• 콘크리트학회논문집
• /
• 제21권2호
• /
• pp.159-168
• /
• 2009

본 연구에서는 기존의 연구방법을 개선한 프리스트레스가 도입된 아라미드 스트랩으로 횡 구속된 RC 원형기둥의 일축압축 거동에 대하여 강도와 변위에 의한 강성 및 구속효과에 대하여 연구하였으며, 그 프리스트레싱 보강방법 및 과정에 대하여 비교적 상세히 소개하였다. 이 방법으로 보강된 기둥의 파괴형태는 초기 능동 구속압의 작용으로 인하여 변위 증가율이 매우 낮으며 이후 최종 파괴시까지도 그 형상이 유지되는 매우 안정적인 파괴형태를 보이게 된다. 파괴하중 비교 결과 일반 RC 기둥과 비교하여 73% 이상 강도증진 효과를 나타내었다. 또한 변형 증가율이 매우 작으며 이로 인한 변위구속효과가 매우 우수함을 확인할 수 있었다. 기존의 보강방법 (CFS, GFS)과의 비교를 통하여, 상대적으로 작은 면적으로 우수한 강도증진을 보이며 강성증가로 인한 구속효과 역시 우수하며 체적 증가율도 팽창하지 않는 결과를 보였다. 특히, 콘크리트 팽창 이후부터 발휘되는 기존 방법의 구속효과와는 달리, 초기부터 도입되는 프리스트레스트 긴장력에 의한 초기변형 구속효과가 매우 탁월하며, 최종 파괴시까지 체적 변형률이 팽창하지 않는 안정적인 결과를 나타낸다.

• 한국방재학회 논문집
• /
• 제5권2호
• /
• pp.57-63
• /
• 2005

일반적인 구조물의 경우 사용하중 상태에서 지반이 경험하는 변형율 범위는 1% 미만이고 대부분의 지반이 0.01% 이하의 저변형율 거동을 나타내는 것으로 알려졌다. 본 연구는 불포화 화강풍화토의 저변형율에서의 동적 거동에 미치는 영향을 고찰하기 위하여 수원지역의 시료를 사용하여 간극비 및 구속응력을 달리하고 그에 따른 포화도별로 공진주시험을 시행하여 다음과 같은 결론을 얻었다. 감쇠비의 최소값은 최대전단탄성 계수의 경우와 마찬가지로 구속압에 관계없이 간극비에 따라 대략 $17{\sim}18%$에서 발생하였으며, 이 또한 최적포화도에서 표면장력의 영향으로 감쇠비가 가장 작게 나타나는 것으로 판단된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제11권2호
• /
• pp.125-133
• /
• 2007

CFS로 둘러싸서 외부에서 구속하는 방법은 정적 혹은 지진하중을 받는 철근콘크리트 기둥을 보강하는데 매우 효과적이다. 이러한 CFS 보강법의 신뢰성 있고 경제적인 설계를 위해서는 정확한 CFS 구속콘크리트의 응력-변형률 관계를 파악하는 것이 필요하게 된다. 본 연구에서는 원형단면을 갖는 단주 RC 기둥에 대해서 일축압축 실험을 실시하였다. CFS 면적비, 나선철근 면적비, 그리고 콘크리트 압축강도가 CFS로 구속된 콘크리트의 응력-변형률관계에 대한 영향을 평가하기 위한 실험변수로서 고려되었다. 기둥을 CFS로 횡보강함으로서 콘크리트의 강도 및 연성이 크게 증가되었다. 또한, 나선철근이 배근된 실험체의 강도증가율은 CFS만으로 횡보강된 실험체보다 횡보강성능이 크고 작게 나타났다.

