• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.1
• /
• pp.45-50
• /
• 2012

The plate fin and tube type of heat exchanger is widely used in air conditioner, and the heat exchanger is assembled by the mechanical expansion of copper tubes and fastening the aluminum fin. The objective of the present study is to investigate how the mechanical expansion of copper tube affects on the heat transfer performance of a plate fin and tube type heat exchanger. This study has been performed by experimental and numerical methods. The numerical and experimental results show that the tube expansion ratio has a influence on the heat transfer performance. Within the tested expansion ratio, the contact pressure shows the peak value and it decreases as the expansion ratio increases. Air-side heat transfer coefficient increases until the expansion ratio reaches 1.23, and then decreases with the similar pattern to the contact pressure. Also, contact heat transfer coefficient shows the maximum when the contact pressure is highest as well as the air-side heat transfer coefficient.

• Journal of Surface Science and Engineering
• /
• v.46 no.6
• /
• pp.235-241
• /
• 2013

In this study, the effects of alloying elements and thermal aging on the contact resistance of electroplated gold alloy layers were investigated by surface analysis using X-ray photoelectron spectroscopy (XPS). The contact resistance of Au-Ag alloy was lower than that of Au-Ni or Au-Co alloy after thermal aging. The XPS results show that nickel and oxygen present as nickel oxides such as NiO and $Ni_2O_3$ on the surface of gold layers after thermal aging. The increase in the contact resistance after thermal aging is attributable to the nickel oxide layer formed on the surface of the gold layers. The content of nickel diffused from the underlayer during the thermal aging was high in the order of Au-Co, Au-Ni and Au-Ag alloy because the area of grain boundary was large in the order of Au-Ag, Au-Ni and Au-Co alloy.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.8
• /
• pp.945-956
• /
• 1999

This work reports a set of approximate analytical solutions describing the initial transient process of close-contact melting between a rectangular parallelepiped solid and a flat plate on which either constant temperature or constant heat flux is imposed. Not only relative motion of the solid block tangential to the heating plate, but also the density difference between the solid and liquid phase is incorporated in the model. The thin film approximation reduces the force balance between the solid weight and liquid pressure, and the energy balance at the melting front into a simultaneous ordinary differential equation system. The normalized model equations admit compactly expressed analytical solutions which include the already approved two-dimensional solutions as a subset. In particular, the normalized liquid film thickness is independent of all pertinent parameters, thereby facilitating to define the transition period of close-contact melting. A unique behavior of the solid descending velocity due to the density difference is also resolved by the present solution. A new geometric function which alone represents the three-dimensional effect is introduced, and its properties are clarified. One of the representative results is that heat transfer is at least enhanced at the expense of the increase in friction as the cross-sectional shape deviates from the square under the same contact area.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.6
• /
• pp.935-944
• /
• 1987

The surface rolling, one of the plastic working processes, provides good surface roughness with the reduction of diameter and the increase of surface hardness. In this study three Nachi 6000ZZ bearing were used for surface rolling on ductile cast iron. The results obtained are as follows; (1) The good surface roughness can be obtained with roller surface radius of curvature of 24mm after the 2nd rolling. (2) The surface roughness of ductile cast iron was 0.48.mu.mRmax by the contact pressure of 140kgf/mm$^{2}$ and surface hardness was Hv 395 with roller surface radius of curvature of 24mm after the 2nd rolling. (3) The reduction of specimen diameter of ductile cast iron were -12.8.mu.m due to rolling. (4) Within the diameter variation of -11.mu.m, surface roughness and surface hardness were increased, but at the range of exceeding -14.mu.m of the diameter variation the surface roughness became worse and the surface roughness became worse and the surface hardness was increased. (5) Dynamic contact area was about 25% to 30% of static contact area. The calculated contact pressure showed a good agreement with the experimental contact pressure.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.3
• /
• pp.18-23
• /
• 2009

This paper focuses on development of new conveyer directly driven by the contact-less energy transmission system. The effect of the resonant circuit and the flux linkage characteristics caused from that are analyzed by using 3D finite element analysis. From the result it is shown that the resonant circuit needs to transfer energy from the primary core to the secondary core. Also the influence of the linear induction motor on the contact-less energy transmission system is presented. New conveyer and the experimental apparatus was manufactured by using the contact-less energy transmission system and the linear induction motor. Possibility of realization of the conveyer is proved by comparison the simulation result which is obtained by using 2D finite element analysis with experimental one and the characteristic of the voltage and resonant current.

