pass schedule program, it is newly proposed the pass schedule design system that prevents the cup-cone defects, improves the elongation of the final products and assures further deformation. As a result, the temperature rise of the wire was decreased and the production rate of the final product is remarkably grown up according to the increase of the final drawing speed than that of the conventional process. Also, the proposed pass schedule design system could give a useful information to the process designer who would design the high carbon steel wire drawing process.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2002.09a
• /
• pp.376-378
• /
• 2002

This work was carried out to evaluate the basic performances for 4D CT, which employed continuously rotating conebeam. The performances were evaluated with the same method as the conventional CT, because the standard method of evaluating 4D CT has not yet been established, and we think this result was helpful to establish it. 4D CT can give dynamic volume imaging data continuously and with high-speed. The results were isotropic except for the evaluation of distortion in which small distortions gradually appeared as coming off the center of phantom in longitudinal direction.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.30B no.5
• /
• pp.82-89
• /
• 1993

In this paper, we proposed the autonomous algorithm of pseudo-exhaustive testing for the multi-level combinational logic circuits. For the processing of shared-circuit that existed in each cone-circuit when it backtracked the path from PO to PI of CUT at the conventional verification testing, the dependent relation of PI-P0 is presented by a dependence matrix so it easily partitioned the sub-circuits for the pseudo-exhaustive testing. The test pattern of sub-circuit's C-inputs is generated using a binary counter and the test pattern of I-inputs is synthesized using a singular cover and consistency operation. Thus, according to the test patterns presented with the recipe cube, the number of test pattrens are reduced and it is possible to test concurrently each other subcircuits. The proposed algorithm treated CUT's net-list to the source file and was batch processed from the sub-circuit partitioning to the test pattern generation. It is shown that the range of reduced ration of generated pseudo-exhaustive test pattern exhibits from 85.4% to 95.8% when the average PI-dependency of ISACS bench mark circuits is 69.4%.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.484-489
• /
• 2003

The mass flow rate of gas flow through critical nozzle depends on the nozzle supply conditions and the cross-sectional area at the nozzle throat. In order that the critical nozzle can be operated at a wide range of supply conditions, the nozzle throat diameter should be controlled to change the flow passage area. This can be achieved by means of a variable critical nozzle. In the present study, both experimental and computational works are performed to develop variable critical nozzle. A cone-cylinder with a diameter of d is inserted into conventional critical nozzle. It can move both upstream and downstream, thereby changing the cross-sectional area of the nozzle throat. Computational work using the axisymmetric, compressible Navier-Stokes equations is carried out to simulate the variable critical nozzle flow. An experiment is performed to measure the mass flow rate through variable critical nozzle. The present computational results are in close agreement with measured ones. The boundary layer displacement and momentum thickness are given as a function of Reynolds number. An empirical equation is obtained to predict the discharge coefficient of variable critical nozzle.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.336-336
• /
• 2011

Over the past decades, organic semiconductors have been investigated intensely for their potential in a wide range of optoelectronic device applications since the organic materials have advantages for very light, flexible and low cost device fabrications. In this study, we fabricated small-molecule organic solar cells (OSCs) based on chloro[subphthalocyaninato]boron(III) (SubPc) as an electron donor and $C_{60}$ as an electron acceptor material. Recently SubPc, a cone-shaped molecule with $14{\pi}$-electrons in its aromatic system, has attracted growing attention in small-molecule OSC applications as an electron-donating material for its greater open-circuit voltage (VOC), extinction coefficient and dielectric constant compared to conventional planar metal phthalocyanines. In spite of the power conversion efficiency (PCE) enhancement of small-molecule OSC using SubPc and $C_{60}$, however, the study on the interface between donor-acceptor heterojunction of this system is limited. In this work, SubPc thin films at various thicknesses were deposited by organic molecular beam deposition (OMBD) and the evolution of surface morphology was observed using atomic force microscopy (AFM) and field emission scanning electron microscopy (FE-SEM). We also investigated the influence of film thickness and surface morphology on the PCE of small-molecule OSC devices.