• Journal of Power Electronics
• /
• v.15 no.1
• /
• pp.10-17
• /
• 2015

A quasi-constant on-time controlled buck front end in combined discontinuous conduction mode and boundary conduction mode is proposed to improve power factor (PF).When instantaneous AC input voltage is lower than the output bus voltage per period, the buck converter turns into buck-boost converter with the addition of a level comparator to compare input voltage and output voltage. The gate drive voltage is provided by an additional oscillator during distortion time to eliminate the cross-over distortion of the input current. This high PF comes from the avoidance of the input current distortion, thereby enabling energy to be delivered constantly. This paper presents a series analysis of controlling techniques and efficiency, PF, and total harmonic distortion. A comparison in terms of efficiency and PF between the proposed converter and a previous work is performed. The specifications of the converter include the following: input AC voltage is from 90V to 264V, output DC voltage is 80V, and output power is 94W.This converter can achieve PF of 98.74% and efficiency of 97.21% in 220V AC input voltage process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.830-833
• /
• 2004

Voltage step-down characteristics of Ring/Dot type piezoelectric transformer were examined with increasing input voltage from $10\;V_{pp}$ to $140V_{pp}$. Then the output load resistance was fixed to $125\;\Omega$. The voltage gain showed constant value till the input voltage of $70\;V_{pp}$. And then it linearly decreased till the input voltage of $140V_{pp}$. The output voltage of fabricated piezoelectric transformer increased with increasing input voltage. And driving frequencies when the output voltage was maximum value were changed according to input voltage. Frequency shifts and temperature rise of fabricated sample showed 2 kHz, $13^{\circ}C$, respectively when input voltage was changed from $10\;V_{pp}$ to $140V_{pp}$. Because of the temperature rise of fabricated piezoelectric transformer, the step-down characteristics of it was deteriorated above the input voltage of $70\;V_{pp}$.

• Journal of IKEEE
• /
• v.16 no.1
• /
• pp.34-44
• /
• 2012

This paper proposes a practical compensation method by using digital signal processing over the creep error which is representative in strain gauge loadcell. The signal compensation method carry out the simulation by deciding compensation constant (time constant) and coefficient measuring the loadcell output response. Then, compensation constant and coefficient are stored on the microprocessor. By using calculated on microprocessor creep error compensation values, weighting value is showed as a digital signal by reducing error values measured through output signals of loadcell. In addition, we apply error compensation method in order to have a dedicated software for loadcell electronic scale. This technique is useful because it has great influence on error rate reduction that has been produced by conventional electronic scales (0.03%). As a result our technique gives better accuracy (0.01%~0.003%) as what is given by digital electronic scale, while it has less complex operation processing.

• Transactions of the KSME C: Technology and Education
• /
• v.1 no.1
• /
• pp.129-138
• /
• 2013

Constant airflow should be kept in order to operate a constant-fired boiler of thermal power plants. Main Bearing Assembly Unit which rotates the ventilation fan does very important role to maintain constant airflow. However, the demand to the output of power is getting increased while the quality level of coal is getting worse than the initial level of design criteria. Especially cost wise operation considering increasing output and the difficulty to supply good quality coal drive increasing supply of low quality coal. As a result, the service life of Main Bearing Assembly is getting shorter till 2~3 years which is just a half of the life of original design. In this study, what causes to shorten the service life of Main Bearing Assembly Unit is analyzed through the reverse engineering and analysis and how to improve the service life more than two times to current situation is explained.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.1
• /
• pp.133-143
• /
• 1996

The constant modulus algorithm (CMA), one of the widely used blind equalization algorithms, equalizes channels using the second-order statistic of equalizer outputs. The performance of the CMA for multi-level signals such as the quadrature amplitude modulation (QAM) signal degrades because the CMA maps all signal power onto a single modulus. in this paper, to improve the equalization performance of a QAM system, we propose a shell partitioning method based on error magnitude. We assume the probability distribution of an equalizer output as Gaussian, and obtain decision boundaries by maximum likelihood estimation based on the fact that the distribution of the equalizer output power is noncentral $x^2$. The proposed CMA constructs a multi-moduli equlization system based on the fact that each shell separated by decision boundaries employs a single modulus. Computer simulation results for 32-QAM and 64-QAM show the effectiveness of the proposed algorithm.

