• Tribology and Lubricants
• /
• 제30권2호
• /
• pp.99-107
• /
• 2014

Fretting corrosion tests are conducted with a constant displacement amplitude using silver-plated brass coupons to investigate the effect of contact pressure on fretting corrosion. Three behaviors are identified based on the change in electric resistance and friction coefficient during the fretting test period, and the identified behaviors are dependent on the magnitude of the applied load. The failure cycle ($N_f$) with an electric resistance of 0.1 D cannot be achieved due to the adhesion behavior of the metal and metal contact under the higher applied load of 0.45 N. This suggests that an average contact pressure higher than 159 MPa for the silver-coated connector is desirable to gain an almost infinite lifetime. The relationship between the electric contact resistance (R) and the average contact pressure (p) can be written as $p=106.2{\times}{\Omega}^{-1.5}$.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.19-26
• /
• 2001

The wear characteristic of Zircaloy-4 tube, which is used for a cladding of light water reactor fuel rod, is investigated experimentally. The experiment is conducted with contacting the crossed tube specimens in air as well as in water at room temperature with various combination of contact normal force and sliding distance of reciprocating motion. The contour and the volume of each wear are examined to study the effect of contact condition and environment on wear. As a result, it is found that the wear volume in the water environment is larger than that in the air for all the contact (i.e., force and sliding distance) conditions. However, the wear depth is greater in air than in water if the contact normal force and the sliding distance are larger. These are explained by the ease of detachment of wear particles from the contact surface. On the other hand, workrate model is applied with the contact shear force range measured by our wear tester. Investigated is the correlation between the workrate and the wear volume increase rate of the present experiment. The parabolic curve is found to fit well for the present wear data.

• Journal of the Korean Home Economics Association
• /
• 제50권5호
• /
• pp.115-124
• /
• 2012

The purpose of this study was to investigate the mediating effects of parental neglect on the relationship between family environment, such as economic status and harmony of family and contact with harmful environments. The data came from the 2009 Korean Survey on the Rights of Youth (N = 6,601). The data was analyzed using Structural Equation Modeling by means of SPSS 17.0 and AMOS 7.0. Bootstrap method used to test significant mediating effects. We found that family environment influences an adolescent's contact with harmful environments through parental neglect, showing that family environment has both indirect and direct effects. The results suggested that a family with low socio-economic status and more stress than harmony engenders a negative effect on the behavior of parents providing care and affection. This neglect influences the adolescent's contact with harmful environments such as harmful media and facilities. It must be acknowledged that parental care and suitable affection play a minimal role in adolescent's contact with harmful environments.

• Journal of the Korean Home Economics Association
• /
• 제44권8호
• /
• pp.23-32
• /
• 2006

Understanding the experience of parents without custody after divorce is important in terms of facilitating their adjustment and positive relationships with their children. Ninety-two noncustodial parents divorced within the previous 5 years completed a structured questionnaire. We examined differences between noncustodial fathers and mothers in terms of the frequency of the contact and the relationship satisfaction with children. In addition, using the regression model, we analyzed the effects of several characteristics of noncustodial parents, including gender, on the frequency of contact as well as the relationship satisfaction with children. The main results of the study are as follows. First, noncustodial fathers and mothers exhibited similar low levels of contact by phone and in-person visits. Second, noncustodial parents with a child older than 8 years old visited the child more frequently, and were more satisfied than noncustodial parents with younger children. Third, the level of desire to gain the child custody had a significant effect on the frequency of contact and the satisfaction of the relationship between the noncustodial parents and their children. Fourth, noncustodial parents with more positive feeling about their former spouse contacted more frequently with the children. Fifth, compared with noncustodial fathers, noncustodial mothers demonstrated a higher relationship satisfaction with their children.

• Journal of the Korean Society of Food Science and Nutrition
• /
• 제29권1호
• /
• pp.111-115
• /
• 2000

This study was to investigate antiallergic contact hypersensitivity of the polyphenol fractons isolated from persimmon leaves (Diospyros kaki folum). The result of the allergic contact dermatitis is a common skin disease resulting from specific immunologic sensitization due to topically applied allergens. Here the contact hypersensitivity was assayed and obdominal skin morphological changes including mast cells were examined. At contact hypersensitivity assay, less right ear swelling occured in the polyphenol fraction I, II and III groups compared to the control group. The number of mast cells was significantly decreased in the sample groups than the control group.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 추계학술발표대회 논문집
• /
• pp.350-355
• /
• 2009

