• 반도체디스플레이기술학회지
• /
• 제17권4호
• /
• pp.51-55
• /
• 2018

As the OLED industry develops, display equipment is becoming larger. As a result, the stage required for display equipment is getting bigger. This enlargement led to increase in OLED production and industrial development. However, due to the large scale of the stage, other problems due to overheating and overheating caused by heavy load on the linear motor, which is mainly used in the stage, must be solved. In this study, a linear motor equipped with a cooling channel is modeled and the three - dimensional heat conduction flow analysis for this model is simulated using Fluent to analyze the cooling efficiency and cooling efficiency according to the cooling water flow rate. As a result, the cooling channel was effective and the cooling effect and efficiency were the best when the flow rate was about 5 ~ 10 L./min. In addition, the cooling effect is increased when the flow rate is increased, but the efficiency is significantly lowered when the flow rate is more than the predetermined value.

• 한국초전도ㆍ저온공학회논문지
• /
• 제21권3호
• /
• pp.47-50
• /
• 2019

The paper gives the results of the experiments with a model two-section REBCO solenoid cooled by either gaseous helium (GHe) or sub-cooled/solid nitrogen (SN2) in (50-77) K temperature range. The major cooling source was a single-stage cryocooler Sumitomo CH-110 with the cooling power of 175 W and 130 W at 77 K and 50 K respectively. The coil itself was not directly conduction cooled. We compare the time taken by both coolants to obtain the temperature of the magnet of about 50 K and the homogeneity of the temperature distribution within the cryostat. Test results for the coil operation in solid nitrogen together with the comparison of its critical properties in SN2 and GHe are also presented.

• 한국산업융합학회 논문집
• /
• 제24권4_1호
• /
• pp.411-419
• /
• 2021

In this study, IGBT_Total_Loss and DIODE_Total_Loss were used to analyze the slope of the junction temperature for each section for temperature and duty variables in order to simply calculate the junction temperature of the power semiconductor (IGBT). As a result of the calculation, IGBT_Max_Junction_Temp and DIODE_Max_Junction_Temp form a proportional relationship with temperature for each duty. This simulation data shows that the power loss of a power semiconductor is calculated in a complex manner according to the current dependence index, voltage dependence index, and temperature coefficient. By applying the slope for each condition and section, the junction temperature of the power semiconductor can be calculated simply.

• Steel and Composite Structures
• /
• 제51권4호
• /
• pp.377-389
• /
• 2024

In the present study, thermoelsatoplastic stresses and displacement for rotating hollow disks made of functionally graded materials (FGMs) has been investigated. The linear elastic-fully plastic condition is considered. The material properties except Poisson's ratio are assumed to vary in the radial direction as a power-law function. The heat conduction equation for the one-dimensional problem in cylindrical coordinates is used to obtain temperature distribution in the disk. The plastic model is based on the Tresca yield criterion and its associated flow rules under the assumption of perfectly plastic material behavior. Exact solutions of field equations for elastic and plastic deformations are obtained. It is shown that the elastoplastic response of the functionally graded (FG) disk is affected notably by the radial variation of material properties. It is also shown that, depending on material properties and disk dimensions, different modes of plastic deformation may occur.

• 설비공학논문집
• /
• 제18권8호
• /
• pp.678-685
• /
• 2006

Analysis of drying characteristics has been carried out with one-dimensional model in the dryer using the principle of the refraction of radiation. The dryer is composed of hot water tank, plastic film conveyer belt, drying material, etc. The model considers the con-duction and radiation within the plastic film and drying material. The film is semitransparent to radiation and the drying material is assumed to be semitransparent or opaque to radiation. The results show that the effect of radiative transfer on the drying rate is relatively large when the thickness of drying material is small and the water temperature is high. When the material is thin, the drying rate due to conduction is also enhanced and the drying time can considerably be reduced.

