• 한국인터넷방송통신학회논문지
• /
• 제17권6호
• /
• pp.51-57
• /
• 2017

본 논문에서는 Ka 대역 소형 레이다용 주파수합성기를 제안하였다. 제작된 주파수합성기는 시스템에서 요구하는 다양한 파형을 생성하고 고속의 파형 및 주파수 전환을 위해 DDS를 적용하였다. 소형화를 위해 Ku 대역에는 MMIC를 최대한 적용하여 Ka 대역 회로를 소형 집적화 하였고 파형발생부 과 주파수 상향 변환부를 하나의 모듈로하여 설계 제작하였다. 제안된 주파수합성기는 선형 주파수 변조 파형과 위상변조 가능한 주파수 변조 연속 파형 등 발생이 가능하고, 대역폭 1GHz, 주파수 전환 속도 $0.191{\mu}sec$, 1 kHz 오프셋(offset)에서 -89.16 dBc/Hz의 위상잡음, 불요파 -50.9 dBc가 측정되었다.

• 한국전자파학회논문지
• /
• 제21권11호
• /
• pp.1304-1310
• /
• 2010

낮은 고도로 접근하는 고속 표적을 탐지 및 추적하기 위해 사용하는 K 대역의 FMCW(Frequency Modulated Continuous Wave) 레이다의 송수신기 설계 방법을 제안한다. 송신기는 레이다 유효 반사 면적(RCS : Radar Cross Section)이 작은 표적의 추적 및 넓은 송신 안테나 빔 폭으로 인해 고출력이 요구되며, 수신기의 경우는 인터페로메타 방법을 이용하여 표적을 추적하기 위해 다채널 수신기가 요구된다. 송신기는 고출력 송신 증폭기와 도파관 스위치 및 주파수 상향 변환 기판으로 구성된다. 수신기는 5 채널 수신기, 중간 주파수 상향 및 하향 변환 모듈, X 대역 국부 발진기 및 파형 발생 모듈로 세분화 할 수 있다. 제안한 구조를 제작하기 전에 모델링 및 시뮬레이션 방법을 통해 여러 파라메타를 측정함으로써 가능성을 입증한다. 그리고 제안한 송수신기를 산업용 부품을 사용하여 제작하고 성능 파라메타를 측정하였다. 그 결과, 송신기 출력은 39.64 dBm, 수신기 이득은 29.1 dB이며, 그 외 모든 설계 요구 조건을 만족함을 입증하였다.

• 한국정밀공학회지
• /
• 제6권2호
• /
• pp.40-46
• /
• 1989

Recently, the researches on cutting the new material have been done for development of aerospace industrial engineering. Especially, titanium ally is well known as heat resisting, antiwear, anticorrosion and difficult-to-machine materials. Many studies on the analysis of shear angle have been done for improving productivity in cutting these materials. In case of titanium alloy, the saw-toothed type of chip which has wave surface of a triangular form, an eccentric from of a continuous type of chip that is produced in the cutting process, was checked. Nakayama supposed that a maximum shear strewss plane and the shear crack in the free surface made an angle of $45^{\circ}$ .deg. , but it's usually much larger than that. In this paper, the author analyzed the shear conditions of the cutting process in the quick-stopping device with the help SEM-photographs, and measured the hypotenuse angle directly in the photographs of the chips. In conclusion, the author tried to find the shear angle in the cutting process with the saw-toothed chip and compared it with the shear angles which can be calculated from the theories established by others. The results obtained are as follows. 1. In case of the saw-toothed chips, the equivalent cutting ratio can be calculated by using the chip thickness to two-thirds of ramp height. 2. The theory of Ernst-Merchant is not applicable to the titanium and its alloys which does not fractured in accordance with the theory of maximum shear stress. 3. When we cut the titanium alloys which produced the saw-toothed chips, the shear angle can be found with the theories of Rowe-Spick, P.K. Wright and the measurement of hypotenuse angle.

• 한국정밀공학회지
• /
• 제22권8호
• /
• pp.165-173
• /
• 2005

This paper presents the results for deposition of micrometer-scale metal lines on glass for the development of TFT-LCD circuit repair-system. Although there had been a few studies in the late 1980's for the deposition of metallic interconnects by laser-induced chemical vapor deposition, those studies mostly used continuous wave lasers. In this work, a third harmonic Nd:YLF laser (351nm) of high repetition rates, up to 10 KHz, was used as the illumination source and W(CO)s was selected as the precursor. General characteristics of the metal deposit (tungsten) such as height, width, morphology as well as electrical properties were examined for various process conditions. Height of the deposited tungsten lines ranged from 35 to 500 m depending on laser power and scan speed while the width was controlled between 50um using a slit placed in the beam path. The resistivity of the deposited tungsten lines was measured to be below $1{\Omega}{\cdotu}um$, which is an acceptable value according to the manufacturing standard. The tungsten lines produced at high scan speed had good surface morphology with little particles around the patterns. Experimental results demonstrated that it is likely that the deposit forms through a hybrid process, namely through the combination of photolytic and pyrolytic mechanisms.

• 한국정밀공학회지
• /
• 제26권1호
• /
• pp.71-81
• /
• 2009

Die steel for plastic molding were used as mold material of automobile parts and electronic component industry. The material of this paper has superior to mechanical properties, such as repair weldability, corrosion resistance and high temperature strength, required mold parts for semitransparent. Laser-induced surface hardening technology is widely adopted to improver fatigue life and wear resistance via localized hardening at the surface of mold parts. The objective of this research work is to investigate on the characteristics of surface hardening of the laser process parameters, such as beam travel speed, laser power and defocsued spot position, for the case of die steel for plastic molding. Lens for surface hardening of large area is plano-convex type with elliptical profile to maintain uniform laser irradiation. According to the experimental results, large size of hardened layer at the surface of die steel for plastic molding was achieved, and microstructure of this layer was lath martensite. Optimal surface status and mechanical property of hardened layer could be obtained at 1095Watt, $0.25{\sim}0.3m/min$, 0mm (focal length: 232mm) for laser power, beam travel speed, and focal position. Where, heat input was $0.793{\times}10^{3}J/cm^2$, and width of hardened layer was 27.58mm.