• 대한토목학회논문집
• /
• 제26권4A호
• /
• pp.565-575
• /
• 2006

구속된 콘크리트는 구속되지 않은 콘크리트에 비해 상당히 큰 강도를 갖는다. 따라서 콘크리트의 구속응력을 증가시키는 것은 강도의 증가를 유도할 수 있다. 하지만 중공교각의 경우, 심부구속력의 부재로 인하여 중공교각의 안쪽면에서 취성파괴가 발생하며, 이는 기둥의 강도 저하 및 연성의 저하를 초래한다. 이러한 문제를 극복하기 위하여, 강관 삽입 중공 RC(Reinforced Concrete) 기둥이 개발되었으며, 본 연구에서는 실험을 통하여 삽입 강관에 의한 내부 구속력의 효과를 검증하였다. 총 36개의 시험체를 제작하여 실험을 수행하였으며, 실험 결과를 통하여 삽입 강관의 구속력과 이로 인한 콘크리트의 강도 증가를 확인하였다.

• Advances in concrete construction
• /
• 제9권6호
• /
• pp.597-610
• /
• 2020

Stress-strain models of fibre reinforced polymer (FRP) confined concrete have been widely investigated; however, the existing load which is always supported by structures during the retrofitting phase, namely 'preload', has been neglected. Thus, preload effects should be clarified, providing insightful information for FRP retrofitting of structures with preload conditions. Towards this aim, experiments were performed for 27 cylinder concrete specimens with the diameter 150 mm and the height 300 mm. Three specimens were used to test the compressive strength of concrete to compute the preloads 20%, 30% and 40% of the average strength of these specimens. Other 24 specimens were divided into 2 groups; each group included 4 subgroups. Four subgroups were subjected to the above preloads and no preload, and were then wrapped by 2 FRP layers. Similar designation is applied to group 2, but wrapped by 3 FRP layers. All specimens were tested under axial compression to failure. Explosive failure is found to be the characteristic of specimens wrapped by FRP. Experimental results indicated that the preload decreases 12-13% the elastic and second stiffness of concrete specimens wrapped by 2 FRP layers. The stiffness reduction can be mitigated by the increase of FRP layers. Preload negligibly reduces the ultimate force and unclearly affects the ultimate displacement probably due to complicated cracks developed in concrete. A mechanism of preload effects is presented in the paper. Finally, to take into account preload effects, a modification of the widely used model of un-preload FRP confined concrete is proposed and the modified model demonstrated with a reasonable accuracy.

• Earthquakes and Structures
• /
• 제7권5호
• /
• pp.843-859
• /
• 2014

In the present study, the seismic performance of structural walls with boundary elements confined by conventional tie hoops and steel fiber concrete (SFC) was investigated. Cyclic lateral loading tests on four wall specimens under constant axial load were performed. The primary test parameters considered were the spacing of boundary element transverse reinforcement and the use of steel fiber concrete. Test results showed that the wall specimen with boundary elements complying with ACI 318-11 21.9.6 failed at a high drift ratio of 4.5% due to concrete crushing and re-bar buckling. For the specimens where SFC was selectively used in the plastic hinge region, the spalling and crushing of concrete were substantially alleviated. However, sliding shear failure occurred at the interface of SFC and plain concrete at a moderate drift ratio of 3.0% as tensile plastic strains of longitudinal bars were accumulated during cyclic loading. The behaviors of wall specimens were examined through nonlinear section analysis adopting the stress-strain relationships of confined concrete and SFC.

