• Journal of Korean Society of Water and Wastewater
• /
• v.33 no.4
• /
• pp.243-250
• /
• 2019

This objective of this study was to investigate the degradation characteristics of phenol, a refractory substance, by using a submerged dielectric barrier discharge (DBD) plasma reactor. To indirectly determine the concentration of active species produced in the DBD plasma, the dissolved ozone was measured. To investigate the phenol degradation characteristics, the phenol and chemical oxygen demand (COD) concentrations were evaluated based on pH and the discharge power. The dissolved ozone was measured based on the air flow rate and power discharged. The highest dissolved ozone concentration was recorded when the injected air flow rate was 5 L/min. At a discharge power of 40W as compared to 70W, the dissolved ozone was approximately 2.7 - 6.5 times higher. In regards to phenol degradation, the final degradation rate was highest at about 74.06%, when the initial pH was 10. At a discharged power of 40W, the rate of phenol decomposition was observed to be approximately 1.25 times higher compared to when the discharged power was 70W. It was established that the phenol degradation reaction was a primary reaction, and when the discharge power was 40W as opposed to 70W, the reaction rate constant(k) was approximately 1.72 times higher.

• Journal of Internet Computing and Services
• /
• v.24 no.1
• /
• pp.87-97
• /
• 2023

Charger infrastructure facilities are designed and installed based on a constant power supply. Initially designed charging facilities support charging of rapidly growing electric vehicles on a limited power supply basis. In addition, current commercial vehicles can only be fully charged, and are supported by the rapid equalization charging method. However, commercial vehicles operate according to a set schedule, so flexible charging is essential. In this paper, we propose a power operation method with more than 20% efficiency improvement by using a fixed schedule-based charging scheduling and power distribution technique of a commercial bus based on the same amount of power in accordance with the rapid growth and increase of electric vehicles.

• Nuclear Engineering and Technology
• /
• v.55 no.8
• /
• pp.2812-2822
• /
• 2023

The supercritical carbon dioxide (sCO₂) Brayton power cycle is more effective than the conventional power cycle and is more widely applicable to heat sources. The inlet working conditions of the compressor have a higher influence on their operating performance because the thermophysical properties of the CO₂ vary dramatically close to the critical point. The flow in the sCO₂ compressor is simulated and the compressor performance is analyzed. The results show that the sCO₂ centrifugal compressor operates outside of its intended parameters due to the change in inlet temperature. The sCO₂ compressor requires more power as the inlet temperature increases. The compressor power is 582 kW when the inlet temperature is at 304 K. But the power is doubled when the inlet temperature increases to 314 K, and the change in the isentropic efficiency is within 5%. The increase in the inlet temperature significantly reduces the risk of condensation in centrifugal compressors. When the heat load of the sCO₂ power system changes, the inlet pressure to the turbine can be kept constant by regulating the rotational speed of compressors. With the increase in rotational speed, the incidence loss and condensation risk increase.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.2
• /
• pp.122-127
• /
• 2021

This paper produces CdS thin film using ITO glass as substrates. The MDS (Multiplex Deposition Sputter System) was used to produce devices by changing RF power and deposition time. The manufactured specimen was analyzed for its optical properties. The purpose of this paper is to find the fabrication conditions that can be applied to the photo-absorbing layer of solar cells. When RF power was 50W and deposition time was 10 minutes, the thickness was measured at 64Å. At 100W, the thickness was measured at 406Å and at 150 W, the thickness was measured at 889Å. Thin films were found to increase in thickness as RF power increased. As a result of the light transmittance measurement, 550-850nm was observed to have a transmittance of approximately 70% or more when the RF power was 50W, 100W, and 150W. Increasing RF power increased thickness and increased particle size, resulting in increased thin film density, resulting in reduced light transmittance. When RF power was 100W and deposition time was 15 minutes, the band gap was calculated at 3.998eV. When deposition time is 20 minutes, it is 3.987eV, 150W is 3.965eV at 15 minutes, and 3.831eV at 20 minutes. It was measured that the band gap decreased as the RF power increased. At XRD analysis, diffraction peaks at 2Θ=26.44 could be observed regardless of changes in RF power and deposition time. The FWHM was shown to decrease with increasing deposition time. And it was measured that the particle size increased as RF power was constant and deposition time was increased.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.4B
• /
• pp.275-280
• /
• 2002

Wireless communications have been developed time and time to satisfy more demands of users for internet service, mobile communication service and so on. One of infrastructures leading the next generation wireless communication is HAPS(High Altitude Platform Station). This paper analyzed outage probability when a mobile communication system was constructed by using HAPS. First, an approach to evaluate the carrier to interference power ratio' was introduced and results from the analysis were calculated and simulated. from the results, carrier to interference power ratio (C/I) and fading depth (K) had an effect on outage probability; outage probability decreases when K increases far constant C/I or C/l increases for constant K. In addition, when outage probability for a platform with elevation 30 degrees is expanded into it for 24-platforms, outage probability(C/I=9.8dB) was worse because of many interferers relatively.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.769-772
• /
• 2005

This paper describes a low-voltage and low-power channel selection analog front end with continuous-time low pass filters and highly linear programmable-gain amplifier(PGA). The filters were realized as balanced Gm-C biquadratic filters to achieve a low current consumption. High linearity and a constant wide bandwidth are achieved by using a new transconductance(Gm) cell. The PGA has a voltage gain varying from 0 to 65dB, while maintaining a constant bandwidth. A filter tuning circuit that requires an accurate time base but no external components is presented. With a 1-Vrms differential input and output, the filter achieves -85dB THD and a 78dB signal-to-noise ratio. Both the filter and PGA were implemented in a 0.18um 1P6M n-well CMOS process. They consume 3.2mW from a 1.8V power supply and occupy an area of $0.19mm^2$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.415.2-415.2
• /
• 2016

