• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.624-627
• /
• 2000

This paper describes a local modification capability on shell meshes, which can change a 'constant or variable radius of rounding for the s h q edges of the stamping die shoulder in the mesh. The algorithm consists of the followin_e three main steps; (1) the rounding area for sharp edges of a die shoulder are detected from the given shell mesh, (2) a rolling-ball surface with a given constant or variable radius is generated, which is contacti% with two incident face groups of the sharp edges, (3) the rounding area of the mesh is cut off, and a new mesh for the rolling-ball surface is generated and implanted into the gap. Owing to this rounding modification capability, CAE engineers can examine various cases based on the existing dies by scanning them to form polyhedral models and then changing radii of die shoulders for stamping process simulation.

• Journal of Korea Foundry Society
• /
• v.8 no.4
• /
• pp.429-436
• /
• 1988

The influences of some casting conditions on bonding ratio and state at bonding zone of stainless steel-cast iron dual tube produced by centrifugal casting process were investigated to estimate fabrication technics. 1) Bonding ratio is increasing such as increasing of inner surface temperature of outer metal(stainless steel STS 304), if pouring temperature of inner metal (cast iron) is constant. 2) The more pouring temperature of inner metal (cast iron) increase, the more bonding ratio increase when inner surface temperature of outer metal (cast iron) is constant. 3) As the mold rotary speed is increase, the hatching area of bonding map (perfect bonding area) goes down to the low pouring temperature of inner metal. 4) In order to predict bonding state of two different metal, we are able to make and use the bonding map about casting conditions such as inner surface temperature of outer metal, pouring temperature of inner metal and mold rotary speed.

• Applied Chemistry for Engineering
• /
• v.5 no.1
• /
• pp.105-113
• /
• 1994

The amount of nitrogen gas adsorbed by Spherocarb and Sucrose Char was measured as a function of the relative pressure with temperature being kept constant at 77 to 184K. Isotherms at different temperatures were obtained by keeping the adsorbent at a constant temperature using liquid nitrogen, iso-pentane, n-pentane, ethyl alcohol, and iso-propyl alcohol slush baths. The objective for this study is to provide information on the specific surface area and pore volume by analyzing the experimental data using adsorption models such as the Brunauer-Emmett-Teller and Dubinin-Radushkevich models.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.10
• /
• pp.113-119
• /
• 1998

Ship structures and aircraft structures are consisted of thin sheet alloy, so it is very important to understand the characteristics of fatigue crack propagation of that material and to establish the data base. The data for fatigue crack propagation behavior scatter very much even under identical experimental conditions with constant loading. The behavior of fatigue crack propagation under regular and irregular cyclic loadings is known to be highly affected by complicated factors such as plastic zone developed at the vicinity of crack tip and reduction of cross sectional area. In this paper, the controlled stress amplitude and overload fatigue crack propagation tests have been conducted to investigate the effect of varying factors such as plastic zone size near the crack tip and area reduction factor (AF) on the fatigue crack propagation behavior A better simulation of fatigue crack propagation behavior is found to be obtainable by using Wheeler and Willenborg models with AF effect.

• International Journal of High-Rise Buildings
• /
• v.6 no.1
• /
• pp.91-99
• /
• 2017

Special consideration should be given to differential column shortening during the design and construction of a tall building to mitigate the adverse effects caused by such shortening. The effects of the outrigger - which is conventionally used to increase the lateral stiffness of a tall building - on the differential shortening are investigated in this study. Three analysis models, a constant-section, constant-stress, and general model, are prepared, and the differential shortenings of these models with and without the outrigger are compared. The effects of connection time, sectional area, and location of the outrigger on the differential shortening are studied. The sectional area of the outrigger shows a non-linear relation in reducing the maximum differential shortening. The optimum locations of the single and dual outriggers are investigated by an exhaustive search method, and it is confirmed that a global optimum location exists. This study shows that the outrigger can be utilized to reduce the differential shortening between the interior core wall and the perimeter columns as well as to reduce the lateral displacements due to wind or earthquake loads.

• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.104-105
• /
• 2013

When actual IPMSM is driving, it is difficult to figure out the correct current during the current control period due to the operation speed limit of digital signal processing. Therefore, in order to control IPMSM for electric vehicle efficiently, we should design 2D Look-up Table to find out optimal current reference corresponding to speed and torque of IPMSM. This paper explains the design method of 2D Look-up Table for optimal current control of constant torque area and constant output area of IPMSM for electric vehicle. Finally, experimental results are presented to verify the reliability of 2D Look-up Table.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.185-189
• /
• 2003

The purpose of this study is to obtain the optimal operating condition of conduction cooled taper shape high-temperature superconductor (HTS) current lead operated in current sharing mode. In our previous study, we discovered that the optimal operating condition of constant cross-section area HTS current lead is in the current sharing state, and in optimal condition, the temperature gradient at warm end is not zero. The analysis result of taper HTS current lead is quiet similar to the constant area HTS current lead. The minimum dissipation of taper HTS current lead is not influenced by taper angle, however the optimal operation condition is varied with taper angle.

• Communications of the Korean Mathematical Society
• /
• v.34 no.3
• /
• pp.841-854
• /
• 2019

In this article, a subclass of univalent harmonic mapping is introduced by restricting its analytic part to lie in the class $S^{\delta}[{\alpha}]$, $0{\leq}{\alpha}<1$, $-{\infty}<{\delta}<{\infty}$ which has been introduced and studied by Kumar [17] (see also [20], [21], [22], [23]). Coefficient estimations, growth and distortion properties, area theorem and covering estimates of functions in the newly defined class have been established. Furthermore, we also found bound for the Bloch's constant for all functions in that family.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.10
• /
• pp.1269-1278
• /
• 2013

The cutting area changes periodically in the end-milling process because of its form generation mechanism. In this study, the effects of the cutting area on end-milled side walls are studied by developing a cutting area model that simulates the area formed by engagement between a workpiece and a cutting edge of the end mill. To do this, the straightness profile of the side wall in the axial direction is investigated. Models for estimating the cutting area and the transition point, where the slope of the straightness profile changes suddenly, are verified from real end-milling experiments under various radial and axial depth of cut conditions. Through this study, it is confirmed that the final end-milled side wall is generated in the regions where cutting areas are constant and decreasing in the down-cut. Similarly, in stable up-cut, it is also generated in the regions where cutting areas are increasing and constant. It is found that the transition point appears when the region changes.

• Journal of Soil and Groundwater Environment
• /
• v.19 no.3
• /
• pp.39-46
• /
• 2014

Hydraulic conductivity is an important parameter, representing permeable property of the groundwater in aquifers, in the issues of groundwater development, groundwater contamination, and groundwater flow, etc. We estimated a relationship between hydraulic conductivity and electrical properties (formation factor, chargeability, and time constant) of silty sand in the laboratory. For this study, we conducted grain size analysis, constant head permeameter test, and measured electrical resistivity and spectral induced polarization of silty sand samples collected from the riverside alluvium of the Nakdong River in Nogok-ri area, Dasan-myeon, Goryeong-gun in Gyeongbook Province, Korea. In the laboratory test, we used soil samples of approximately uniform porosity with 0.5% error range, and kept the electrical resistivity of pore water with 100 ohm-m. As a result, the relationship between effective particle size and hydraulic conductivity agrees fairly well with the existing empirical formulas. Hydraulic conductivity was correlated with formation factor, chargeability, and time constant: hydraulic conductivity increased with increasing formation factor and time constant as well as with decreasing chargeability.