• Journal of Korean Ophthalmic Optics Society
• /
• v.4 no.2
• /
• pp.45-49
• /
• 1999

The second harmonic, wavelength is 397nm, of the continuous wave diode laser, whose maximum power is 35mW, was generated in $LiIO_3$ crystals in a ring enhancement cavity. 5mm- and 10mm-long crystals cut $43.21^{\circ}$ for optic axis were used in this experiment. Both surfaces of those were anti-reflection coated for 794nm. In case the crystal was inserted into the cavity, the condition of separation between two concave mirrors for the optimum mode matching was found. The conversion efficiency of second harmonic generation was increased by the resonant enhancement of pumping power in the ring enhancement cavity, and the frequency of diode laser was locked to that of the counter-propagation mode generated from the surface of crystal. When the pumping power was 28 mW, the infrared buildup factor was about 45 without the crystal, and 14 with the crystal due to the transmission loss of crystal. The maximum second harmonic powers of $1.5{\mu}W$ and $6.6{\mu}W$ were obtained, and corresponding conversion efficiencies were $(6.584{\pm}0.56){\times}10^{-3}$%, $2.6{\pm}0.21){\times}10%{-2}$% in 5mm- and 10mm-long $LiIO_3$, respectively.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.4 no.3
• /
• pp.175-184
• /
• 2002

Ground reaction curve is very useful information for estimating the installation time of the tunnel support. The ground reaction curve can be estimated by analytical closed form solutions derived in case of circular section and isotropic stress condition. The nature of the ground reaction, however, depends significantly on tunnel configurations. Nevertheless, few purely analytical and experimental studies of this problem due to tunnel configurations appear to have been carried out. Therefore, it is necessary to investigate the influence of tunnel configurations in order to use simply in practical design. This paper describes a numerical study for the intial elastic displacement in the ground reaction curve due to configuration of tunnel excavation. In order to evaluate the applicability of analytical closed form solution in practical design, the parametric studies were carried out by numerical analysis in elastic tunnel behaviour. In the studies, S value, namely configuration factor, defined as the ratio between tunnel height (b) and width (a), varies between 0.5 and 3.0, initial ground vertical stress varies between 5~30 MPa for each S values. The results indicated that the self-supportability of ground is larger in the ground having low S value. It, however, is suggested that the applicability of closed form solution may not be adequate to determine directly the installation time of the support and self-supportability of ground. It should be necessary to perform the additional numerical analysis.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.9
• /
• pp.1319-1327
• /
• 2014

Two feeding trials were conducted to determine the optimum feeding frequency in growing Korean rockfish, (Sebastes schlegeli) reared at the temperatures of $15^{\circ}C$ and $19^{\circ}C$. Fish averaging $92.2{\pm}0.7$ g (mean${\pm}$standard deviation [SD]) at $15.0{\pm}0.5^{\circ}C$ and $100.2{\pm}0.4g$ ($mean{\pm}SD$) at $19.0{\pm}0.5^{\circ}C$ water temperature were randomly distributed into each of 15 indoor tanks containing 250-L sea water from a semi-recirculation system. A total of five feeding frequency groups were set up in three replicates as follows: one meal in a day at 08:00 hour, two meals a day at 08:00 and 17:00 hours, three meals a day at 08:00, 14:00, and 20:00 hours, four meals a day at 08:00, 12:00, 16:00, and 20:00 hours, and one meal every 2 days at 08:00 hour. Fish were fed at the rate of 1.2% body weight (BW)/d at $15^{\circ}C$ and 1.5% BW/d at $19^{\circ}C$. At the end of 8 wks of feeding trial weight gain and specific growth rate were significantly higher at the fish fed groups of one meal a day and two meals a day at $15^{\circ}C$ and fish fed groups of 1 meal every 2 days at $19^{\circ}C$ were significantly lower than those of all other fish fed groups. Glutamic oxaloacetic transaminase and glutamic pyruvic transaminase of fish fed group at 1 meal every 2 days was significantly higher than those of all other fish fed groups in both experiments. Weight gain, specific growth rate and condition factor were gradually decreased as the feeding frequency increased. The results indicate that growing Korean rockfish 92 and 100 g perform better at $15^{\circ}C$ than $19^{\circ}C$ water temperature. As we expected, current results have indicated that a feeding frequency of 1 meal a day is optimal for the improvement of weight gain in growing Korean rockfish grown from 92 g to 133 g at $15^{\circ}C$ and 100 g to 132 g at $19^{\circ}C$ water temperature.

