• 건축역사연구
• /
• 제21권3호
• /
• pp.7-28
• /
• 2012

This study is intended to Mindori structure which is general private houses' structural type among traditional types and is a basic study to confirm structural characteristics of Hwatong connection which is general connection type of column-beam-cross beam. It is aimed to analyze how main member, column, such as size, figure, thickness of Sungetuk and Dugeup affect on structure. Following conclusions are drawn. 1. According to connection conditions, models with big coefficient of friction show stable hysteretic behavior until the angle rotation of member reaches 1/60 and models with small coefficient of friction show dramatical increase in load after the angle rotation of member reaches 1/24. After the angle rotation of member reaches 1/30, separation distance of members is identified physically and cracks are not observed. 2. Specimens with big coefficient of friction show similar inner force regardless of column size(except column size 150mm) and models with small coefficient of friction show increasing inner force as the column size increases. Specimens with same sectional area have similar inner force even though the column figures are different. The thickness of Sungetuk and Dugeup doesn't affect inner force greatly, however, when the thickness of Sungetuk is thin, it could lead to failure of structure as it breaks. 3. The bigger the size of column and the coefficient of friction are, the smaller Bending stiffness depreciation ratio is. 4. Energy Dissipation Efficiency differs from the coefficient of friction. When the coefficient of friction is big, square column shows bigger than round one and it is bigger when the thickness of Sungetuk and Dugeup is thicker. When the coefficient of friction is small, round column shows bigger than square one.

• Steel and Composite Structures
• /
• 제23권4호
• /
• pp.453-464
• /
• 2017

The square tubed-reinforced concrete (TRC) column is a kind of special concrete-filled steel tube (CFST) columns, in which the outer thin-walled steel tube does not pass through the beam-column joint, so that the longitudinal steel reinforcing bars in the RC beam are continuous through the connection zone. However, there is a possible decrease of the axial bearing capacity at the TRC column to RC beam connection due to the discontinuity of the column tube, which is a concern to engineers. 24 connections and 7 square TRC columns were tested under axial compression. The primary parameters considered in the tests are: (1) connection location (corner, exterior and interior); (2) dimensions of RC beam cross section; (3) RC beam type (with or without horizontal haunches); (4) tube type (with or without stiffening ribs). The test results show that all specimens have relatively high load-carrying capacity and satisfactory ductility. With a proper design, the connections exhibit higher axial resistance and better ductility performance than the TRC column. The feasibility of this type of connections is verified.

• 한국재난정보학회 논문집
• /
• 제18권1호
• /
• pp.1-9
• /
• 2022

연구목적: 본 연구에서는 토목섬유 연직차수시스템에 사용되는 팽창 지수재를 사용하여 지수재의 팽창에 따른 차수성능을 평가하였다. 연구방법: 토목섬유 연직차수 공법 적용시 연결부에 대한 투수능을 판단하기 위하여 ASTM D5887과 ASTM D6766을 준용하였다. 팽창 지수재를 각 용액에 포화시킨 후 시간경과에 따른 무게, 두께, 부피 변화를 분석하였으며, 토목섬유 연직차수벽 연결부에 팽창지수재를 설치하여 투수 특성을 평가하였다. 연구결과: 염수조건에서 지수재의 팽창반응 시간이 상대적으로 늘어남에 따라 투수능의 저하도 담수에서 보다 작은 감소폭을 나타내었다. 또한 토목섬유 연직차수재료의 결속 방법에 따라 롤 이음방식이 인터록 방식 보다 수두차에 의한 압력저항이 커서 차수성능이 다소 우수하게 나타났다. 결론: 주유소, 유류저장시설 및 산업단지 등 오염물의 유출을 추정할 수 있는 도심지 오염원에서는 오염물질 확산을 방지할 수 있는 사전대응 기술이 피해규모를 현격하게 감소시킬 수 있다.

