• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제44회 KOSCO SYMPOSIUM 초록집
• /
• pp.105-106
• /
• 2012

This study is numerical analysis about optimal conditions of GDICI (gasoline direct injection compression ignition) engine operation using intake preheating. Numerical modeling was performed by using the KIVA-3V Release2 code integrated Chemkin chemistry solver II. For validation of numerical model, experiments were performed on a single-cylinder engine. Throughout the numerical simulations under variable conditions, the ranges of optimal conditions were found.

• Structural Monitoring and Maintenance
• /
• 제9권1호
• /
• pp.59-80
• /
• 2022

In the present study, the objective is to detect the structural damages using the responses obtained from the sensors at the optimal location under uncertainty conditions. Reducing the error rate in damage detection process due to responses' noise is an important goal in this study. In the proposed algorithm for optimal sensor placement, the noise of responses recorded from the sensors is initially reduced using the principal component analysis. Afterward, the optimal sensor placement is obtained by the damage detection equation based sensitivity analysis. The sensors are placed on degrees of freedom corresponding to the minimum error rate in structural damage detection through this procedure. The efficiency of the proposed method is studied on a truss bridge, a space dome, a double-layer grid as well as a three-story experimental frame structure and the results are compared. Moreover, the performance of the suggested method is compared with three other algorithms of Average Driving Point Residue (ADPR), Effective Independence (EI) method, and a mass weighting version of EI. In the examples, young's modulus, density, and cross-sectional areas of the elements are considered as uncertainty parameters. Ultimately, the results have demonstrated that the presented algorithm under uncertainty conditions represents a high accuracy to obtain the optimal sensor placement in the structures.

• 한국응용과학기술학회지
• /
• 제28권1호
• /
• pp.6-9
• /
• 2011

Step feed process was analyzed stoichiometrically for the optimal operation conditions in this study. In case of optimal operation conditions, minimum R (sludge recycling) value, r (internal recycling ratio) value, and n (influent allocation ratio) value for the step feed process to acquire the maximum TN removal efficiency were identified by theoretical analysis. Maximum TN removal efficiency, based on stoichiometric reaction, can be obtained by controlling n value for the step feed process.

• 지역연구
• /
• 제10권2호
• /
• pp.45-51
• /
• 1994

The purpose of this paper is to present the optimal investment conditions of SOC facilities for maximizing regional social welfare in implementing the urban development project in the theoretical fashion. Particularily, SOC facilities are divided into both supply-side($P_s$) and demand-side SOC ($P_d$) in the paper. General equilibrium analysis from the intra-regional viewpoint by utilizing Pareto's Optimal Conditions and by revising Samuleson's Conditions for public goods($P_s$ and $P_d$) results in the optimum pattern of SOC investment. The following are important implications from the analysis. First, rather than the pursue social equity, SOC investment is to resolve the issue of efficiency to activate the regional economy. Second, the marginal rate of transformation (MRT) between $P_s$ and $P_d$ in the region is to play a significant role in structuring SOC investment plant of local government for social welfare maximization. Third, the optimal SOC investment policy based on this regional economy but also to generate the enhancement of soical amenities of the residents.

• 한국정밀공학회지
• /
• 제15권6호
• /
• pp.79-89
• /
• 1998

In determining optimal cutting condition for face milling operation, tool wear is an important factor. For the purpose of establishing the relationship between various machining factors and tool wear, cutting tests have been performed. As a result, hardness and chemical composition of workpiece material, chemical composition and grain size of cutting tool and cutting speed have been selected as machining factors. In addition, relationship between feed rate and workpiece hardness has been observed. Prior to utilizing cutting conditions recommended by ‘Machining Data Handbook(MDH)’ as a knowledge base, an analysis for the validity of the MDH has been provided. Based on this analysis, tool life criteria applied by MDH has been modified. Finally, using MDH recommended data for neural network trainning, the results from the trained neural network for optimal cutting condition for some given workpiece and cutting tool can be used as reference cutting conditions.

• 분석과학
• /
• 제17권2호
• /
• pp.192-197
• /
• 2004

The discrimination of bracken (Korean vs. Chinese) has been attempted using capillary electrophoresis (CE). Bracken (Pteridium aquilinum) was extracted with 30% methanol and separated on a uncoated fused-silica ($50{\mu}m{\times}27cm$) capillary. Conditions for optimal analysis include: temperature, $40^{\circ}C$; voltage, 8 kV; and pressure injection time, 5 sec. The optimal separation buffer was 0.3 M borate buffer (pH 8.5) containing 40 mM CHAPS with 30% ethylene glycol. Under the optimal conditions established for CE, the ratio of specific peak area (peak PA-1) to other peak area (peak PA-2) was effective in discrimination of Korean and Chinese bracken. The mean accuracy for discrimination of Korean and Chinese brackens were 80% and 86%, respectively.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.2060-2060
• /
• 2011

This paper was investigated the frequency property for optimal operating conditions of mono-crystalline Si solar cell. An internal impedance of mono-crystalline Si solar cell was influenced frequency. An optimal operating conditions of solar cell was under about 10[kHz].

• Journal of Construction Engineering and Project Management
• /
• 제4권4호
• /
• pp.33-40
• /
• 2014

Maximizing the profitability and minimizing the duration of construction projects in extreme weather regions is a challenging objective that is essential for project success. An optimization model is presented herein for the time-profit trade-off analysis of construction projects under extreme weather conditions. The model generates optimal/near optimal schedules that maximize profit and minimize the duration of construction projects in extreme weather regions. The computations in the model are organized into: (1) a scheduling module that develops practical schedules for construction projects, (2) a profit module that computes project costs (direct, indirect, and total) and project profit, and (3) a multi-objective module that determines optimal/near optimal trade-offs between project duration and profit. One example is used to show the impact of extreme weather on construction time and profit. Another example is used to show the model's ability to generate optimal trade-offs between the time and profit of construction projects under extreme weather conditions.

• Journal of applied mathematics & informatics
• /
• 제23권1_2호
• /
• pp.243-256
• /
• 2007

This paper deals with determining the sufficient conditions of minimum for the class of problems in which the necessary conditions of optimum are satisfied in the strengthened form Legendre-Clebsch. To this paper, we shall use the sweep method which analysis the conditions of existence of the conjugated points on the optimal trajectory. The study we have done evaluates the command variation on the neighboring optimal trajectory. The sufficient conditions of minimum are obtained by imposing the positivity of the second variation. The results that this method offers are applied to the problem o the orbital rendez-vous for the linear case of the equations of movement.

• 산업공학
• /
• 제9권1호
• /
• pp.13-24
• /
• 1996

Quality of injection molded parts is dependent on both mold design and processing conditions. From the mold design point of view, an optimal shrinkage should be used to compensate the shrinkage of molded parts. From the processing point of view, it is important to analyze the priority of processing conditions because a number processing conditions affect the quality of molded parts. Processing analysis employing the design of experiment was performed, and the shrinkage of molded part was considered as a characteristic parameter to improve the quality. As the result of the analysis of variance on SN ratio of a characteristic value, injection speed and bolding pressure were selected as two effective process parameters. Regression analysis on shrinkage and processing conditions was carried out, and an optimal processing condition was obtained by the response surface analysis. Shrinkage at the optimal condition could be used to reduce the number of try-cut at the step of mold making. The ranges of indirect control parameter, such as maximum cavity pressure or weight, measured at the optimal processing condition were used for monitoring the quality of molded parts in process.