• Journal of Advanced Marine Engineering and Technology
• /
• 제22권5호
• /
• pp.693-701
• /
• 1998

This study presents result of comparison between two other numerical method method of char-acteristics(MOC) and Lax-Wendroff method(LWM) applied at wave action analysis of intake and exhaust pipe in terms of calculated pressure velocity and emitted noise in the time and the fre-quency domain by means of fast Fourier transform analysis. Particularly FCT(Flux Corrected Transport)scheme is appended to LWM to protest unaceptable overshoots occurring near discon-tinuity. The final conclusion of this study is that MOC should be replaced by a second order finite difference approach because of larger contributions due to high frequency components than the results from the method of characteristics. Clear benefits we can get by change are faster calcula-tion higher accuracy conservation of mass and consistent calculation method.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제32회 추계학술대회 정기총회
• /
• pp.243-249
• /
• 2000

In case of the limitation of Deep RIE fabrication for Micro Gas Turbine, bearing aspect ratio is limited in very small value. The characteristics such as pressure distribution load capacity and non-linearity of a short bearing of L/D=0.083 and a conventional bearing of L/D=1.0 with coupled boundary effects are investigated far Micro Gas Tlubine bearings. The coupled efffect was analyzed by mass conservation at coupled end area. The results, increasing load capacity and non-linearity due to the coupled effect of thrust and journal bearing, are obtained and the selection of journal bearing type is discussed.

• KSTLE International Journal
• /
• 제1권2호
• /
• pp.107-112
• /
• 2000

In case of the limitation of Deep RIE fabrication far Micro Gas Turbine, bearing aspect ratio is limited in very small value. The characteristics such as pressure distribution, load capacity and non-linearity of a short bearing of L/D=0.083 and a conventional bearing of L/D=1.0 with coupled boundary effects are investigated for Micro Gas Turbine bearings. The coupled effect was analyzed by mass conservation at coupled end area. The results, increasing load capacity and non-linearity due to the coupled effect of thrust and journal bearing, are obtained and the selection of journal bearing type is discussed.

• Journal of Mechanical Science and Technology
• /
• 제14권5호
• /
• pp.569-581
• /
• 2000

A cycle simulation program is developed and its predictions are compared with the test bed measurements of a direct injection (DI) diesel engine. It is based on the mass and energy conservation equations with phenomenological models for diesel combustion. Two modeling approaches for combustion have been tested; a multi-zone model by Hiroyasu et al (1976) and the other one coupled with an in-cylinder flow model. The results of the two combustion models are compared with the measured imep, pressure trace and NOx and soot emissions over a range of the engine loads and speeds. A parametric study is performed for the fuel injection timing and pressure, the swirl ratio, and the squish area. The calculation results agree with the measured data, and with intuitive understanding of the general operating characteristics of a DI diesel engine.

• 대한기계학회논문집B
• /
• 제29권11호
• /
• pp.1173-1181
• /
• 2005

The cooling effect of a mobile phone using PCM(Phase Change Material) module has been numerically investigated. A transient three-dimensional numerical analysis of heat and fluid flow with natural convection is performed in this study. Governing conservation equations for mass, momentum and energy are solved by an implicit finite volume method. An enthalpy-porosity technique has been used for modeling of the melting process. Two different ways of placing the PCM module are considered. One is to place a PCM module between the substrate and battery pack, and the other is to place a PCM module between MCM(multichip module) and battery pack. Three different types of PCMs are used to predict the performance of PCM. The results show that passive cooling with PCM can reduce the temperature rise and the effect of natural convection in PCM module considered in this study is negligible.

• 대한설비공학회지:설비저널
• /
• 제17권5호
• /
• pp.583-589
• /
• 1988

Condensation of water vapor into an absorbent liquid of LiBr-water solution falling over a bank of water cooled horizontal tubes was investigated theoretically. The governing conservation equation for a re-defined physical transport phenomena were solved numerically using a finite difference method. Raw parameters were used in this study, since reliable experimental data is required prior to a dimensionless parametric study. The average values of wall heat transfer coefficient and interfacial absorption rate were defined to see the system performance. Other parameters include tube diameter, streamwise coordinate (and number of tubes in row), mass flow rate, and the wall temperature. The effects of these quantities on the absorption processes and suggestions for a rational system design have been presented.

• 한국결정성장학회지
• /
• 제13권4호
• /
• pp.187-198
• /
• 2003

Zinc selenide (ZnSe) single crystals hold promise for many electro-optics, acousto-optic and green laser generation applications. This material is prepared in closed ampoules by the physical vapor transport (PVT) growth method based on the dissociative sublimation. We investigate the effects of diffusive-convection on the crystal growth rate of ZnSe with a low vapor pressure system in a horizontal configuration. Our results show that for the ratios of partial pressures, s=0.2 and 2.9, the growth rate increases with the Peclet number and the temperature differences between the source and crystal. As the ratio of partial pressures approaches the stoichiometric value of 2, the rate increases. The mass fluk based on one dimensional (1D model) flow for low vapor pressure system fall within the range of the predictions (2D model) obtained by solving the coupled set of conservation equations, which indicates the flow fields would be advective-diffusive. Therefore, the rate and the flow fields are independent of gravity acceleration levels.

• 한국항만학회지
• /
• 제5권2호
• /
• pp.65-75
• /
• 1991

Tidal current and water level change in coastal waters are formulated in terms of mathematical models. A systematic discussion of the derivation of a set of governing equations, expressing conservation of mass and momentum is presented. A simplification is introduced by integrating all variables and equations over the total water depth, the Solution of the formulated problem is achieved by using the finite difference method(FDM). The applied study area is taken from Mokpo harbor and its adjacent coastal water which have significant hydrographical changes due to the construction of the estuary barrage and land reclamation work of estuary barren. Some comparisons with the observed current and water level changes the numerical solutions are found to be considerably fit well for the recent coastal water motion.

• 설비공학논문집
• /
• 제17권3호
• /
• pp.243-249
• /
• 2005

The present study has been conducted to simulate dynamics of a gas engine-driven heat pump(GHP) for design of control algorithm. The dynamic modeling of a GHP was based on conservation laws of mass and energy. For automatic control of refrigerant pressures, actuators such as engine speed, outdoor fan, coolant three-way valves and liquid injection valve were PI or P controlled. The simulation results showed physical behavior that is realistic enough to apply for control algorithm design.

• 설비공학논문집
• /
• 제27권7호
• /
• pp.362-368
• /
• 2015

This paper presents a numerical study on the performance of a vapor compression cycle equipped with an ejector as an expansion device to improve the COP by reducing the expansion loss and compressor work. The simulation is carried out using a model based on the conservation of mass, energy and momentum in the ejector. From the results of the simulation, the vapor compression cycle equipped with an ejector showed a maximum COP improvement of 14.0% when using R134a refrigerant and 16.8% when using R1234yf. In addition, the performance of the system with an ejector represents the increased performance as the temperature difference between condensing and evaporating increased.