• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.350-353
• /
• 1999

This Paper Presents the optimized design of micro-heaters using 501(Si-on-insulator) substrate and oxide-filled trench structure In order to justify a lumped model approximation and thermal boundary assumptions, two-dimensional FDM(finite difference among which conduction is the dominant heat dissipation path. Compared with no-trenchs on the SOI structure, the micro-heaters with trench structures has properties of low heater loss and good thermal isolation. The simulation results show that the heater loss decreases as the number. width and distance of trenchs increases.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• 제5권4호
• /
• pp.354-358
• /
• 2004

In this thesis, an analytical model for Ⅰ-Ⅴ characteristics of an n-AlGaAs/GaAs Delta doped HEMT is proposed. 2-dimensional electron gas density, and conduction band edge profile are calculated from a self-consistent iterative solution of the Poisson equation. Parameters, e.g., the saturation velocity, 2-dimensional electron gas concentration, thickness of the doped and undoped layer(AlGaAs, GaAs, spacer etc.,) are in good agreement with the independent calculations.

• Journal of Power Electronics
• /
• 제15권1호
• /
• pp.39-53
• /
• 2015

This paper presents the regulation of the output voltage and inductor currents in a Single Ended Primary Inductor Converter (SEPIC), operating in the continuous conduction mode (CCM) using a sliding mode controller. Owing to the time varying nature of the SEPIC converter, designing a feedback controller is a challenging task. In order to improve the dynamic performance of the SEPIC, a Sliding Mode Controller (SMC) is developed. The developed SMC is designed by using a state space average model. The performance of the developed controller with the SEPIC converter is validated at different working conditions through Matlab simulations. It is also compared with the performance while using a PI controller. The results show that the designed controller gives very good output voltage regulation under different operating conditions such as a varying input voltage, changes in the load and component variations. A 48V, 46W experimental setup for has been developed in an analog platform to validate the performance of the proposed SMC.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.157-159
• /
• 1996

The secondary arcing phenomenon can be hardly modeled for computer simulation due to its particularly nonlinear characteristics. This paper describes a new computer modeling technique for the secondary arc which can be implemented with the EMTDC. The computer model proposed is based on realistic are conduction behaviors through both FIT and variable resistor modules which is supported in the EMTDC. Simulation results using the proposed technique are compared with some previous studies.

• Proceedings of the KAIS Fall Conference
• /
• 한국산학기술학회 2004년도 춘계학술대회
• /
• pp.158-161
• /
• 2004

In this study, an analytical model for I-V characteristics of an n-AIGaAs / GaAs Delta doped HEMT is proposed. The two-dimensional electron gas density and the conduction band edge profile are calculated from a self-consistent iterative solution of the Poisson equation. The parameters, which include the saturation velocity, two-dimensional electron gas concentration, thickness of the doped and undoped layer(AIGaAs, GaAs, spacer etc.,), are in good agreement with the independent calculations.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.1159-1161
• /
• 1993

This paper may be presented the carrier oscillation properties for the varistor fabricated by a new method of three-composition seed grain, in order to analyze the behavior of carriers at the its equivalent circuit model. The oscillation phenomena of carriers appeared from current-voltage characteristics under knee voltage is shown by the transient flow of non trapped carriers group in the trap level of intergranular layer, surface state and/or depletion layer. However, Current oscillation phenomena is hardly shown in the high electric field. The injected carriers from both electrodes are directly flowed from the conduction band of forward biased grain through the intergranular layer into the reverse biased grain, because the trap level in the electric field above the knee voltage is mostly filled.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.142-143
• /
• 2006

Organic thin film transistors(OTFTs) were simulated by a SPICE model adopted in the amorphous TFTs(a-Si:H TFTs). The gate voltage-dependent mobilities were assumed to fit the representative current-voltage characteristics. The optimal fitting procedures were suggested to compare the experimental data with the mathematical expressions used in the amorphous TFTs. Each SPICE parameter explains the gate dependent mobilities in OTFTs which might originate from the influence of the hopping conduction.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제29권4호
• /
• pp.526-536
• /
• 2005

A heat dissipation modeling method of EEE parts, or semi-empirical heat dissipation method, is developed for thermal design and analysis an electronic equipment of geostationary satellite. The power consumption measurement value of each functional breadboard is used for the heat dissipation modeling method. For the purpose of conduction heat transfer modeling of EEE parts, surface heat model using very thin ignorable thermal plates is developed instead of conventional lumped capacity nodes. The thermal plates are projected to the printed circuit board and can be modeled and modified easily by numerically preprocessing programs according to design changes. These modeling methods are applied to the thermal design and analysis of CTU (Command and Telemetry Unit) and verified by thermal cycling and vacuum tests.

• Journal of the Korean Society of Industry Convergence
• /
• 제5권4호
• /
• pp.303-307
• /
• 2002

We consider the problem y"=a(x,y)(y-b), (0$$y(0)=0,\;y^{\prime}(1)=g(y({\xi}),\;y^{\prime}({\xi})),\;{\xi}$$ fixed in (0,1). This is a model of steady-state heat conduction in a rod when the heat flux at the end x=1 is determined by observation of the temperature and heat flux at some interior point ${\xi}$. We establish conditions sufficient for existence, uniqueness, and positivity of solutions.

• Journal of the Semiconductor & Display Technology
• /
• 제17권4호
• /
• pp.51-55
• /
• 2018

As the OLED industry develops, display equipment is becoming larger. As a result, the stage required for display equipment is getting bigger. This enlargement led to increase in OLED production and industrial development. However, due to the large scale of the stage, other problems due to overheating and overheating caused by heavy load on the linear motor, which is mainly used in the stage, must be solved. In this study, a linear motor equipped with a cooling channel is modeled and the three - dimensional heat conduction flow analysis for this model is simulated using Fluent to analyze the cooling efficiency and cooling efficiency according to the cooling water flow rate. As a result, the cooling channel was effective and the cooling effect and efficiency were the best when the flow rate was about 5 ~ 10 L./min. In addition, the cooling effect is increased when the flow rate is increased, but the efficiency is significantly lowered when the flow rate is more than the predetermined value.