• Proceedings of the KIEE Conference
• /
• 2009.04a
• /
• pp.10-12
• /
• 2009

Electromagnetic Interference(EMI) in electric railway operation has become increasingly important. The components within very high power electronic, and the circuits for treating low-level signals, comprise complex system that must coexist and be highly reliable. To study it, It were included how much the HEMU-400X generates EMI and it has an effect on the power conversion units which resulted from Power Line Disturbance (PLD) phenomenon by contact loss during its running. In this study, the dynamic characteristic of a contact wire and pantograph suppling electrical power to high-speed trains are investigated. The analysis of the loss of contact based on Power Simulator program software is performed to develop power line disturbance model suitable for high speed operation. It is confirmed that a contact wire and pantograph model are necessary for studying the dynamic behavior of the pantograph system.

• The Journal of Korean Medicine Ophthalmology and Otolaryngology and Dermatology
• /
• v.29 no.4
• /
• pp.169-181
• /
• 2016

Objectives : The purpose of this case report is to know the effect of Korean medical treatments on occupational contact dermatitis. Methods : We reported 2 cases who visited Allergy and Derma-Cosmetic Clinic of Kyung Hee University Hospital at Gangdong. They were diagnosed with occupational contact dermatitis and treated by Korean medical treatment. Results : One patient recovered after 13 days of admission and total 9 months of outpatient period. Another patient recovered after 9 days of admission and total 7 months of outpatients period through Korean Medical Treatment. Conclusions : We may expect that Korean medical treatment had therapeutic effects on occupational contact dermatitis, but the additional study will be conducted for revealing the exact therapeutic effects.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.607-612
• /
• 2004

Disc brake noise continues to be a major concern throughout the automotive industry despite efforts to reduce its occurrence. Eliminating vibrations during braking is an important task for both vehicle passenger comfort and reducing the overall environmental noise levels. There are several classes of disc brake noise, the major ones being squeal, judder, groan, and moan. In this study, analytical model for moan noise of rear disk brake is investigated. Modeling of the disc brake assembly to take account of the effect of different geometrical and contact parameters is studied through the use of multi-body model. The contact stiffness of the caliper and torque member plays an important role in controlling brake vibration. Therefore, a suitable material pair at the caliper/body contact has been made. An ADAMS model of a rear disc brake system was integrated with a flexible suspension trailng arm from MSC/NASTRAN. A fully non-linear dynamic simulatin of brake system behavior, containing rigid and flexible bodies, was performed for a Prescribed set of operating conditions. Simulation results were validated using data from vehicle experimental testing.

• Korean Journal of Occupational Health Nursing
• /
• v.25 no.2
• /
• pp.108-117
• /
• 2016

Purpose: The purpose of this study was to determine the relationship between customer contact service and mental health among Korean taxi drivers. Methods: This was a secondary analysis of data collected from the 2015 Korean Working Conditions Survey. The sample included 496 taxi drivers in South Korea. The effect of customer contact service on mental health was analyzed using logistic regression analysis. The independent variables were general characteristics, working conditions, and hazardous factors in interactive service. Results: The prevalence of poor mental health was 56.3%. Taxi drivers experienced emotional involvement (17.2%), hiding feeling (32.0%), and contact with angry clients (18.3%) in their job. During the first month of their work, 33.7% experienced verbal abuse and 12.3% threats/humiliating behaviors. In bivariate analysis, verbal abuse, threats/humiliating behaviors, and physical violence were associated with mental health of taxi drivers. Multiple logistic regression analysis revealed 'emotional involvement' and 'contact with angry clients' were significant predictors of mental health. Conclusion: The findings of this study may be useful in developing intervention programs to improve the mental health of taxi drivers in South Korea.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1326-1330
• /
• 2008

The failure mode of steel road wheels in a vehicle is cracks from ventilation hole through to contact plane on steel wheel's disc plate. But a number of cracks of Cornering Fatigue Limit Test is on contact plane near to wheel nut mounting area, even though it's satisfied with specified cycles. So this paper searches out causes to improve durability and reliability of C.F.T by uni-axial bending moment test. The verified cause is a "fretting" on contact area of steel wheel. In result, this paper suggests a solution to prevent a fretting by inserting a damping shim, 0.7mm between steel wheel contact areas. Therefore this paper makes it possible to move crack position of C.F.T in steel wheel from contact plane to vehicle's failure mode.