• Journal of Advanced Navigation Technology
• /
• v.21 no.3
• /
• pp.220-229
• /
• 2017

In this paper, To take advantage a variety of DC power as the boost DC-DC converter design specifications through the inductor L and capacitor C through PSPICE to calculate the best estimate of the value. Boost DC-DC converter with a switch device using IRF840 and reverse recovery time Schottky diodes with excellent with constant current controller using D10SC6M and resistance can be configured to considering the Power LED Module was driven by the production. Converter's switching frequency is 50 kHz, the first Duty Rate was made to increase gradually depending on the value of the detection were, 10 % in the output voltage. As a result, the simulated Boost Power LED driver characteristics is in comparison with the design specifications, 5% or less as the error was approximated. Finally, when input 15 V were offered, a stable output 24 V were obtained. and Dimming Control through the adjustment of brightness and current consumption were possible.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.4
• /
• pp.127-133
• /
• 2013

This paper compare the performance of CCA (Compact Constellation Algorithm) adaptive equalization algorithm by effect of the compact slice weighting value for minimization of the intersymbol interference in the communication channel. The CCA combines the conventional DDA and RCA algorithm, it uses the constant modulus of the transmission signal and the considering the output of decision device by the power of compact slice weighting value in order to improving the initial convergence characteristics and the equalization noise by misadjustment in the steady state. In this process, it is confirmed by computer simulation that the compact slice weight affects the performance of CCA adaptive equalization algorithm. The performance index includes the output signal constellation, the residual isi and maximum distortion and MSE that is for the convergence characteristics, the SER according to the signal and noise power ratio at the channel is used. As a result of computer, it shows that the large weighting value gives more good in every performance index. But in SER performance, it is known that the small values gives more good in low SNR and the large values gives more good in high SNR.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.8
• /
• pp.45-51
• /
• 2008

HID(High Intensity Discharge) search lamp for shipment requires a high open circuit and output current compare than vehicle. This paper presents a soft-start open circuit voltage and constant current sequence control method for 2.5[kW] HID search lamp. The proposed method controls the opal circuit voltage and discharge current of HID lamp according to ignition signal with a simple 8-bit micro-processor and PWM device. For the stable control of lamp, micro-processor checks the output voltage and current. And the checked signals are compared with ignition signal and changes the control mode for stable operation. An ignition signal and micro-processor change the control mode from open circuit voltage contort to constant current control. The proposed control scheme is verified from experimental tests of 2.5[kW] HID search lamp for shipment.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.1
• /
• pp.86-92
• /
• 2016

Upon detecting a frequency event in a power system, the stepwise inertial control (SIC) of a wind turbine generator (WTG) instantly increases the power output for a preset period so as to arrest the frequency drop. Afterwards, SIC rapidly reduces the WTG output to avert over-deceleration (OD). However, such a rapid output reduction may act as a power deficit in the power system, and thereby cause a second frequency dip. In this paper, a hybrid reference function for the stable SIC of a doubly-fed induction generator is proposed to prevent OD while improving the frequency nadir (FN). To achieve this objective, a reference function is separately defined prior to and after the FN. In order to improve the FN when an event is detected, the reference is instantly increased by a constant and then maintained until the FN. This constant is determined by considering the power margin and available kinetic energy. To prevent OD, the reference decays with the rotor speed after the FN. The performance of the proposed scheme was validated under various wind speed conditions and wind power penetration levels using an EMTP-RV simulator. The results clearly demonstrate that the scheme successfully prevents OD while improving the FN at different wind conditions and wind power penetration levels. Furthermore, the scheme is adaptive to the size of a frequency event.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.5
• /
• pp.27-35
• /
• 2000

This paper deals with a control strategy for constant output power of SSRT(Soft Switching Resonant Type) FB(Full Bridge) DC-DC converter by an improved phase shift controller. When the FB DC-DC converter for the high density and the high effect control is operated in high speed switching, the switching loss and switching stress of the switching devices are increased. So, the soft switching method, which has the phase shift control with the digital I-PD controller, must be use in order to reduce its. And the output voltage that controlled by the digital I-PD controller tracks a reference without steady state error in variable input voltage. The validity of control strategy that proposed is verified from simulation results and experimental results by the DSP(TMS320C32).