• International Journal of High-Rise Buildings
• /
• v.5 no.3
• /
• pp.205-211
• /
• 2016

This paper addresses the key technologies for supertall building construction based on the Lotte World Tower project in Korea. First, the mega-mat foundation construction technologies are shown, including ultra-low heat concrete, heat of hydration control programs, and the logistics plan. Then, high strength concrete technologies of 50~80 MPa are introduced and discussed within the context of the highest pumping record in Korea at 514.25 meters. Structural design concepts of gravity load and lateral force resistance systems are introduced, along with surveying systems using GNSS and temporary installation plans of special heavy equipment like tower cranes, hoists, and high pressure concrete pumps. If it is possible to coordinate these key technologies and others, optimizing for the building's design and construction, supertall building construction can be successfully completed.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.3
• /
• pp.95-101
• /
• 2009

Constructing large-scale mat foundation mass concrete is increasing for the stability of building structure, because a lot of high rise building are being built in order to make full use of limited space. However, It is of increasing concerns that because limited placing equipments, available job-site and systems for mass concete placement in construction field do not allow to place great quantity of concrete at the same time in large scale mat foundation, consistency between placement lift can not be secured. And also, it is likely to crack due to stress caused by the difference of hydration heat generation time. To find out the solution against above problems, this study is to reconfirm the performance of normal concrete designed by mix proportion and super retarding concrete. The Fundamental test shows what happens if low heat proportioning and control method of setting time are applied at the job-site of newly constructed high rise building. The test result show that slump flow of concrete has been somewhat increased as the target retarding time gets longer, while the air content has been slightly decreased but this is no great difference from normal concrete. The setting time shows to be retarded as target retarding time gets longer, the range of retarding time increases. It is necessary to increase the amount of mix of super retarding agent in the proportion ration by setting curing temperature high since outdoor curing is about 6 hours faster than standard curing, which means the temperature of the concrete will be higher than the temperature of the surrounding environment, due to its high hydration heat when applying in a construction site. The compressive strength of super retarding concrete appears to be lower than normal concrete due to the retarding action in the early stage. However, as the time goes by, the compressive strength gets higher, and by the 28th day the strength becomes the same or higher than normal concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.458-461
• /
• 2004

The column for Steel Framed Reinforced Concrete Structure (SFRCS) and the column for Reinforced Concrete Structure (RCS) could be the most common building structure. The increasing of the need for massive space hasaffected the size of building components for supporting the massive structure. However, the changing of components size makes inefficient space of building. Hence. to meet the need for acquiring efficient space comparing the budget and cost the new structure method, Concrete Filled Tube Steel (CFT), was developed. CFT is the structure for which steel tube instead of other materials such as wood for holding concrete is used. The most benefit of this one is to help in reducing the size of the building components and local buckling because of tube steel holding concrete. For this reason, this research will examine the probability of applying CFT on construction sites by using the concrete $(800kg/cm^2)$ especially for CFT through the data from the real size mock-up.

• International Journal of Concrete Structures and Materials
• /
• v.18 no.3E
• /
• pp.165-171
• /
• 2006

Environment-friendly materials are increasingly used as building construction materials nowadays, and the market share of those is growing. Accordingly, the research and developments in terms of environmental value are progressing steadily now. The main characteristics of environmental products are far-infrared radiation, negative-ion emission, electromagnetic wave shielding, and antimicrobial property. These products are often used in mortar and as spray on the finishing material. Nevertheless, there are hardly any research on the functional properties of concrete, the main material in construction field. Thus, we evaluated such basic properties of concrete as slump, compressive strength and air content while using such functional materials as sericite, wood-pattern sandstone, carbon black and nano-metric silver solution to focus on their functional properties like far-infrared radiation, negative ion emission, electro magnetic wave shielding, and antimicrobial activity in this research. The results indicated that the most useful material in the functional materials was carbon black. Sericite and nano-metric silver solution had a little effect on the functional property. Moreover, although wood-pattern sandstone had very high functional property, it exhibited too low compressive strength to be applied, to concrete as a factory product. Antimicrobial property of nano-metric silver solution in the concrete was not clear demonstrated, but if these specimens were to be aged in $CO_2$ gas for a long time, it might be apparent.

