• Journal of Korean Tunnelling and Underground Space Association
• /
• v.15 no.1
• /
• pp.25-31
• /
• 2013

In this study, the total loss and damage ratio of maintenance monitoring which is installed and operated in the domestic and foreign tunnel structure is researched and analyzed for estimating the loss and damage ratio of maintenance monitoring sensor of subway tunnel. The total loss and damage ratio at the elapsed time of 5-6 years after installation is 14.2% in the Seoul metro line no.5,6 and 7, 14.8% in the section 1 of the Seoul metro line no.9, 13.9% in the Channel tunnel of England and all of them are close to 15%. Therefore, it is reasonable to reflect that the total loss and damage ratio of maintenance monitoring sensor of subway tunnel is estimated provisionally 15% on design, and hence the study of the loss and damage ratio with the number of elapsed years in long-term by the measurement category will be needed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.5B
• /
• pp.824-832
• /
• 2010

In construction structure management, the effects of investigation by the professional manager is dependent on the cost, the inspection periods and methods. Therefore, effective and automated maintenance system for the target structure is required. Although some bridge monitoring systems are operating using wire based networks, the performance is not good enough to show sufficient ability as integrated bridge management system. In this paper, we design and implement an integrated bridge management system based on sensor networks. Two expert modules for bridge management and the integrated system management are provided. Moreover, web-based monitoring system is also designed for users at anywhere. The results show that the system is effective and readily available.

• Smart Structures and Systems
• /
• v.1 no.4
• /
• pp.355-368
• /
• 2005

Large and complex structures are being built now-a-days and, they are required to be functional even under extreme loading and environmental conditions. In order to meet the safety and maintenance demands, there is a need to build sensors integrated structural system, which can sense and provide necessary information about the structural response to complex loading and environment. Sophisticated tools have been developed for the design and construction of civil engineering structures. However, very little has been accomplished in the area of monitoring and rehabilitation. The employment of appropriate sensor is therefore crucial, and efforts must be directed towards non-destructive testing techniques that remain functional throughout the life of the structure. Fiber optic sensors are emerging as a superior non-destructive tool for evaluating the health of civil engineering structures. Flexibility, small in size and corrosion resistance of optical fibers allow them to be directly embedded in concrete structures. The inherent advantages of fiber optic sensors over conventional sensors include high resolution, ability to work in difficult environment, immunity from electromagnetic interference, large band width of signal, low noise and high sensitivity. This paper brings out the potential and current status of technology of fiber optic sensors for civil engineering applications. The importance of employing fiber optic sensors for health monitoring of civil engineering structures has been highlighted. Details of laboratory studies carried out on fiber optic strain sensors to assess their suitability for civil engineering applications are also covered.

• Journal of Satellite, Information and Communications
• /
• v.7 no.1
• /
• pp.27-32
• /
• 2012

In this paper, the wastewater treatment plant sludge proposed TN/TP sensor data collected an efficient monitoring system in order to implement status monitoring to build WiFi networks. Also we sludge concentration and TN/TP sensor data were collected from wastewater treatment plant. It is able to be monitored sensor data through smart devices(Smart phones, smart pad, tablet PC, etc.) and pc. In addition, when certain events occur immediately be able to cope by adding features to enable efficient and rapid processing, real-time status can be checked by ensuring improved user access and convenience. We has built a WiFi network for to transfer data efficiently. It proved its effectiveness by analysis of sensor communication network. Therefore, we have verified the usefulness of the proposed technology.

• Journal of Advanced Navigation Technology
• /
• v.22 no.5
• /
• pp.485-489
• /
• 2018

For the construction of smart factory that are part of the Fourth Industrial Revolution, data from the production environments and production machines should be collected, analyzed, and feedback should be given to predict when failures take place or parts should be replaced. For this purpose, a system that monitors the production environments and the status of the production machines are required. In this paper, the monitoring system for mobile devices and PC is implemented by collecting environmental data from production sites and sensor data of production machine using LoRa, a low-power wireless communication technology. On the mobile devices, production environments and vibration data can be displayed in real time. In PC monitoring program, sensor data can be displayed graphically to check standard deviation and data variation. The implemented system is used to collect data such as temperature, humidity, and atmospheric pressure of the production environment, and vibration data of production machines.

