• 한국도로학회:학술대회논문집
• /
• 2010.03a
• /
• pp.235-240
• /
• 2010

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.647-650
• /
• 2005

This paper is to investigate the shrinkage properties of ultra high strength concrete(UHSC) incorporating $5\%$ of expansive additives(EA) along with $1\%$ of shrinkage reducing agent(SRA). UHSC subjected to steam curing and incorporated with steel fiber exhibited higher compressive strength than control UHSC by as much as50MPa at 7days, while at 28days, noticeable change in compressive strength was not observed between UHSC mixtures. Control UHSC subjected to steam curing had a $922{\times}10^6$ of autogenous shrinkage strain value, which was 6.7 times of drying shrinkage strain value at 42 days. The combination of EA and SRA resulted in a decrease in autogenous shrinkage by as much as half of control mixture. Steam curing contributed to the reduction of autogenous shrinkage by as much as $11\%$ compared with that of standard curing.

• International Journal of Concrete Structures and Materials
• /
• v.2 no.2
• /
• pp.99-105
• /
• 2008

Southern exposure test specimens were used to evaluate corrosion performance of epoxy-coated reinforcing bars in chloride contaminated concrete by electrochemical impedance spectroscopy method. The test specimens with conventional bars, epoxy-coated bars and corrosion inhibitors were subjected 48 weekly cycles of ponding with sodium chloride solution and drying. The polarization resistance obtained from the Nyquist plot was the key parameter to characterize the degree of reinforcement corrosion. The impedance spectra of specimens with epoxy-coated bars are mainly governed by the arc of the interfacial film and the resistance against the charge transfer through the coating is an order of magnitude higher than that of the reference steel bars. Test results show good performance of epoxy-coated bars, although the coatings had holes simulating partial damage, and the effectiveness of corrosion-inhibiting additives. The corrosion rate obtained from the impedance spectroscopy method is equivalent to those determined by the linear polarization method for estimating the rate of corrosion of reinforcing steel in concrete structures.

• Journal of the Korea Concrete Institute
• /
• v.16 no.3 s.81
• /
• pp.369-374
• /
• 2004

Calcium sulfoalumiante(CSA) was prepared for using natural calcite($CaCO_3$) and industrial by-products and wastes, such as $Al(OH)_3,\;CaSO_4{\cdot}2H_2O$. The mixture of raw materials was fired at 20, 400, 600, $1200^{\circ}C$ for 1h and cooled rapidly in air. The cement replaced by 10 wt% $C_4A_3S$ expansive additives was investigated by the measurement of the hydration products and compressive strength, setting time, expansion at wet curing condition. $C_4A_3S$ was found in x-ray diffraction pattern over the temperature $1200^{\circ}C$. The setting time or the cement pastes added clinkers fired at different temperature was shorter than ordinary portland cement. The compressive strength was higher than the ordinary portland cement about 20~30%. The mainly hydration products were ettringite, and $Ca(OH)_2$. The expansion due to the formation of ettringite during hydration decreased the drying shrinkage of hardened cement rather than the ordinary portland cement.

• Computers and Concrete
• /
• v.11 no.4
• /
• pp.337-350
• /
• 2013

The sensitivity of compressive strength of no-slump concrete to its ingredient materials and proportions, necessitate the use of robust models to guarantee both estimation and generalization features. It was known that the problem of compressive strength prediction owes high degree of complexity and uncertainty due to the variable nature of materials, workmanship quality, etc. Moreover, using the chemical and mineral additives, superimposes the problem's complexity. Traditionally this property of concrete is predicted by conventional linear or nonlinear regression models. In general, these models comprise lower accuracy and in most cases they fail to meet the extrapolation accuracy and generalization requirements. Recently, artificial intelligence-based robust systems have been successfully implemented in this area. In this regard, this paper aims to investigate the use of optimized support vector machine (SVM) to predict the compressive strength of no-slump concrete and compare with optimized neural network (ANN). The results showed that after optimization process, both models are applicable for prediction purposes with similar high-qualities of estimation and generalization norms; however, it was indicated that optimization and modeling with SVM is very rapid than ANN models.

• Computers and Concrete
• /
• v.23 no.3
• /
• pp.189-201
• /
• 2019

Recent advances in the concrete technology are aiding in minimizing the use of conventional materials by substituting by-products of various industries and energy sources. A large amount of stone waste i.e., dust and slurry form both are being originated during natural stone processing and causing deadily effects on the environment. The disposal problem of stone waste can be resolved effectively by using waste in construction industries. In present work, Kota stone slurry powder, as a substitution of cement was used along with accelerators namely calcium nitrate and triethanolamine as additives, to study their impact on various properties of the concrete mixtures. Kota stone slurry powder (7.5%), calcium nitrate (1%) and triethanolamine (0.05%) were used separately as well in combination in different concrete mixtures. Mechanical Strength, modulus of elasticity and electrical resistivity of concrete specimens of different mix proportions under water curing were studied experimentally. The durability properties in terms of strength and electrical resistivity against sulphate and chloride solution attack at various curing ages were also studied experimentally. Results showed that accelerators and Kota stone slurry powder separately enhanced the mechanical strength and electrical resistivity; but, their combination decreased strength at all curing ages. The durability of concrete specimens was also affected under the exposure to chemical attack too. Kota stone slurry powder found to be the most effective material among all materials. Material characterization was also done to study the microstructural properties.