• Journal of the Korea Institute of Building Construction
• /
• v.5 no.2 s.16
• /
• pp.153-159
• /
• 2005

This study is to choose the optimal mixture and to analyze the sensibility properties of High strength concrete and mass concrete to apply the high rising building. The main experimental variables were water/binder ratio $39\%,\;33\%,\;35\%\;and\;37\%$, replacement ratio of fly ash $5\%,\;10\%\;and\;15\%$, in the high strength concrete and water/binder ratio $39\%,\;41\%\;and\;43\%$, replacement ratio of fly ash $10\%,\;20\%\;and\;30\%$, in the man concrete. According to the test results, the principal conclusions are summarized as follows. 1) The slump(or slump flow) and air content of fresh concrete were found to be the highest in the elapsed time 30 minutes. 2) The optimal mixture conditions are W/B $40\%$, FA $25\%$ in the mass concrete and W/B $33.4\%$, FA $15\%$ in the high strength concrete. 3) The ranges of sensibility are satisfied in the moisture content ${\pm}l\%\;and\;S/a\;{\pm}2\%$.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.04a
• /
• pp.142-147
• /
• 1993

In the reinforced concrete structure, as the height of building structure increases, the accurate estimation of differential column shortening is important factor in the structural design. In this study, the analysis of column shortening is applied to 36-story building structure to be built in time. As a result, it may found that, as the difference of compressive stress become larger, differential shortening effect due to creep and shrinkage are more signicant factor to structural designer.

• Journal of the Korea Institute of Building Construction
• /
• v.7 no.4
• /
• pp.133-138
• /
• 2007

This research goes into the field application cases about Flat slab concrete divide placing construction for the Multi-purpose Apartment. It is important to investigate sufficiently when mass concrete is applied to the substituted divide placing and admixture(blast furnace slag and fly ash). In addition, it is improved on the concrete quality by the job mix design which can decrease cracks caused by the heat of hydration, by the good compactability and the substitution of admixture that can prevent segregation when concrete is poured, and by the good conditioned fluidity which makes the efficiency of building construction. After considering the stated above, the sufficient prior consideration is important for a quality Improvement plan at the field use concrete of the Mass Concrete when divide placing and admixture are substituted and applied.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.1071-1076
• /
• 2001

As a rule, in case of CFT for high-rise building, high strength concrete is required since it should have high fluidity, segregation resistance and large proportion of cement per unit considering the filling beneath the diaphragm. However, regarding the low-rise building under 20 stories, it is somewhat difficult to use high strength concrete. This is a fundamental study to develop a concrete with normal strength and high fluidity for CFT of low-rise building, whose Purposes are in speculating several kinds of changes in concrete's characteristics through various experiments and offering basic documents for practicalization in site and production through mock-up test.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.66-67
• /
• 2014

Design and construction of freeform building technologies are being implemented to reduce time and cost due to the development of materials and equipments. However, production of freeform concrete segments takes much more time and manpower than typical due to disposable mold and various shape. Therefore, manufacturing technology of freeform concrete segments need to be developed for securing economic and constructive feasibility. The objective of this study is development of efficient casting technology for freeform concrete segments in a short time. This technology includes details about the fluidity of concrete and the sectional shape of freeform concrete segments. And problem of cost and time can be solved. Also, mold can be reusable and freeform concrete segments will be produced quickly and accurately. After this study, productivity study for validation will continue through prototype development and example application.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.11a
• /
• pp.77-80
• /
• 2009

Because buildings which apply color that is various to concrete recently are introduced, value as design element of building is rising gradually in townscape. Even if expense is increased according as importance of concrete that have variety of design because do such social background and connection is emphasized, development of color concrete is pressing. Therefore, in this research, examined concrete physical & chemical characteristics by use of acid agent as part of research to embody diverse surface color of cement material. Here, embodiment of various color by unique color that stained hydrate has as that Color Concrete forms stained oxide that react with hydrate within concrete spreading stained agent that contain acid and metallic-ion in matrix that have cement ingredient on the surface is available.