• 항공우주기술
• /
• 제6권1호
• /
• pp.173-181
• /
• 2007

단위 장비 수준에서 시스템 수준에 이르기까지 통제되는 KSLV-I 2단부의 복사성 방사/감응 특성은 탑재되는 위성, 발사체 1단부, 그리고 우주센터에 설치되고 운용되는 지상장비 및 외부 통신망의 정상동작을 보장하기 위하여 전 주파수 대역에 대해 시험 및 관리되어야 한다. KSLV-I과 하부시스템에서 방사되는 비의도성 잡음은 각각의 요구규격에 정의된 제한치 보다 작도록 제한되어야 할 뿐만 아니라 시스템의 특성을 정확히 검증하기 위한 적절한 시험 및 평가 방법도 개발되어야 한다. 본 논문에서는 KSLV-I 2단부 엔지니어링 모델의 전자파적합성 확보를 위해 도출된 복사성 방사와 복사성 감응에 대한 시험규격, 측정방법 그리고 시험 결과가 제시된다.

• 대한기계학회논문집B
• /
• 제23권8호
• /
• pp.945-956
• /
• 1999

This work reports a set of approximate analytical solutions describing the initial transient process of close-contact melting between a rectangular parallelepiped solid and a flat plate on which either constant temperature or constant heat flux is imposed. Not only relative motion of the solid block tangential to the heating plate, but also the density difference between the solid and liquid phase is incorporated in the model. The thin film approximation reduces the force balance between the solid weight and liquid pressure, and the energy balance at the melting front into a simultaneous ordinary differential equation system. The normalized model equations admit compactly expressed analytical solutions which include the already approved two-dimensional solutions as a subset. In particular, the normalized liquid film thickness is independent of all pertinent parameters, thereby facilitating to define the transition period of close-contact melting. A unique behavior of the solid descending velocity due to the density difference is also resolved by the present solution. A new geometric function which alone represents the three-dimensional effect is introduced, and its properties are clarified. One of the representative results is that heat transfer is at least enhanced at the expense of the increase in friction as the cross-sectional shape deviates from the square under the same contact area.

• 전기학회논문지P
• /
• 제66권4호
• /
• pp.213-218
• /
• 2017

The DC electrolytic capacitor for DC-link of power converter is widely used in various power electronic circuits and system application. Its functions include, DC Bus voltage stabilization, conduction of ripple current due to switching events, voltage smoothing, etc. Unfortunately, DC electrolytic capacitors are some of the weakest components in power electronics converters. Many papers have proposed different algorithms or diagnosis method to determinate the ESR and tan ${\delta}$ capacitance C for fault alarm system of the electrolytic capacitor. However, both ESR vary with frequency and temperature. Accurate knowledge of both parameters at the capacitors operating conditions is essential to achieve the best reference data of fault alarm. According to parameter analysis, the capacitance increases with temperature and the initial ESR decreases. Higher frequencies make the reference ESR with the initial ESRo value to decrease. Analysis results show that the proposed DC Bus electrolytic capacitor reference ESR model setting technique can be applied to advanced reference signal of capacitor diagnosis systems successfully.

• 대한한의진단학회지
• /
• 제9권1호
• /
• pp.131-135
• /
• 2005

Background and purpose: The measurement of direct current (DC) potential on skin area of meridian has recently been adopted to explore the electrophysiological characteristics of meridian system, But there exists two problems to be explained; the entity of the DC potential to be measured and the characteristics of electrode gel interface of measurement system, It is not clear whether the DC potential reflect, at least hypothetically, the entity of meridian, and if there exist any unstable factor in the DC potential measurement system. Methods: In this study, we designed an electronic circuit model of skin and applied known DC potential sources $({\pm}10.75mV,\;0mV)$ to the electrode interface of the skin model. Results: The result showed that the measured DC potential changed according to the time, and the same phenomenon was observed when the electrode gel was replaced with an electric condenser. It is suggested that the measurement of DC potential on electrode gel interface is very difficult and produces unstable values due to the capacity effect of electrode gel. Conclusion: Further studies on the DC potential evaluation in the context of meridian study should consider and bypass this problem.

• 한국안광학회지
• /
• 제4권2호
• /
• pp.105-111
• /
• 1999

PECVD 방법에 의하여 제작된 수소화된 비정질 탄소박막에서 측정 전압에 따른 전기전도도의 급격한 변화와 시간에 따른 전류의 이완 현상을 관측하였다. 이 현상은 Hammer 등에 의해 four-probe 측정과 샌드위치형 전극 시료에 대해서 측정한 것과 동일하였다. 본 연구에서는 "높은 전압에서 전자가 트랩에 포획될 확률이 작아진다"는 가정 하에서 정성적이지만 전기전도도의 측정 전압 의존에 관한 세 가지 현상이 비교적 잘 설명됨을 제시하였다.