• International Journal of Concrete Structures and Materials
• /
• v.9 no.3
• /
• pp.307-321
• /
• 2015

The primary objective of this study is to investigate the feasibility of an innovative surface-mount sensor, made of a piezoelectric disc (PZT sensor), as a consistent source for surface wave velocity and transmission measurements in concrete structures. To this end, one concrete slab with lateral dimensions of 1500 by 1500 mm and a thickness of 200 mm was prepared in the laboratory. The concrete slab had a notch-type, surface-breaking crack at its center, with depths increasing from 0 to 100 mm at stepwise intervals of 10 mm. A PZT sensor was attached to the concrete surface and used to generate incident surface waves for surface wave measurements. Two accelerometers were used to measure the surface waves. Signals generated by the PZT sensors show a broad bandwidth with a center frequency around 40 kHz, and very good signal consistency in the frequency range from 0 to 100 kHz. Furthermore, repeatability of the surface wave velocity and transmission measurements is significantly improved compared to that obtained using manual impact sources. In addition, the PZT sensors are demonstrated to be effective for monitoring an actual surface-breaking crack in a concrete beam specimen subjected to various external loadings (compressive and flexural loading with stepwise increases). The findings in this study demonstrate that the surface mount sensor has great potential as a consistent source for surface wave velocity and transmission measurements for automated health monitoring of concrete structures.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.05a
• /
• pp.283-284
• /
• 2021

The domestic and overseas IoT (Internet of Things)-based automation industry is developing remarkably, and the development of this automation technology is further accelerated by the development of sensor technology. In recent years, the smart farm industry for the purpose of growing crops based on various sensor technologies is rapidly developing. In the case of smart farms, real-time monitoring and mobile services are provided by measuring representative environmental data such as temperature, humidity, and CO2 required for crop cultivation. Most of these environmental monitoring and control operations use the RS-485-based Modbus (RTU) communication method. In this paper, we intend to test the performance of sensor data and actuator information required for smart farm construction by building a platform for controlling sensor data and actuators based on LabView using MQTT (Message Queuing Telemetry Transport), an IoT standard protocol.

• Smart Structures and Systems
• /
• v.15 no.3
• /
• pp.769-785
• /
• 2015

Although timber structures have been extensively used in underground temporary supporting system, their actual performance is poorly understood, resulting in potentially conservative and over-engineered design. In this paper, a novel wireless sensor technology, SmartPlank, is introduced to monitor the field performance of timber structures during underground construction. It consists of a wooden beam equipped with a streamlined wireless sensor node, two thin foil strain gauges and two temperature sensors, which enables to measure the strain and temperature at two sides of the beam, and to transmit this information in real-time over an IPv6 (6LowPan) multi-hop wireless mesh network and Internet. Four SmartPlanks were deployed at the London Underground's Tottenham Court Road (TCR) station redevelopment site during the Stair 14 excavation, together with seven relay nodes and a gateway. The monitoring started from August 2013, and will last for one and a half years until the Central Line possession in 2015. This paper reports both the short-term and long-term performances of the monitored timber structures. The grouting effect on the short-term performance of timber structures is highlighted; the grout injection process creates a large downward pressure on the top surface of the SmartPlank. The short and long term earth pressures applied to the monitored structures are estimated from the measured strains, and the estimated values are compared to the design loads.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.05a
• /
• pp.542-545
• /
• 2022

Recently, the Act on the Punishment of Severe Disasters has drawn attention to the construction environment. A common way to check the safety management of the construction site is for workers to check the site with their own eyes. However, this method is inevitably affected by the limitations of workers' abilities, resulting in fatigue and reduced work efficiency. For this reason, it cannot be an efficient method. Thus, we intend to help the working environment and construction site safety through this study, by proposing an efficient ICT safety management system that can supplement the above methods. In this paper explain the design of the access management system using RFID and the field information monitoring method through noise sensors and fine dust sensors. In addition, we propose a system that can prevent accidents between heavy equipment and people with a PIR sensor, and prevent safety accidents by grasping the slope of the building being worked through a gyro sensor.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2004.10a
• /
• pp.451-458
• /
• 2004

The caisson-type breakwaters have been widely used in the area of harbor construction. Because of the importance of the breakwaters, structural health monitoring in the breakwaters by using appropriate methods is of great needs. In this study, a caisson-type breakwater that has fatigue cracks due to wave-impact is investigated. First, a signal-based structural health monitoring method is proposed for the breakwaters structures. Excitation and sensor systems are designed on finite element model and monitoring categories are also selected. Structural health monitoring was realized by using measured dynamic response signals and analyzed information.