The crysralline silicon solar cell where the solar cell market grows rapidly is occupying of about 85% or more high efficiency and low cost endeavors many crystalline solar cells. The fabricaion process of high efficiency crystalline silicon solar cells necessitate complicated fabrication processes and Ti/Pd/AG contact, This metal contacts have only been used in limited areas in spite of their good srability and low contact resistance because of expensive materials and process. Commercial solar cells with screen-printed solar cells formed by using Ag paste suffer from loe fill factor and high contact resistance and low aspect ratio. Ni and Cu metal contacts have been formed by using electroless plating and light-induced electro plating techniques to replace the Ti/Pd/Ag and screen-printed Ag contacts. Copper and Silver can be plated by electro & light-induced plating method. Light-induced plating makes use the photovoltaic effect of solar cell to deposit the metal on the front contact. The cell is immersed into the electrolytic plating bath and irradiated at the front side by light source, which leads to a current density in the front side grid. Electroless plated Ni/ Electro&light-induced plated Cu/ Light-induced plated Ag contact solar cells result in an energy conversion efficiency of 16.446 % on 0.2~0.6${\Omega}$ cm, $20{\times}20mm^2$, CZ(Czochralski) wafer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.521-524
• /
• 2001

In this letter, we report on the investigation of Ti, Pt/Si/Ti Ohmic contacts to p-type 4H-SiC. The contacts were formed by a 2-step vacuum annealing at 500$^{\circ}C$ for 1h, 950$^{\circ}C$ for 10 min respectively. The contact resistances were measured using the transmission line model method, which resulted in specific contact resistivities in the 3.5x10$\^$-3/ and 6.2x10$\^$-4/ ohm/$\textrm{cm}^2$, and the physical properties of the contacts were examined using x-ray diffraction, microscopy, AES(auger electron spectroscopy). AES analysis has shown that, at this anneal temperature, there was a intermixing of the Ti and Si, migration of into SiC. Overlayer of Pt had the effect of decreasing the specific contact resistivity and improving the surface morphology of the annealed contact.

• Transactions on Electrical and Electronic Materials
• /
• 제17권1호
• /
• pp.46-49
• /
• 2016

A thin film transistor (TFT) has been fabricated using the amorphous 0.5 wt% Si doped zinc-tin-oxide (a-0.5 SZTO) with different electrodes made of either aluminium (Al) or titanium/aluminium(Ti/Al). Contact resistance and total channel resistance of a-0.5SZTO TFTs have been investigated and compared using the transmission line method (TLM). We measured the total resistance of 1.0×10² Ω/cm using Ti/Al electrodes. This result is due to Ti, which is a material known for its adhesion layer. We found that the Ti/Al electrode showed better contact characteristics between the channel and electrodes compared with that made of Al only. The former showed a less contact and total resistance. We achieved high performance of the TFTs characteristic, such as Vth of 2.6 V, field effect mobility of 20.1 cm² V⁻¹s⁻¹, S.S of 0.9 Vdecade⁻¹, and on/off current ratio of 9.7×10⁶ A. It was demonstrated that the Ti/Al electrodes improved performance of TFTs due to enhanced contact resistance.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• 제18권11호
• /
• pp.35-40
• /
• 2019

Laser processing has been used in various fields. In this study, the feasibility of a hydrophobic surface was investigated through the laser cladding technique. A diode laser was used, and the output was set to 600-800 W. Seven different specimens were prepared with different cladding widths and spacings, and the contact angles for water droplets were evaluated. As a result, the contact angle of water droplets measured in the direction parallel to the cladding line was higher than that in the vertical direction. The wider the cladding width and the cladding space, the higher the contact angle in the parallel direction. It is thought that when a higher contact angle is formed in the parallel direction, more air can be placed in the valley between the cladding lines. In addition, for the hydrophobic coating effect, the contact angle of the coated cladding surface was increased by about $5-15^{\circ}$ as a whole compared to the coated smooth surface. It was confirmed that the wetting characteristics were improved through the cladding.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권1호
• /
• pp.59-69
• /
• 2019

This paper focuses on the numerical simulation of ice abrasion induced by unbreakable ice floe. Under the assumption that unbreakable floes behave as rigid body, the Discrete Element Method (DEM) was applied to simulate the interaction between a fixed structure and ice floes. DEM is a numerical technique which is eligible for computing the motion and effect of a large number of particles. In DEM simulation, individual ice floe was treated as single rigid element which interacts with each other following the given interaction rules. Interactions between the ice floes and structure were defined by soft contact and viscous Coulomb friction laws. To derive the details of the interactions in terms of interaction parameters, the Finite Element Method (FEM) was employed. An abrasion process between a structure and an ice floe was simulated by FEM, and the parameters in DEM such as contact stiffness, contact damping coefficient, etc. were calibrated based on the FEM result. Resultantly, contact length and contact path length, which are the most important factors in ice abrasion prediction, were calculated from both DEM and FEM and compared with each other. The results showed good correspondence between the two results, providing superior numerical efficiency of DEM.