• Journal of the Korean association of regional geographers
• /
• v.13 no.5
• /
• pp.526-542
• /
• 2007

This study look into the place-name change by social influence around Jin-An region. The place-names were made through joining natural environment with social condition. The place-names were born as a river name firstly, and it was selected as the artificial administration district name in this region(Ju-Chon, Jeong-Chon, An-Chon). Generally the place-name is reflected by a terrain feature of narrow area but this region's place name was made by wide river drainage area as a system. It is different point to others place-name and the social factor played more important role than natural environment in this process. The displacement process of mountain name which is from Ju-Jul to Un-Jang was through social situation change without the natural conditions change. It was used to the Ju-Jul firstly and coexistent the Ju-Jul with Un-Jang and only use the Un-Jang recently. Formal change period was 1910s in the map, Mt. Un-Jang(雲長山) had the advantage at the pronunciation and written than Mt. Ju-Jul. Mt. Gu-Bong(九峰山) was played important role for new mountain name and Song Ik-Pil(宋翼弼) was appeared for rationalization of Mt. Un-Jang.

• Applied Biological Chemistry
• /
• v.39 no.1
• /
• pp.1-8
• /
• 1996

A one-stage, continuous-flow bioreactor with both immobilized and suspended cells was used to investigate the roles of lipid supplements in ethanol production by Saccharomyces cerevisiae. The reactor performance and the level of alcohol dehydrogenase(ADH) activities of the suspended cells, grown under various conditions, were measured. When ergosterol and/or oleic acid were added with surfactants to the yeast culture grown under non-aerated conditions, remarkable increases in ethanol production and cell growth was achieved, but specific ADH activities were not affected. Especially, no difference of specific ADH activities of the suspended cells grown under aerated and non-aerated condition was observed. The addition of the surfactant as a supplement also resulted in significant increases in ethanol production, cell growth, and specific ADH activity. When ergosterol and oleic acid were added to the yeast culture exposed to higher ethanol concentration($>40\;g/{\ell}$) level, ethanol production, cell growth, and specific ADH activity were increased, but the addition of surfactant was as effective as at lower ethanol concentration level. The results indicated that lipid supplements were more effective at higher ethanol concentration level than at lower ethanol concentration level during ethanol production. ADH isozyme patterns of the yeast cultures grown under various conditions on starch gel electrophoresis showed only one major band, probably ADH I. The migrating distance of the major isozyme, however, varied slightly according to the culture conditions of the cells. No apparent correlation was found between specific ADH activity and amount of ethanol produced. Cell mass was more important factor for ethanol production than specific ADH activity of the cells.

• Journal of Yeungnam Medical Science
• /
• v.20 no.2
• /
• pp.105-116
• /
• 2003

Definitely, treatment for gastric cancer is primarily surgical. Detection in early stage of disease and complete surgical resection is the best way to cure gastric cancer. If surgery is planned, careful preoperative evaluation and corrections of physiologic and psychologic abnormalities are essential to reduce perioperative morbidity or mortality. Basic principle of gastrectomy for gastric cancer is an en bloc resection of tumor with adequate margins of normal tissue and with regional lymph nodes and omental tissues. To complete these principles, regional lymph nodes and all omental tissues should be removed altogether during performing various types of gastric resection. The lymph node dissection is one of the most effective procedures for gastric cancer to achieve curative resection. The basic types of gastric resection are distal subtotal gastrectomy and total gastrectomy according to the condition of primary lesions and the status of lymph node metastases. When the primary lesion is located near the esophagogastric junction, it is sometimes hard for a surgeon to select adequate surgical method. Postoperative quality of life in a patient has become a very important factor to be considered in every step of surgical therapy. With increasing incidence of early gastric cancer, a number of surgical trials for limited surgery or endoscopic procedures have been performed, but the long-term clinical results should be carefully analyzed to define the clinical relevance of these new techniques. For patients with disseminated gastric cancer, a palliative procedure can be performed to improve quality of life of patients and to avoid immediate death due to the cancer-related complications.

