• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.6
• /
• pp.671-677
• /
• 2015

A novel phase interpolator (PI) based linear model of multipath ring oscillator (MPRO) is described in this paper. By modeling each delay cell as an ideal summer followed by a single pole RC filter, the oscillation frequency is derived for a 4-stage differential MPRO. It is analytically proved that the oscillation frequency increases with the growth of the forwarding factor ${\alpha}$, which is also confirmed quantitatively through simulation. Based on the proposed model, it is shown that the power to frequency ratio keeps constant as the speed increases. Running at the same speed, a 4-stage MPRO can outperform the corresponding single-stage ring oscillator (SPRO) with 27% power saving, making MPRO with a large forwarding factor ${\alpha}$ an attractive option for lower power applications.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.197-198
• /
• 2008

Even if the DFT calculation is one of the general method to do phasor estimation, it can't adapt to alteration of the frequency. The Frequency is fastened to 60Hz in the ideal power system. However the frequency is not constant in real power system and fluctuates more followed by conditions of the power system. In these cases, the accurate phasor estimation is impossible by using a common DFT calculation, so that a frequency - adaptive phasor estimation method based on the fourier transform is proposed in this paper.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.956-957
• /
• 2015

This paper analyzes a operating characteristic for maximum power point tracking (MPPT) of photovoltaic generation system. MPPT methods are used to maximize PV array output power by tracking maximum power point(MPP) continuously. To increase the output efficiency of PV system, it is important to have more efficient MPPT. MPPT algorithm is widely used the control method such as the perturbation and observation(PO) method, incremental conductance(IC) method and constant voltage(CV) method. In case of the radiation is changed, this paper proposes a response characteristic with MPPT control algorithms. Also, it proposes the direct for a novel MPPT control algorithm development through the analyzed data, hereby proves the effectiveness of this paper.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.304-309
• /
• 2005

This paper presents an electronic ballast using a step down converter, a low frequency inverter for high intensity short-arc discharge lamp. The proposed ballast is composed of a full-wave rectifier, a step down converter operated as a current source with power regulation and a low frequency inverter with external ignition circuit. The ignition circuit generates high voltage pulse of $3{\sim}5[kV]$ peak, 130[Hz] periodically. Moreover, it is able to reignite at regular intervals by protective circuit. As experimental results on the test, acoustic resonance phenomenon is eliminated by operating the low frequency square wave voltage and current. Lamp voltage, current and consumption power are measured 123.8[V], 8.1[A] and 1,002[W], respectively. It was confirmed that the designed ballast operate the lamp with a constant power.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.19-21
• /
• 2006

In contrast with DC source, Fell cell has non linear characteristics that has lange voltage fluctuation due to load variation, and slow dynamic characteristics. when the loads are increase, the ripples of input and output voltage, also power densities, of inductor, capacitor, and switching devices, are bulky. This paper presents Interleaved boost converter using Fuel cell stacks, proposed converter has merits to promote power densities without increasing loss. Because each converter has same switching frequency and constant phase difference. In this paper, Interleaved boost converter was design for 1[kW], it's validity was proved by simulation and experiments.

• Journal of Power Electronics
• /
• v.2 no.3
• /
• pp.162-170
• /
• 2002

Voltage sag detection algorithm for voltage sag corrector is proposed in this paper. To quantify the standard of voltage unbalance under the faulted conditions, the 3-phase unbalanced voltages are decomposed into two balanced 3-phase symmetrical components of the positive and negative sequence voltages, which is defined by the magnitude factor (MF) and unbalance factor (UF). It is analyzed that MWF and UF values are given as the dc constant values even though under the voltage unbalance condition. This paper also proposes the control scheme of the instantaneous voltage sag corrector based on this detection algorithm. The validity of the proposed algorithm is verified through the EMTDC simulation and experiments.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.515-518
• /
• 2002

A synchronous generator is equipped with an automatic voltage regulator(AVR), which is responsible for keeping the output voltage constant under normal operating conditions at various levels. The output voltage of Synchronous Generator is regulated constantly by field voltage control in excitation system. High frequency PWM converter (Buck converter) type excitation system for synchronous generator that can sustain prefer output voltage level even at the fault condition happened. The proper operation of the proposed excitation system was verified through the simulations and the experiments.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.653-656
• /
• 2002

This paper presents the development of 15G(Integrate Starter Generator). The ISG is the crank shaft mount type and it is installed at tile flywheel. The wide operating range of ISG requires large constant power speed ratio, good overload performance and high efficiency. High saliency ratio permanent magnet motor is developed for the ISG applications and 500A MOSFET inverter is designed to derive the ISG. The characteristic of developed ISG is investigated using the special test-bed for the 42V PowerNet and the detailed results is presented

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.938-943
• /
• 1998

The induction motor of the electric vehicles is controlled based on the vector control method to obtain good torque control characteristics. In the conventional vector control system, the field exciting current should be kept on a constant value to keep a stable flux level. This method has a liability that core loss becomes increasing at the light load region. To solve this liability, the efficiency maximizing control method of the vector controlled induction motor is proposed in thid paper. We developed light weight water cooled 60kW induction motor drive system which adopts our method and fabricated a conversion electric car for actual vehicle test. We demonstrate the usefulness of drive system by comparing its driving mode with conventional field oriented system and an efficiency maximizing controlled induction motor.

• Journal of Power Electronics
• /
• v.17 no.5
• /
• pp.1127-1136
• /
• 2017

This paper proposes a new soft switching dual input converter for renewable energy systems. Multi-input converters are produced by combining discrete converters. These converters reduce the number of circuit elements, cost, volume and weight of the converter and provide a constant output power in different weather conditions. Furthermore, soft switching techniques can be applied to increase efficiency. In this paper, a Zero Voltage Transition (ZVT) dual input boost converter is presented. Only one auxiliary circuit is used to provide the soft switching condition for all of the semiconductor elements. The proposed converter, which is simulated by ORCAD software, is theoretically analyzed. To confirm the validity of the theoretical analysis, a prototype of proposed converter was constructed. Simulation and experimental results confirm the theoretical analysis. An efficiency comparison shows a one percent improvement at nominal loads.