• 한국전산구조공학회논문집
• /
• 제28권1호
• /
• pp.93-100
• /
• 2015

현대 목조 구조물은 일반적으로 접합철물인 연결재를 이용하여 접합된다. 그리고 목조 구조물에서 다수의 연결재를 사용한 접합부는 반강접 접합부를 만든다. 목조 구조물에 접합부가 핀접합으로 설계될 경우에 접합부를 통해 전달되는 하중이 과소 평가되고 이것은 접합부의 저항능력 부족을 초래한다. 목조 구조물의 접합부를 완전 강접합으로 고려할 경우에 접합에 필요한 접합철물의 양이 과도하게 증가 할 수 있다. 이것은 미적인 요소 뿐만 아니라 시공성과 경제성을 저하시킨다. 접합부의 합리적인 강성에 대한 추정은 목조 구조물의 합리적인 접합부의 설계에 필수적인 요소이다. 이 논문은 목조 구조물의 구조설계를 쉽게 수행할 수 있도록 도움을 주기 위하여 2면 전단접합에 대하여 구조설계에서 널리 이용되는 상용 프로그램을 사용하여 접합부의 근사적인 강성을 나타낼 수 있는 해석 모델링 기법을 제안한다. 제안된 근사해석 모델링 기법은 휨 모멘트, 인장에 대한 실험 결과와 해석결과를 비교하여 접합부의 거동을 나타낼 수 있다는 것을 확인하였다.

• 콘크리트학회논문집
• /
• 제26권4호
• /
• pp.545-553
• /
• 2014

이 연구는 PC 보-기둥 접합부의 일반적인 거동의 접합 상세에 따른 통합적 평가 방안을 제안하였다. 이 연구는 접합부의 파괴 패턴과 이에 연관된 접합부 상세의 특징을 정량적으로 표현하기 위해 접합부와 각 요소들이 보유한 변형기여분을 사용할 것을 제안하였다. 이에 따라 PC 접합부는 '일체식 접합부'와 '연결식 접합부'로 크게 분류되었다. 접합부의 분류를 위한 기준 사항의 제안 및 검증을 위해 네 개의 보-기둥 실험체의 실험을 수행하였다. 실험은 일반적인 보-기둥 접합부의 실험 방법과 같은 방법으로 진행되었다. 가력은 접합부 상부 기둥의 끝단에서 수행되었으며, 보 양단은 힌지로 고정되었다. 변형기여분의 평가를 위해 총 34개의 LVDT가 주요 변형이 발생할 것으로 예상되는 곳에 설치되었다. 실험 결과 세 개의 실험체에서 나타난 각 요소들의 변형기여분은 수치적으로 다른 특성을 가지고 있는 것을 확인할 수 있었다. 실험 결과를 기반으로 접합부의 변형 정도와 다른 요소들의 변형 정도에 의거하여, 접합부의 변형이 적고 보의 휨 변형이 크게 나타나는 강한 접합부와 접합부의 변형이 용인되는 연성 접합부로 일체식 접합부를 분류할 수 있었다.

• 대한치과보철학회지
• /
• 제46권6호
• /
• pp.561-568
• /
• 2008

STATEMENT OF PROBLEM: Currently, many implant systems are developed and divided into two types according to their joint connection: external or internal connection. Regardless of the connection type, screw loosening is the biggest problem in implant-supported restoration. PURPOSE: The purpose of this study is to assess the difference in stability of abutment screws between the external and internal hexagonal connection types under cyclic loading. MATERIAL AND METHODS: Each of the 15 samples of external implants and internal abutments were tightened to 30 N/cm with a digital torque gauge, and cemented with a hemispherical metal cap. Each unit was then mounted in a $30^{\circ}$ inclined jig. Then each group was divided into 2 sub-groups based on different periods of cyclic loading with the loading machine (30 N/ cm - 300 N/cm,14 Hz: first group $1{\times}10^6$, $5{\times}10^6$ cyclic loading; second group $3{\times}10^6$, $3{\times}10^6$ for a total cyclic loading of $6{\times}10^6$) The removal torque value of the screw before and after cyclic loading was checked. SPSS statistical software for Windows was used for statistical analysis. Group means were calculated and compared by ANOVA, independent t-test, and paired t-test with ${\alpha}$=0.05. RESULTS: In the external hexagonal connection, the difference between the removal torque value of the abutment screw before loading, the value after $1{\tims}10^6$ cyclic loading, and the value after $1{\times}10^6$, and additional $5{\times}10^6$ cyclic loading was not significant. The difference between the removal torque value after $3{\times}10^6$ cyclic loading and after $3{\times}10^6$, and additional $3{\times}10^6$ cyclic loading was not significant. In the internal hexagonal connection, the difference between the removal torque value before loading and the value after $1{\times}10^6$ cyclic loading was not significant, but the value after $1{\times}10^6$, and additional $5{\times}10^6$ cyclic loading was reduced and the difference was significant (P < .05). In addition, in the internal hexagonal connection, the difference between the removal torque value after $3{\times}10^6$ cyclic loading and the value after $3{\times}10^6$, and additional $3{\times}10^6$ cyclic loading was not significant. CONCLUSION: The external hexagonal connection was more stable than the internal hexagonal connection after $1{\times}10^6$, and additional $5{\times}10^6$ cyclic loading (t = 10.834, P < .001). There was no significant difference between the two systems after $3{\times}10^6$, and additional $3{\times}10^6$ cycles.