Triboelectric nanogenerator (TENG) is one of ways to convert mechanical energy sound, waves, wind, vibrations, and human motions to available electrical energy. The principal mechanism to generate electrical energy is based on contact electrification on material surface and electrostatic induction between electrodes. The performance of TENG are dependent on amount of the input mechanical energy and characteristics of triboelectric materials. Furthermore, the whole TENG system including mechanical structure and electrical system can effect on output performance of TENG. In this work, we investigated the effect of gear train on output performance and power conversion efficiency (PCE) of TENG under a given input energy. We applied the gear train on mechanical structure to improve the contact rate. We measured the output energy under a constant input energy by controlling the size of the working gear. We prepared gears with gear ratios (rin/rw) of 1, 1.7, and 5. Under the constant input energy, the voltage and current from our gear-based TENG system were enhanced up to the maximum of 3.6 times and 4.4 times, respectively. Also, the PCE was increased up to 7 times at input frequency of 1.5 Hz. In order to understand the effect of kinematic design on TENG system, we performed a capacitor experiment with rectification circuit that provide DC voltage and current. Under the input frequency of 4.5 Hz, we obtained a 3 times enhanced rectifying voltage at a gear ratio of 5. The measured capacitor voltage was enhanced up to about 8 fold in using our TENG system. It is attributed that our gear-based TENG system could improve simultaneously the magnitude as well as the generation time of output power, finally enhancing output energy. Therefore, our gear-based TENG system provided an effective way to enhance the PCE of TENGs operating at a given input energy.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.8
• /
• pp.1097-1103
• /
• 2012

There are many fish farms being cultivated in the southwestern cost of South Korea. Because the farms cultivating use the basic method that inflow and circulate sea-water, slight negligence and bad design cause major negative impact on fish deaths. Also, the optimal temperature for each specie of fishes has already been proven to differ on each specie. Maintaining this environment, regardless of seasons, is very difficult and that requires research to develop. In this paper, basic characteristics of heat and mechanism of heat transfer are studied. Based on this, Open-end water vessel is designed and constructed using sandwich-insulation panels and simulated to store the heat in certain isolated space. This study confirmed that it is possible to keep constant temperature by this method, in large areas of water where it is insulated by heat insulator. and equipped with heater in Open-end water vessel where the other part is heated. The AC power controller maintains the constant temperature required and the temperature controller detects and displays the temperature by using the micro-processor.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.6
• /
• pp.117-125
• /
• 1998

The paper attempts to estimate the incubation time of a cavity in the interface between a power law creep particle and an elastic matrix subjected to a uniaxial stress. Since the power law creep particle is time dependent, the stresses in the interface relax. The volume free energy associated with Helmholtz free energy includes strain energies caused by applied stress and dislocations piled up in interface(DPI). The energy due to DPI is found by modifying the result of Dundurs and Mura[4]. The volume free energies caused by both applied stress and DPI are a function of the cavity size(r) and elapsed time(t) and arise from stress relaxation in the interface. Critical radius $r^*$ and incubation time $t^*$ to maximise Helmholtz free energy is found in present analysis. Also, kinetics of cavity formation are investigated using the results obtained by Riede [7]. The incubation time is defined in the analysis as the time required to satisfy both the thermodynamic and kinetic conditions. Through the analysis it is found that 1) strain energy caused by the applied stress does not contribute significantly to the thermodynamic and kinetic conditions of a cavity formation, 2) in order to satisfy both thermodynamic and kinetic conditions, critical radius $r^*$ decreases or holds constant with increase of the time until the kinetic condition(eq. 2.3) is satisfied. there for the cavity may not grow right after it is formed, as postulated by Harris [15], and Ishida and Mclean [16], 3) the effects of strain rate exponent (m), material constant $\sigma$0, volume fraction of the particle to matrix(f)and particle size on the incubation time are estimated using material constants of the copper as matrix.

• International Journal of Safety
• /
• v.1 no.1
• /
• pp.36-42
• /
• 2002

This paper is aimed at predicting the life of rubber insulating gloves under normal operating stresses from relatively rapid test performed at higher stresses. Specimens of rubber insulating gloves are subject to multiple stress conditions, i.e. combined electrical and thermal stresses. Two modes of electrical stress, step voltage stress and constant voltage stress are used in specimen aging. There are two types of test for electrical stress in this experiment: the one is Breakdown Voltage (BDV) test under step voltage stress and thermal stress and the other is lifetime test under constant voltage stress and temperature stress. The ac breakdown voltage defined as the break-down point of insulation that leakage current excesses a limit value, l0mA in this experiment, is determined. Because the very high variability of aging data requires the application of statistical model, Weibull distribution is used to represent the failure times as the straight line on Weibull probability paper. Weibull parameters are deter-mined by three statistical methods i.e. maximum likelihood method, graphical method and least squares method, which employ SAS package, Weibull probability paper and FORTRAN, respectively. Two chosen models for predicting the life under simultaneous electrical and thermal stresses are inverse power model and exponential model. And the constants of life equation for multistress aging are calculated using numerical method, such as Gauss Jordan method etc.. The completion of life equation enables to estimate the life at normal stress based on the data collected from accelerated aging test. Also the comparison of the calculated lifetimes between the inverse power model and the exponential model is carried out. And the lifetimes calculated by three statistical methods with lower voltage than test voltage are compared. The results obtained from the suggested experimental method are presented and discussed.