• 한국공작기계학회논문집
• /
• 제16권4호
• /
• pp.1-12
• /
• 2007

S45C steel has been widely used in industrial applications, such as crank shafts, gears, main spindles of machine tools, connecting rods, etc., because of its distinguished mechanical property. In the convention arc welding of S45C plates without heat treatments, it is possible for welding defects to take place, such as a void or a hot-crack, due to a high carbon composition of S45C. Laser welding process is widely used in the industrial field due to its numerous advantages: a small heat affected zone(HAZ), deep penetration, high welding speed, single-pass thick section capability, and small distortion after welding. The objective of this research works is to investigate the influence of the process parameters, such as power of laser and welding speed, on the characteristics of laser welding for the case of nickel coated and nickel uncoated S45C steel. As the result of the experiment, in case of butt welding, nickel coated S45C steel has a uniform formation of welding zone and it was judged that the welding nature was better as inner defects and the quantity of spatter were formed relatively fewer than nickel uncoated S45C steel.

• 해양환경안전학회지
• /
• 제9권1호
• /
• pp.41-50
• /
• 2003

한국 연안의 각 항로에 취항하고 있는 대표적인 선형의 여객선들을 대상으로, 각 선형별로 선체운동 계산, 내항성능을 분석하여 선박의 안전성을 평가하였다. 이를 위하여 선박의 안전운항과 가장 밀접한 관련을 갖는 바람과 파랑을 주요 해역별로 비교 분석하였다. 이러한 기강정보를 입력요소로 하여 주요해역을 항행하는 대표적인 선형의 여객선들에 대하여 수치 시뮬레이션을 실시하여 여객선의 항해안정성을 평가하였다.

• Current Optics and Photonics
• /
• 제3권6호
• /
• pp.583-589
• /
• 2019

We report experimental results on 940-nm 350-mW AlGaAs/InGaAs transverse single-mode laser diodes (LDs) adopting graded-index separate confinement heterostructures (GRIN-SCH) and p,n-clad asymmetric structures, with improved temperature and small-divergence beam characteristics under high-output-power operation, for a three-dimensional (3D) motion-recognition sensor. The GRIN-SCH design provides good carrier confinement and prevents current leakage by adding a grading layer between cladding and waveguide layers. The asymmetric design, which differs in refractive-index distribution of p-n cladding layers, reduces the divergence angle at high-power operation and widens the transverse mode distribution to decrease the power density around emission facets. At an optical power of 350 mW under continuous-wave (CW) operation, Gaussian narrow far-field patterns (FFP) are measured with the full width at half maximum vertical divergence angle to be 18 degrees. A threshold current (I_th) of 65 mA, slope efficiency (SE) of 0.98 mW/mA, and operating current (I_op) of 400 mA are obtained at room temperature. Also, we could achieve catastrophic optical damage (COD) of 850 mW and long-term reliability of 60℃ with a TO-56 package.

• 비파괴검사학회지
• /
• 제33권2호
• /
• pp.160-164
• /
• 2013

레이저 초음파검사 장치는 레이저 빔을 이용하여 초음파 신호를 발생시키고 측정하는 비접촉식 결함 검사 장치이다. 이 장치는 펄스 레이저 빔을 이용하여 광대역 주파수 범위를 갖는 초음파 신호를 발생시키고 작은 점으로 집속된 레이저 빔을 이용하여 초음파 신호를 측정하므로 우수한 측정 분해능을 제공한다. 본 연구에서는 이종금속 접촉부식(갈바닉 부식) 현상을 레이저를 이용한 비파괴, 비접촉 방법으로 측정하였다. 부식된 부분에 이물질이 혼합되는 경우를 가정하고, 레이저 초음파 실험을 진행하였다. 시편의 뒷면에서 펄스 레이저로 초음파를 발생시키고, 같은 위치의 앞면에서 CW 레이저와 CFPI를 이용하여 초음파 신호를 획득하였다. 이물질이 존재하는 부분의 초음파 신호 특성을 분석하여 이물질의 위치 및 크기를 측정하였다.

• 대한수의학회지
• /
• 제50권2호
• /
• pp.155-160
• /
• 2010

The objective of this study was to compare wound healing in stomach with $CO_{2}$ laser and scalpel incision by measuring the extent of bleeding, the ease of gastric incision, incision time, degree of adhesion and wound healing degree in dogs. Sixteen healthy dogs were used. Two symmetrical incisions were made in ventral aspect of the stomach between the greater and lesser curvatures were made with scalpel and 0.2 mm spot diameter $CO_{2}$ laser (8W, continuous wave) in sixteen dogs. And then each wound was closed with absorbable suture in a two-layer inverting seromuscular pattern. At 3, 7, 14 and 21 days after initial wounding, each wound was taken for histological observation. On surgery, the extent of bleeding, the ease of incision and incision time showed significant differences between the groups. The $CO_{2}$ laser provided better hemostasis (p < 0.05) and smaller postoperative adhesion compared with the scalpel. However, the scalpel produced faster speed of incision and was easier to handle than the $CO_{2}$ laser (p < 0.05). Although there was no considerable difference between the two groups in histological observation, necrosis and calcium deposit tended to be larger in the $CO_{2}$ laser than in the scalpel.