• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.6
• /
• pp.112-119
• /
• 1995

Early fracture and cutting force of ceramic tool for hardened STC3 steel was investigated in this study. It was found that early fracture of ceramic tool was mostly occurred before normal wear was progressed beyond a critical cutting speed and normal wear was performed under the critical cutting speed. The relationships among critical cutting speed, which was a cause of early fracture, suggested cutting cross section, that is, maximum thickness of cut and width of cut, and cutting force were examined. The following conclusions were obtained: (1)Critical cutting speed showed a high value in the case of small maximum thickness of cut and large nose radius, but was not influenced by width of cut, (2)Principal, feed and radial force, respectively, showed the proportional value to constant cutting area, width of cut and maximum thickness of cut orderly, (3)Occurrence of early fracture was dependent upon radial force.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.5
• /
• pp.772-780
• /
• 1987

The normal and tangential belt forces for two types of flat belts are measured and compared. From friction theory, ti was assumed that tangential friction is proportional to the actual contact area $A_{a}$ and $A_{a}$ is proportional to normal pressure P; i.e., $A_{a}$ .var.P$^{n}$ . For a flat belt with cloth backing, the n=2/3 is obtained for the constant of belt surface model. For a flat belt with rubber backing, the n=0.9 to n=1.0 is suggested as a surface model constant. The theoretical equation developed in this paper showed agood with the experimental results.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.232-236
• /
• 1987

To improve the surface waviness in the peripheral milling, since the tool deflection is largely affected by cutting force, the feedrate is controlled so that the cutting force measured in the normal direction to the workpiece is constant. A discrete time first order model between the feedrate and the tool deflection is derived for the control. The experimental results show that the surface waviness is greatly improved by the proposed method.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.16 no.3
• /
• pp.181-192
• /
• 2012

Here in this paper, the steady paint film flow on a vertical wall of a non-Newtonian pseudo plastic fluid for drainage problem has been investigated. The exact solution of the nonlinear problem is obtained for the velocity profile. Also the average velocity, volume flux, shear stress on the wall, force to hold the wall in position and normal stress difference have been derived. We retrieve Newtonian case, when material constant ${\mu}_1$ and relaxation time ${\lambda}_1$ equal zero. The results for co-rotational Maxwell fluid is also obtained by taking material constant ${\mu}_1$ = 0. The effect of the zero shear viscosity ${\eta}_0$, the material constant ${\mu}_1$, the relaxation time ${\lambda}_1$ and gravitational force on the velocity profile for drainage problem are discussed and plotted.

• Tribology and Lubricants
• /
• v.20 no.3
• /
• pp.125-131
• /
• 2004

Nano-wear behavior of amorphous carbon films was studied by Atomic Force Microscopy. The a-C films are deposited on Si(100) substrate by DC magnetron sputtering method. The influences of different surface roughness on the nano-wear are investigated. Nano-wear tests were carried out using a very sharp diamond coated tip. Its spring constant was 1.6 N/m and radius of curvature was 110 nm. Normal force used in the wear tests ranged 0 to 400 nN. It was found that surface depression occurred during scratching because of plastic deformation and abrasive wear (cutting St ploughing). Wear depth increased linearly with normal force. Changing the surface roughness variables according to the bias pulse control, the less surface roughness decreased the wear depth. The thickness did not affect the wear resistance.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.131-134
• /
• 1991

In order to determine an operating pattern of SLIM in an experimental MAGLEV vehicle, operating characteristics of SLIM are obtained using a disk type test facility. The test results are compared with the pre-estimated values. It is found that a closed loop control is required for operating at a constant slip-frequency condition which makes the normal force minimum.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.135-138
• /
• 1991

In this study, a variety of characteristics is considered when LIM for transit is driven with acceleration and deceleration. From the characteristics of constant voltage, with V/f ratio fixed, slip frequency is derived. With slip frequency of 12[Hz] and objective velocity of 40[km/h], the robust control characteristics which are generated constant thrust and normal force, except for open-loop control interval, are obtained.

• Journal of computational fluids engineering
• /
• v.4 no.2
• /
• pp.9-16
• /
• 1999

The present study investigates flow character and heat transfer behaviors of viscoelastic non-Newtonian fluid in a 2:1 rectangular duct. An axially-constant heat flux on bottom wall and peripherally constant temperature boundary condition(H1) was adopted. The Reiner-Rivlin fluid model is used as the normal stress model for the viscoelastic fluid and temperature-dependent viscosity model is adopted. The present results show a signifiant change of the main flow field which causes a large heat transfer enhancement. This phenomena can be explained by the combined effect of buoyancy, temperature-dependent viscosity and viscoelastic property on the flow.

• Proceedings of the KIEE Conference
• /
• 2009.04b
• /
• pp.58-60
• /
• 2009

This paper deals with force characteristic analysis of linear switched reluctance motor using dynamic simulation. First, we calculated flux density of linear switched reluctance motor according to position. Second, analyzed normal force from flux density of linear switched reluctance motor according to position. Also, analysis result compares with data that is derived through a finite element analysis, and proved validity. However, linear switched reluctance motor has non linear characteristic, hence, analysis of propulsion force do not easy using analytical method. Therefore, we presented dynamic characteristic analysis model which is consisted at motor and sensor signal part, etc., and substitute circuit constant that get using magnetic equivalent circuit method, we confirmed propulsion force.

• Journal of Power System Engineering
• /
• v.17 no.4
• /
• pp.86-93
• /
• 2013

This paper deals with the effects of driving force and material properties on statistical distribution of fatigue crack growth rate (FCGR) for the friction stir welded joints of Al 7075-T651 aluminum plate. In this work, the statistical probability distribution of fatigue crack growth rate was analyzed by using our previous constant stress intensity factor range controlled fatigue crack growth test data. As far as this study are concerned, the statistical probability distribution of fatigue crack growth rate for the friction stir welded (FSWed) joints was found to evaluate the variability of fatigue crack growth rate for base metal (BM), heat affected zone (HAZ) and weld metal (WM) specimens. The probability distribution of fatigue crack growth rate for FSWed joints was found to follow well log-normal distribution. The shape parameter of BM and HAZ was decreased with increasing the driving force, however, the shape parameter of WM was decreased and increased with increasing the driving force. The scale parameter of BM, HAZ and WM was increased with the driving force.