• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.713-717
• /
• 2004

This is a thesis that a quarter-brick size of 100W class open-frame type on board power module comprising telecommunication application is reported. The input voltage is established between 36 and 75 in range in order for power module to be utilized for the telecommunication application, and output were set at 3.3V and 30A. A number of parts used for transformer, inductor, and hit sink are composed of PCB in order for DC-DC converter to be lowered below 8 mm. A constant current control circuit was annexed to the system as well as basic protection prototypes such as over-voltage, over-current, and over-temperature were well considered to enhance more credibility, and were tested. As a result, high circuit performance and credibility turned out to be significant.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1056-1059
• /
• 1996

In this paper, we analyzed the effect of the change of the rotor time constant on the performance of the indirect vector control system. By employing indirect field orientation technique, we have also suggested an optimal control algorithm that allows an induction motor to maintain the maximum torque under the changing environment of rotor time constant. A computer simulation on the transient response of the output torque was demonstrated. To verify the validity of the method that has been proposed in this paper, an experiment has been performed utilizing TMS32OC31(40MHz) DSP chip which is capable of performing floating-point arithmetic in real time.

• Journal of Industrial Technology
• /
• v.24 no.A
• /
• pp.91-97
• /
• 2004

This paper describes the design of a 2-phase stepping motor driver using CPLD(Complex Programmable Logic Device). The driver IC such as L297(SGS-Thomson Microelectronics), which is mostly used has some difficulties in PWM control because of the switching noise of power MOSFETs. It causes current ripple and acoustic noise. To improve theses characteristics, we proposed a new current control method that the output PWM frequency is almost constant using a digital filter. Also we proposed constant current method for 1-2 phase(half step) excitation. The proposed method is implemented with CPLD(Xilinx, XC9572-PC44). Experimental results show the effectiveness of the proposed method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.3
• /
• pp.280-289
• /
• 2015

A high-efficiency full-bridge DC-DC converter with a current-doubler rectifier and an asymmetric pulse-width modulation is proposed. Through the asymmetric pulse-width modulation, the proposed converter achieves zero-voltage switching of power switches without the circulating currents. The proposed converter reduces the output current ripple through the current-doubler rectifier. A control strategy is suggested for the proposed converter to charge battery banks. A constant current and constant voltage charging is performed. The proposed converter achieved a higher efficiency compared with the conventional full-bridge DC-DC converter with a phase-shift modulation. The performance of the proposed converter is evaluated by the experimental results for a 1.0 kW prototype circuit.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2467-2469
• /
• 1999

In this paper. the stability control system of constant output DC-DC converter is composed of considering a ripple source input and a transient variable sinusoidal power. Also, we design I-PD controller and add phase shift controller. Therefore, it is proposed controller that is stable about the input voltage and load alteration and tracking desired value.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03b
• /
• pp.9-9
• /
• 2010

The proton exchange membrane fuel cell (PEMFC) holds great promise of clean power. However, in practical applications which use the PEMFC as the power source, the output voltage from the fuel cell undergoes transient response especially during acceleration and deceleration. This paper presents the relationships between the internal voltage drop, voltage of time constant, time constant of FC1 and FC2 (in series and in parallel) charge curves and discharge curves respectively.

• ETRI Journal
• /
• v.42 no.3
• /
• pp.333-340
• /
• 2020

We consider a hybrid combiner design for downlink massive multiple-input multiple-output systems when there is residual inter-user interference and each user is equipped with a limited number of radio frequency (RF) chains (less than the number of receive antennas). We propose a hybrid combiner that minimizes the mean-squared error (MSE) between the information symbols and the ones estimated with a constant amplitude constraint on the RF combiner. In the proposed scheme, an iterative alternating optimization method is utilized. At each iteration, one of the analog RF and digital baseband combining matrices is updated to minimize the MSE by fixing the other matrix without considering the constant amplitude constraint. Then, the other matrix is updated by changing the roles of the two matrices. Each element in the RF combining matrix is obtained from the phase component of the solution matrix of the optimization problem for the RF combining matrix. Simulation results show that the proposed scheme performs better than conventional matrix-decomposition schemes.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.99-104
• /
• 2000

Calibration equation for Variable Temperature Anemometer(VTA) has been tested for measured velocity-output data and the calibration process has been compared with that of Constant Temperature Anemometer(CTA). VTA has greater sensitivity than that of any other conventional anemometers, but to be more popular technique in flow field measurement, simple, accurate and well established calibration process should be suggested. To meet this purpose, similar calibration method used for CTA has been adopted for VTA and finally calibration equation for VTA including the effect of temperature drift has been proposed.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.3
• /
• pp.275-281
• /
• 1990

This study suggests a new type shaft generator driven by hydraulic power suitable for small size vessels. Since the shaft generator system is very easy to be affected by disturbances such as speed variation of the main engine and the load variation of the generator, a robust servo control must be performed to obtain stable electric power with constant frequency. So, in this study the robust servo control method is adopted to the controller design. Dynamic characteristics on the frequency variations of the electric power output according to the disturbances are investigated by computer simulations. From the considerations of the computer simulation results, it is ascertained that the shaft generator system proposed in this study had good control performances.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.325-329
• /
• 1998

This paper describes the controller for the improving speed control of the AC servo motor. The microprocessor provides an output to the difference in command. the servo system improves the characteristics of speed control. When the motor is running at the same speed as set by the reference signal, the speed encoder also provides a signal of the same frequency. Thus, the microprocessor controlled digital techniques enable to realize the flexible performance and control which was possible with time constant of linear acceleration/deceleration. We can know that optimal speed of machining center is 75msec in 30000mm/min and actually, 75msec is using on machining center. Finally experimental results prove excellent performance of this control system. This can be reduced error with more exact measure of actual speed. The system can be adaptable to CNC machine.