• 한국실내디자인학회논문집
• /
• 제25권2호
• /
• pp.92-100
• /
• 2016

Recently, new detached houses on a small plot in low-rise residential urban area have attracted more public interests than ever before. This study aims to categorize basic types of interior plans in small urban detached houses by analyzing the layouts of the public space(LDK) within them which are popular in Japan. The results of this study may be summarized as follows. Unit floor plans were basically classified as 16 types according to the layout of LDK. Among these, the LDK type in a straight line shows the most at 28.9%. Again, these plans were sub-classified into 38 types by plan composition. The new 'LDKL' (a new term the authors propose to be used) type was observed in cases where K was directly connected to L. This type appears at 9 out of 38 types. In the connection of LDK, the LDK type shows the most at 60.8%; secondly the L-DK type at 29.9%; thereafter the LD-K type at 6.2%; and lastly L-D-K type, the least frequently at 1.0%. The cases of inter-level connection between LDK and the surrounding space were observed in various cases such as the open workplace of the upstairs hallway visually connected with LDK through the void space and as the attic space of the pitched roof visually linked to it.

• 한국안전학회지
• /
• 제27권4호
• /
• pp.50-61
• /
• 2012

In recent years, various research and developments to introduce composite bridges of new concept have been performed. The types of integral bridge and portal rigid frame bridge are having advantages in bridge maintenance and structural efficiency by eliminating expansion joints and bridge supports. However, the detail of typical girder-abutment connection has problems such as complexity of construction and increase of the construction cost. A new type of bridge, called prestress integral composite girder(PIC girder) bridge, is proposed in this study, which decreases the cost of construction and improves the efficiency of construction by simplifying the detail of construction for girder-abutment connection. PIC girder bridge has the connection detail in which the steel girder and the abutment are integrated by using the PS bar installed in the connection. In this study, finite element analysis and mock-up load test are conducted to evaluate the propriety of design, the effective of fabrication and structural safety for PIC girder bridge. The adequacy of the PIC giredr bridge is verified by the results of static/dynamic load test and finite element analyses.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제1권2호
• /
• pp.70-78
• /
• 2012

Due to the variable nature of renewable energy resources and power demand by consumers, it is difficult to operate a power system installed with only one type of renewable energy resource. Grid-based renewable generation may be the only solution to overcome this problem. The conventional approach based on a low-voltage converter with power frequency transformer is commonly employed for grid connection of offshore renewable energy systems. Because of the heavy weight and large size of the transformer, the system can be expensive and complex in terms of installation and maintenance. In this paper, an 11-kV series connected H-bridge (SCHB) multilevel voltage source converter (VSC) is proposed to achieve a compact and light direct grid connection of renewable energy systems. This paper presents the design, simulation and analysis of a five level (5L)-SCHB and an eleven level (11L)-SCHB VSC for 11-kV grid-based renewable energy systems. The performance, cost, modulation scheme and harmonic spectra of the converter are analyzed.

• 한국강구조학회 논문집
• /
• 제27권3호
• /
• pp.299-310
• /
• 2015

일반적인 CFT구조는 구조적 거동이 우수함에도 불구하고 폐단면으로 인한 제작 및 가공의 번거러움, 충전성 등의 문제를 가지고 있다. 이 연구는 CFT구조의 충전성을 개선한(보의 상플랜지에는 관통다이아프램, 하플랜지에는 외측다이아프램을 적용) 기둥-단순보의 접합부에서 외측 다이아프램의 치수에 따른 구조적 거동을 살펴보았다. 변수해석을 실시하여 EP-T 타입 접합부내력 영향을 주는 이유를 찾았다. 결과적으로 원형CFT기둥-보접합부에 대한 실험 및 해석을 통하여 원형 CFT구조의 구조적 거동을 조사했다.