• The Journal of Engineering Geology
• /
• v.26 no.3
• /
• pp.413-422
• /
• 2016

With the rapidly increasing population density and development of infrastructure, the loss of life and property damage caused by landslides has increased gradually in urban area. Especially, Because Busan has high percentage of mountainous terrain among the metropolitan in Korea, it is unavoidable to develop mountainous region excessively. The objective of this evaluation is to study on landslide hazard possibility for Mt. Hwangryeong in Busan Metropolitan City using the infinite slope model considering the groundwater level. All data related to creating the thematic maps was carried out using ArcGIS 10.0. The results show that FS (Factor of Safety) for landslide is inversely proportional to groundwater level change as expected. Most area indicates stable state in dry condition, and unstable area increase due to high pore water pressure when the groundwater level rise. However, several places in high lineament density area where landslide has been previously occurred, are more stable than other places according to the analysis. This inconsistency between real situation and analysis results indicates that additional analytical method would be necessary to solve the problem. Therefore, we suggest that development of new infiltration theory for unsaturated zone would be helpful to evaluate groundwater level distribution as time goes by.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.4
• /
• pp.39-45
• /
• 1995

The plywoods commonly used as decorative interior materials for the construction are inflammable and so it is a causative factor for making fire accidents, resulting in the destruction of human life and personal properties. Indeed, it is, therefore, required to produce fire-retardant plywoods. In this study, a special grade of defect-free, Kapur plywood was used. Specimens were cut into 3- by 20cm dimensions from 120- by 240- by 0.33-cm panels(thin panel) or 120- by 240- by 0.5-cm panels(thick panel). Some specimens were treated with diammonium phosphate(DAP), but some were not treated with diammonium phosphate to use as control panels. Chemical absorption, drying curves, drying rates and dynamic Young's modulus were investigated. The results were summaries as follows; 1. The specimens were soaked into 19% diammonium phosphate solution by a full cell pressure process and the diammonium phosphate retained in the thin and thick plywoods was 1.409kg/$(30cm)^3$, 1.487kg/$(30cm)^3$, respectively. 2. Diammonium phosphate-treated plywoods were redried with press-drying process at one of either condition dried on the platen($115^{\circ}C$) for a period of time or dried on the platen($50^{\circ}C$) for 3 hrs plus in a dry-oven($30^{\circ}C$) for 24 hrs. or dried on the platen($60^{\circ}C$) for 2 hrs plus in a dry-oven($30^{\circ}C$) for 24 hrs. The drying rate of treated thin specimens dried at $60^{\circ}C$ plus $30^{\circ}C$ and $115^{\circ}C$ only was found to be 0.04 %/min. and 8.53 %/min. Similarly, the drying rate of treated thick specimens were 0.03 %/min. and 6.77 %/min. respectively. 3. It was evident that highly-significantly different drying rate of treated plywoods was observed between plywood thicknesses and platen temperatures and the rate was increased by elevating the platen temperature up to $115^{\circ}C$. Based on the two-way variance analysis, highly significant drying rate was observed from the interaction between plywood thicknesses and platen temperatures. 4. After redrying, the specimens were weighed and reconditioned to a constant weight in a facility maintained temperature ($20^{\circ}C$) and relative humidity(65%) prior to test dynamic Young's modulus. The test revealed that the thin specimens dried at the platen temperature of $50^{\circ}C$, $60^{\circ}C$, $115^{\circ}C$ and untreated specimens showed 1.070E+09 dyne/$cm^2$, 1.156E+09 dyne/$cm^2$, 1.243E+09 dyne/$cm^2$, and 1.052E+09 dyne/$cm^2$, respectively. Likewise, the thick specimens revealed 5.647E+09 dyne/$cm^2$ 5.670E+09 dyne/$cm^2$, 6.395E+09 dyne/$cm^2$ and 5.415E+09 dyne/$cm^2$, respectively. 5. It was evident that significantly different dynamic Young's modulus was observed between the plywood thickness and the platen temperature, but not in the two-way interaction between the plywood thickness${\times}$the platen temperature.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.709-714
• /
• 2018

