• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2110-2112
• /
• 1997

The induction motor drive for the spindle of machining center is required to do not only a constant torque operation in low speed region(below base rpm), but also a constant power operation in high speed region(beyond base rpm). Also, control voltage shortage due to high speed operation must be overcome. The vector controlled inverter system with input 3 phase pwm converter is designed for that kind of condition. We experimented the performance of the inverter system with spindle motor made by Hyosung industries co.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.305-310
• /
• 2001

Within some degree of journal misalignment, maximum pressure, maximum temperature, bearing load, friction and side leakage in high-speed journal bearing operation are examined under the condition of variable density and specific heat. The results are compared with the calculation results under the conditions of constant density and specific heat, and variable density and constant specific heat. It is found that the effects of variable density and specific heat on shaft misalignment are significant in determining the load capacity of a journal bearing operating at high speed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.3
• /
• pp.514-518
• /
• 2007

It is necessary to modify the state-of-the-art of speed control theory because of the phase asymmetry in the Linear Induction Motor (LIM)and for the constant speed control of mover using single vector control inverter system, it is important that primary stack is located in appropriated intervals in the 3D conveyer system using LIM. The dynamic characteristic analysis method of the vector controlled LIM using coupled FEM and control algorithm taking into account the movement is proposed. The focus of this paper is the analysis relative to selecting primary stack intervals in order to constant speed control in the 3D conveyer system using LIM.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.417-420
• /
• 2000

In order to the torque control the indirect flux control was performed by controlling the ratio of e/f and the q-axis flux was estimated by the slip command and q-axis flux was estimated by the slip command and q-axis current in the rotor circuits. Also the frequency was controlled to keep on the q-axis flux to be zero and the constant torque characteristics could be obtained by generation the preset torque. In the induction motor driven by the boltage source inverter with the constant voltage and frequency the speed variation is expressed as a slip So the speed control can be achieved by slip compensation The slip was calculated with a q-flux current filtered by first-order filter and as the result the error problem which may occur in current detection was eliminated

• Journal of Industrial Technology
• /
• v.24 no.B
• /
• pp.171-176
• /
• 2004

The effects of agitation and aeration for exopolysaccharide(EPS) production through batch cultivation of an Enterobacter sp. isolated from the composter were investigated. During the EPS fermentation under conditions of constant agitation speed from 200 to 900 rpm and constant aeration rate of 0.5-2.5 vvm, the low yields of EPS(4.8-5.2g/L) was observed as the viscosity increase of culture broth. With the stepwise increases in agitation speed and aeration rate, the EPS production and the viscosity of EPS were increased 1.3~1.4 times and 2.3~3.6 times higher than those of the fixed conditions, respectively. Therefore, these stepwise increases were considered as the key operating parameters for enhancing EPS production. The max. EPS(6.8g/L) and viscosity(14,000cp) were obtained when the agitation speed was increased from 300 to 900 rpm for 54hrs at 1.5 vvm.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.579-582
• /
• 1989

The air-cooled waterwheel generator has a fan connected to waterwheel shaft or motor driven fan or fans. The fans are operated at constant speed, constant input, regardless of generator loss which is varied according to generator output and coolant the perature. Energy savings may he possible if the cooling air flow is controlled according to generato output and air temperature depending on season. The simulation and experience have been done on the 22.6 KVA Waterwheel generator by using AC variable speed drive. The results gave us los cut of generator.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.5 s.176
• /
• pp.1231-1237
• /
• 2000

Dynamics of a rotating cantilever beam near its critical angular speed is investigated in this paper. The external, force is idealized as a periodic function which has the same period as the rotati ng frequency of the beam. The equations of motion are derived and transformed into a dimensionless form. A prescribed spin-up motion is employed for the rotating motion. Numerical study shows that the steady state and the transient responses of the beam are affected by the spin-up time constant and there exists a time constant at which the maximum transient response becomes minimum.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.83-84
• /
• 2015

In order to use the high-speed range of Interior Permanent Magnet Synchronous Motor(same as IPMSM above), the motor should be at flux weakening control status. High-speed range is called field weakening control region or constant power region, and explain the basic theory of flux weakening control used in the constant power region. Back electromotive force of IPMSM is measured. and field weakening conrtrol driving characteristics is configurated verification test. Through experimentation speed-torque characteristic curve, the efficiency variation corresponding to the current phase angl,the efficiency map were produced.

• Structural Engineering and Mechanics
• /
• v.61 no.4
• /
• pp.453-461
• /
• 2017

This paper presents the series multiple tuned mass dampers (STMDs) to suppress the resonant vibrations of railway bridges under the passage of high-speed trains (HSTs). A STMD device consisting of two spring-mass-damper units connected each other in series is installed on the bridge. In solution, bridge is modeled as a simply-supported Euler-Bernoulli beam with constant cross-section, and vehicle is simulated as a series of moving forces with constant speed. By the assumed mode method, the governing equations of motion of the beam-TMD device coupled system traversed by a moving train are obtained. The optimum values for the parameters of the STMD device are obtained for the criterion based on the minimization of the maximum dynamic displacement of the beam at its midspan. Single TMD and multiple TMDs in parallel are also considered for demonstration of the STMD device's performance. The results show that STMDs are effective in bridge vibration suppression and robust to parameters' change in the main system and the absorber itself.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.234-238
• /
• 1998

Parameter estimation of induction motor for vector control presented in this paper can be easily implemented and applied to inverters in the industrial field, because it needs no additional hardware such as voltage sensor and measuring equipment. At first, the stator resistance including switching loss of inverter is measured by simple voltage-current equation. Next, in pre-magnetization of machine by imposing the d-axis constant field-current, q-axis torque current is forced to the machine until its speed feedback reachs to pre-defined level of speed limit. At this time, we can measure the rotor time-constant by decreasing the distorted output-voltage of inverter. At last, stator inductance, transient inductance, and moment of inertia can be measured by the relationship of output voltage, output torque and speed feedback. The validity and usufulness of this method is verified by experimental results.