• 한국농공학회지
• /
• 제31권2호
• /
• pp.66-81
• /
• 1989

The characteristics of resilient modulus(Mr) which dominates the life of pavement and the design of pavement were investigated on the test specimens which were cement treated and non-treated of the three different soil types. The results are summarized as follows : 1. The resilient modulus was decreased by increasing the cyclic deviator stress ($\sigma$d) , especially the resilient modulus was gradually decreased or sometimes increased when the value of ad was greater than 0.75- 1. 0kg/cm$^2$. 2. The resilient modulus was increased by increasing the homogeneous confined stress ($\sigma$do) and such phenomena were distinct on the coarse soils. 3. The resilient modulus was increased by increasing the ratio of confined stress(Kc), and this phenomena were eminent on the coarse soils too, and the higher permanent strain was showed by increasing the value of Kc. 4. In the drained cyclic triaxial compression test, the value of ad, Kc, and (Oho) was introduced by the following interrelated equations which were similar to the Mr model of Cole. Kcn/Mr=K1(J$_2$/ $\tau$oct)K2 ............. (coarse soli) Mcn/Mr=K3($\sigma$dp/ $\tau$f)k4 ...............(fine soils) 5. The stress path was not much affected by the value of Mr, however, moisture content, dry desity, and contant of fines affected the value of Mr. 6. In the soil-cement specimens, the resilient compression strain($\varepsilon$d) was decreased by the increment of the $\sigma$ho, and Mr was decreased by increasing the $\sigma$d 7. In the flexible pavement. the cement treated layer should be designed not to fail by the fatigue before the designed traffic load, and actually the pavement could cover the traffic load to a certain extent under the post-crack phase, therefore farther studies on this phenomena' are required in the design analysis. 8. The finite element computer program (ANALYS) was used for displacement analysis of pavement containing the cement-treated layer, The result showed that the program used for this analysis was proved to be usable.

• 한국구조물진단유지관리공학회 논문집
• /
• 제4권4호
• /
• pp.171-180
• /
• 2000

This study aims to present a more reasonable control value than the exiting one by comparing and analyzing control values and field instrumentation values of the whole excavation depth of the four case sites using geometric averaging as a statistical method. The range of the study is confined to three things: (1) the axial force of the braced excavation walls among a variety of items prescribed in the control values by stress deformation of walls and adjacent structures; (2) by approximation of the allowable and design value; (3) and by safety factor. As a res it is desirable to revise "(Long term allowable stress + Short term allowable stress)/2 ~ Short term allowable stress," presented in the present control values by stress deformation of walls and adjacent structures, to "(Long term allowable stress + Short term allowable stress)/5 ~ (Short term allowable stress)/3." The result also shows that since there is a difference of about 3.5%, it is not necessary to revise 70, 90, and 100 percent of LEVEL I, II, and III, prescribed in the control values by the allowable and design value approximation. In addition, modifying the control value by the safety factor, now 1.07, is unnecessary, although it varies little difference from the present value.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.1172-1177
• /
• 2010

For the deep excavation in urban area, the braced-cut method is mainly adopted. In this case, inadequate consideration of ground water level may result in wrong prediction of structural behavior. In this study, the effects of hydraulic interaction between wall and grout were investigated using the finite element method. The maximum stress in case of confined ground water condition is obtained at the final excavation stage in the range of 70~80% of excavation depth. The stress of impermeable case is about 50% larger than that of permeable case. When the relative permeabililty of wall-grout become smaller, the stress is getting bigger. And the stress tends to converge in case of 1/100 or less of the relative permeability.

• KCI Concrete Journal
• /
• 제13권1호
• /
• pp.53-60
• /
• 2001

Tests of cylindrical concrete specimens under lateral confining pressure of up to 5,000 psi were conducted for two different axial loading cases: monotonic compression and monotonic tension. The purpose of this experimental investigation is to provide stress-strain characteristics of plain concrete in triaxial stress conditions. Lateral confining pressure levels, loading rates, and strength of concrete specimens are varied as parameters. The loading rates are $34.75$\times$10^{-5}$ in/in/sec for fast, $\times$$6.95x10^{-5}$ in/in/sec for normal. and $0.579$\times$10^{-5}$ in/in/sec for slow loading cases. The concrete specimens used in the experiment have compressive strength of 3,500 psi and 6,500 psi, respectively. Findings of this experiment include dependency of the stress-strain behavior of concrete on the above parameters under two different types of loading conditions. The parametric study includes a series of 106 triaxial tests.