This study researched the reasons for changing polarity in accordance with junction properties in an interface of semiconductors. The contact properties of semiconductors are related to the effect of the semiconductor's device. Therefore, it is an important factor for understanding the junction characteristics in the semiconductor to increase the efficiency of devices. For generation of various junction properties, carbon-doped silicon oxide (SiOC) was deposited with various argon (Ar) gas flow rates, and the characteristics of the SiOC was varied based on the polarity in accordance with the Ar gas flows. Tin-doped zinc oxide (ZTO) as the conductor was deposited on the SiOC as an insulator to research the conductivity. The properties of the SiOC were determined from the formation of a depletion layer by the ionization reaction with various Ar gas flow rates due to the plasma energy. Schottky contact was good in the condition of the depletion layer, with a high potential barrier between the silicon (Si) wafer and the SiOC. The rate of ionization reactions increased when increasing the Ar gas flow rate, and then the potential barrier of the depletion layer was also increased owing to deficient ions from electron-hole recombination at the junction. The dielectric properties of the depletion layer changed to the properties of an insulator, which is favorable for Schottky contact. When the ZTO was deposited on the SiOC with Schottky contact, the stability of the ZTO was improved by the ionic recombination at the interface between the SiOC and the ZTO. The conductivity of ZTO/SiOC was also increased on SiOC film with ideal Schottky contact, in spite of the decreasing charge carriers. It increases the demand on the Schottky contact to improve the thin semiconductor device, and this study confirmed a high-performance device owing to Schottky contact in a low current system. Finally, the amount of current increased in the device owing to ideal Schottky contact.

• Journal of Korean Society of Forest Science
• /
• v.87 no.3
• /
• pp.459-465
• /
• 1998

To obtain the basic data for the conservation and cultivation of native herb species under the forest, the relations between distribution of native herb species and site factors, distribution of native herb species, and site factors were surveyed on natural forest at subalpine zone in Mt. Odae. Ainsliaea acerifolia, Pseudostellaria palibiniana and Pimpinedla brachycarpa were distributed mainly on broadleaved mixed forest, Clematis fusca var. coreana, Carex siderosticta. Isodon excisus and Vicia unijuga did mainly on gab sites. The distribution of Ligularia fisheri, Aconitum pseudo-laeve var. erectum, Cacalia hastata and Artemisia stolonifera were significantly differed between slope directions. Artemisia stolonifera was distributed more frequently in south directed slope, and Ligularia fisheri, Aconitum pseudo-laeve var. erectum and Cacalia hastata were distributed more frequently in north and west directed slope than the other. The distribution of Aconitum pseudo-laeve var. erectum and Artemisia stolonifera were significantly differed between soil moisture conditions. Artemisia stolonifera was distributed mainly on the dry site, but Aconitum pseudo-laeve var. erectum did mainly on the dry site. Negative correlations between density of Clematis fusca var. coreana, Carex siderosticta. Isodon excises and Vicia unijuga and crown coverage was proved. Aconitum pseudo-laeve var. erectum, Pimpinella brachycarpa, Meehania urticifolia, Smilacina japonica and Pseudostellaria palibiniana were mainly distributed on wet and shady sites under forest canopy, but Pedicularis resupinata, Clematis fusca var. coreana and Artemisia stolonifera did on sunny sites at forest edge or gab.