• Tribology and Lubricants
• /
• v.10 no.4
• /
• pp.75-81
• /
• 1994

In load sharing model, the load is supported by the contacting asperities and the lubricants. The asperity contact area of two sliding surfaces are relatively very small as compared with the apparent contact area. The asperity contact pressure is relatively higher than the lubricant pressure. With the combined effect of asperity and lubricant pressure, the surface roughness and temperature rise must be considered to calculate the lubricant film thickness of the line-contact bearing.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1350-1353
• /
• 2007

An experimental method based on contact resonance is developed to extract the contact parameters of mechanical joints under various clamped conditions. Mechanical joint parameters of shear contact stiffness and damping were extracted for different physical joint parameters such as surface finish of the mating surfaces, the presence of lubrication, the effect of the clamping pressure, and shear load. It was found that the shear contact stiffness values decreased with increasing clamping load and increased with increasing shear loading. Contact damping ratio values were almost constant with clamping load, but decreased with increasing shear load. Moreover, rough surfaces exhibited the highest shear stiffness and contact damping compared to smooth surfaces.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.491-494
• /
• 2002

To assess the electrostatic interaction of surfaces at the triple contact line, the electrostatic field is analyzed by using the finite element method. The Helmholtz free energy is used as a functional which should be minimized under an equilibrium condition. The numerical results are compared with the nonlinear analytical solution for a two-dimensional charged interface and linear solution for a wedge shaped geometry, which shows fairly good agreement. The method is applied to the analysis of electrostatic influence on the contact angle on a charged substrate. The excess free energy found to increase drastically as the contact angle approaches to zero. This excess free energy Plays an opposite role to the Primary electrocapillary effect, as the contact angle gets smaller. This enables an alternative explanation for the contact-angle saturation phenomenon occurring in electrical control of surface tension and contact angle.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2214-2219
• /
• 2008

The thermal contact resistance(TCR) of nanosized contact spots has been investigated through a multiscale analysis which considers the resolution of surface topography. A numerical simulation is performed on the finite element model of rough surfaces. Especially, as the contact size decreases below the phonon mean free path, the size dependent thermal conductivity is considered to calculate the TCR. In our earlier model which follows an elastic material, the TCR increases without limits as the number of nanosized contact spots increases in the process of scale variation. However, the elastoplastic contact induces a finite limit of TCR as the scale varies. The results are explained through the plastic behavior of the two contacting models. Furthermore, the effect of air conduction in nanoscale is also investigated.

• Journal of Distribution Science
• /
• v.18 no.6
• /
• pp.15-24
• /
• 2020

Purpose: The ultimate purpose of this research is to analyze the influence of direct service experience on brand equity components and continuance intention by focusing on cultural marketing at airport, as a huge market place. Design/methodology: This study examines how the cultural contact experience of an airport's cultural marketing activities affect the brand equity components, as well as how these factors affect the continuance intention. A questionnaire survey is conducted for airport users and a total of 313 copies of the questionnaire are analyzed using a structural equation. Results: The results demonstrate that cultural contact service has a positive effect on brand awareness, brand meaning, and perceived value, and all factors of brand equity components have a positive effect on continuance intention. In addition, MTE also has a significant effect on continuance intention. Conclusions/implications: The purpose of this study was to investigate the relationship between the cultural contact and brand attachment of tourists experiencing airport cultural marketing services on the composition factors of airport brand equity. The results of this study can be used not only as basic data to help establish a cultural marketing strategy at an airport, but also as to aid establishing and implementing a long-term marketing strategy for the sustainable growth of an airport.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.9
• /
• pp.943-950
• /
• 2013