• Journal of the Korea Concrete Institute
• /
• v.18 no.2 s.92
• /
• pp.205-211
• /
• 2006

The objective of this study was to evaluate the durability of low shrinkage high performance concrete(LSHPC), which was combined with expansive additives and shrinkage reducing admixtures. We tested for not only LSHPC but also high performance concrete(HPC) and normal concrete(NC) to be compared with the durability of LSHPC. HPC was made in the same water-binder ratio of LSHPC without expansive additives and shrinkage reducing admixture. As a result, it was found that LSHPC had higher compressive and tensile strength than that of HPC. LSHPC showed more excellent performance than HPC and NC in the case of resistance to chloride ion penetration and resistance to carbonation and also showed nearly 100 durability factor in the freeze-thawing test with 500 cycles. From the examination about the watertightness and the pore distribution, it was found that the durability of LSHPC was improved because its hardened cement paste is organized closer. So we can conclude that when LSHPC is applied to structures in field, it is possible to reduce the shrinkage and crack in concrete and improve the durability.

• Advances in concrete construction
• /
• v.11 no.2
• /
• pp.163-171
• /
• 2021

This paper studies the effect of using multi-scale reinforcement additives on mechanical strengths, damage performance, microstructure, and water absorption of cementitious composites. Small dosages of carbon nanotubes (CNTs) or polypropylene (PP) microfibers; 0.05%, 0.1%, and 0.2% by weight of cement; were added either separately or simultaneously into cement mortar. The experimental results show the ability of these additives to enhance the mechanical behavior of the mortar. The best improvement in compressive and flexural strengths of cement mortar reaches 28% in the case of adding a combination of 0.1% CNTs and 0.2% PP fibers for compression, and a combination of 0.2% CNTs and 0.2% PP fibers for flexure. Adding CNTs does not change the brittle mode of failure of plain mortar whereas the presence of PP fibers changes it into ductile failure and clearly enhances the fracture energy of the specimens. Scanning electron microscopic (SEM) images of the fracture surfaces highlights the role of CNTs in improving the adhesion between the PP fibers and the hydration products and thus enhance the ability of the fibers to mitigate cracks propagation and to enhance the mechanical performance of the mortar.

• International Journal of Concrete Structures and Materials
• /
• v.11 no.2
• /
• pp.391-401
• /
• 2017

In this study, the effects of water-to-binder (W/B) ratio and replacement ratio of blast furnace slag (BFS) on the compressive strength of concrete were first investigated to determine an optimized mixture. Then, using the optimized high-strength concrete (HSC) mixture, hooked steel fibers with various aspect ratios and volume fractions were used as additives and the resulting mechanical properties under compression and flexure were evaluated. Test results indicated that replacement ratios of BFS from 50 to 60% were optimal in maximizing the compressive strength of steam-cured HSCs with various W/B ratios. The use of hooked steel fibers with the aspect ratio of 80 led to better mechanical performance under both compression and flexure than those with the aspect ratio of 65. By increasing the fiber aspect ratio from 65 to 80, the hooked steel fiber volume content could be reduced by 0.25% without any significant deterioration of energy absorption capacity. Lastly, complete material models of steel-fiber-reinforced HSCs were proposed for structural design from Lee's model and the RILEM TC 162-TDF recommendations.

• Computers and Concrete
• /
• v.10 no.4
• /
• pp.391-407
• /
• 2012

Utilization of supplementary cementing materials (SCM) by the cement industry, as a highly promising solution of sustainable cement development aiming to reduce carbon dioxide emissions, necessitates a more thorough evaluation of these types of materials on concrete durability. In this study a comparative assessment of the effect of SCM on concrete durability, of every cement type as defined in the European Standard EN 197-1 is taking place, using a software tool, based on proven predictive models (according to performance-related methods for assessing durability) developed and wide-validated for the estimation of concrete service life when designing for durability under harsh environments. The effect of Type II additives (fly ash, silica fume) on CEM I type of cement, as well as the effect of every Portland-composite type of cement (and others) are evaluated in terms of their performance in carbonation and chloride exposure, for a service life of 50 years. The main aim is to portray a unified and comprehensive evaluation of the efficiency of SCM in order to create the basis for future consideration of more types of cement to enter the production line in industry.