This paper describes the thermal contact resistance and its effect on the performance of thermal interface material. An ASTM D 5470 based apparatus is used to measure the thermal interface resistance. Bulk thermal conductivity of different interface material is measured and compared with manufacturers' data. Also, the effect of grease void in the contact surface is investigated using the same apparatus. The flat type thermal interface tester is proposed and compared with conventional one to consider the effect of lateral heat flow. The results show that bulk thermal conductivity alone is not the basis to select the interface material because high bulk thermal conductivity interface material can have high thermal contact resistance, and that the center voiding affects the thermal interface resistance seriously. On the aspect of heat flow direction, thermal impedance of the lateral heat flow shows higher than that of the longitudinal heat flow by sixteen percent.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.330-333
• /
• 2005

The paper presents a numerical solution to the problem of a hot rigid indenter siding over a thermoelastic Winkler foundation with a thermal contact resistance at constant speed. It is shown analytically that no steady-state solution can exist for sufficiently high temperature or sufficiently small normal load or speed regardless of the thermal contact resistance. However, the steady state solution may exist in the same situation if the thermal contact resistance is considered. This means that the effect of the large values of temperature difference and small value of force or velocity which occur at no steady state can be lessened due to the thermal contact resistance. When there is no steady-state the predicted transient behavior involves regions of transient stationary contact interspersed with regions of separation regardless of the thermal contact resistance. Initially, the system typically exhibits a small number of relatively large contact and separation regions, but after the initial transient the trailing edge of the contact area is only established and the leading edge loses contact, reducing the total extent of contact considerably. As time progresses, larger and larger number of small contact areas are established, until eventually the accuracy of the algorithm is limited by the discretization used.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.16 no.4 s.44
• /
• pp.431-441
• /
• 1992

This research was designed to evaluate the effect of need and of demographic variables of adult women on the conformity and individuality in the selection of clothes. 1. There are factors which have effect on variables of need. Marriage status, household type, age have effect on safety need, household type and age have effect on belongingness and love need. Household type and native community have effect on self-esteem need, household type, native community, school career, frequency of contact with mass media have effect on need for self-actualizing. Native community have effect on aesthetic need, and school careers have effect on the desires to know and to understand. 2. Self-esteem need, belongingness and love need, safety need, need for self-actualizing, aesthetic need, frequency of contact with mass media and income as demographic variables are directly related with conformity of clothing. Age, marriage status, native community, household type, school career are indirectly related with conformity of clothing. 3. Self-esteem need, need for self-actualizing, aestheitic need, desires to know and to understand, belongingness and love need, frequency of contact with mass media, household type have direct effect on the individuality of clothing. And age, household type, native community, school career have indirect effect on the individuality of clothing.

• Structural Engineering and Mechanics
• /
• v.53 no.5
• /
• pp.1051-1066
• /
• 2015

The study aims on the effect of material dependency in elastic- plastic contact models by contact analysis of sphere and flat contact model and wheel rail contact model by considering the material properties without friction. The various materials are selected for the analysis based on Young's modulus and yield strength ratio (E/Y). The simulation software 'ANSYS' is employed for this study. The sphere and flat contact model is considered as a flattening model, the stress and strain for different materials are estimated. The simulation of wheel-rail contact model is also performed and the results are compared with the flattening model. The comparative study has also been extended for finding out the mean contact pressure for different materials the E/Y values between 150 and 660. The results show that the elastic-plastic contact analysis for materials up to E/Y=296.6 is depend on the nature of material properties and also for this material the mean contact pressure to yield strength reaches 2.65.

• Tribology and Lubricants
• /
• v.10 no.2
• /
• pp.51-55
• /
• 1994

Rolling friction test was carried out to investigate the effect of the wear amount on rolling contact fatigue process in lubrication oil. The methods of this process were conducted at two Hertzian contact pressure and three slide ratio in each case by employing normalized and annealed carbon steel. During process of the rolling contact fatigue, the number of rotation until surface damage was occurred, the wear amount of rolling contact surface, and residual stress and half-value breadth using X-ray reflection on rolling contact surface were investigated. The result of this study shows that rolling contact fatigue process was directly influenced by wear trend and was confirmed by change of residual stress and half-value breadth on rolling contact surface.