• Structural Engineering and Mechanics
• /
• 제44권6호
• /
• pp.753-762
• /
• 2012

The ratcheting characteristics of cylindrical shell under cyclic axial loading are investigated. The specimens are subjected to stress-controlled cycling with non-zero mean stress, which causes the accumulation of plastic strain or ratcheting behavior in continuous cycles. Also, cylindrical shell shows softening behavior under symmetric axial strain-controlled loading and due to the localized buckling, which occurs in the compressive stress-strain curve of the shell; it has more residual plastic strain in comparison to the tensile stress-strain hysteresis curve. The numerical analysis was carried out by ABAQUS software using hardening models. The nonlinear isotropic/kinematic hardening model accurately simulates the ratcheting behavior of shell. Although hardening models are incapable of simulating the softening behavior of the shell, this model analyzes the softening behavior well. Moreover, the model calculates the residual plastic strain close to the experimental data. Experimental tests were performed using an INSTRON 8802 servo-hydraulic machine. Simulations show good agreement between numerical and experimental results. The results reveal that the rate of plastic strain accumulation increases for the first few cycles and then reduces in the subsequent cycles. This reduction is more rapid for numerical results in comparison to experiments.

• 콘크리트학회논문집
• /
• 제23권1호
• /
• pp.67-75
• /
• 2011

이 연구에서는 UHPCC에서 강섬유 혼입률이 압축거동에 미치는 영향에 관한 연구를 수행하였으며, 그 결과로부터 UHPCC에 적용가능한 압축거동 모델을 제시하고자 하였다. 섬유혼입률 0~5 vol.%에 대해 실험을 수행한 결과, 섬유혼입률이 증가함에 따라 압축강도 및 그 때의 극한변형률 및 탄성계수가 증가하는 경향을 확인할 수 있었다. 이와 같은 결과는 100 MPa 이하의 강섬유보강 콘크리트에 대한 기존 연구 결과들과 비교했을 때, 압축강도는 섬유보강효과가 거의 동일한 경향을 나타내는 반면, 극한변형률과 탄성계수에 대한 섬유보강효과는 상대적으로 훨씬 적게 나타났다. 섬유혼입률이 증가함에 따른 UHPCC의 압축강도, 극한변형률 및 탄성계수의 변화를 섬유보강지수(RI)를 이용한 선형관계식으로 표현하였다. UHPCC의 압축거동에 대한 섬유보강효과는 거동의 형상에 전혀 영향을 미치지 않으며, 다만 압축강도와 그 때의 극한변형률 및 탄성계수에 영향을 미치는 점을 고려하여 UHPCC의 압축응력-변형률 관계를 제시하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.263-264
• /
• 2012

In this study, the ultra high strength concrete which have 100, 150, 200MPa took the heat from 20℃ to 70 0℃ and the 0, 20% stress in normal condition's to evaluate stress-strain, residual compressive strength and thermal expansion deformation were evaluated. The heating speed of specimen was 0.77℃/min 20~50℃, 50℃ before the target temperature, and the other interval's heating speed was 1℃/min. As a result, the stress-strain curve of non-load specimen showed the liner behavior at high temperature when the specimen's strength increased more. If ultra high strength concrete got loads, its compressive strength tended to decrease different from the normal strength concrete. The thermal expansion deformation was expanded from a vitrification of quartz over 500℃. however, over the 600℃, it was shrinked because of the dehydration of the combined water.

• 한국농공학회논문집
• /
• 제52권1호
• /
• pp.51-59
• /
• 2010

The cemented sand and gravel (CSG) method is a construction technique that adds cement and water to rock-like materials, such as rivered gravel or excavation muck which that can be obtained easily at areas adjacent to dam sites. This study was performed to evaluate the unconfined compressive strength properties and freezing and thawing resistance of CSG materials with unit cement content. The three types of CSG-80, CSG-100 and CSG-120 with cement content were designed to evaluate the optimum water content, dry density, strength, stress-strain, micro structure and durability factor. As the results, the optimum water content ratio with cement content showed almost similar tendency, and the unconfined compressive strength and dry density increased as cement content increases. The strength ratio of 7 days for 28 days were in the range of 55~61 % and the strain ratio in stress-strain curve were in the range of 0.8~1.6 % nearby maximum strength in 28 days. It is expected that this study will contribute to increasing application of CSG method as well as to increasing the utilizing of CSG materials as a environmentally friendly CSG method.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.237-240
• /
• 2004

High strain-rate deformation behavior of NiAl/Ni micro-laminated composites was characterized by split hopkins on pressure bar(SHPB). When the strain rate increased, the compressive stress of micro-laminated composites were increased a little. When the intermetallic volume fraction increased, the compressive stress of micro-laminated composites increased linearly irrespective of strain rate. Absorbed energy during the quasi-static and SHPB tests was calculated from the integrated area of stress-strain curve. Absorbed energy of micro-laminated composites deviated from the linearity in terms of the intermetallic volume fraction but merged to the value of intermetallic as the strain rate increased. This was due to high tendency of intermetallic layer for the localization of shear deformation at high strain rate. Microstructure showing adibatic shear band(ASB) confirmed that the shear strain calculated from the misalignment angle of each layer increased and ASB width decreased when the intermetallic volume fraction. Simulation test impacted by tungsten heavy alloy cylinder resulted that the absorbed energies multiplied by damaged volume of micro-laminated composites were decreased as the intermetallic volume fraction increased. Fracture mode were changed from delamination to single fracture when the intermetallic volume fraction and this results were good matched with previous results[l] obtained from the fracture tests.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1491-1494
• /
• 2003

A specific experimental method, the Split Hopkinson Pressure Bar (SHPB) technique has been widely used to determine the dynamic material properties under the impact compressive loading conditions with strain-rate of the order of 103/s∼104/s. This type of test procedure has been used to examine the dynamic response of materials in various modes of testing. In this paper, dynamic deformation behaviors of rubber materials widely used for the isolation of vibration from varying structures under dynamic loading are determined using a Split Hopkinson Pressure Bar technique.

• Journal of Mechanical Science and Technology
• /
• 제20권6호
• /
• pp.819-827
• /
• 2006

The stress-strain relation of aluminum (Al) alloy foam cell wall was evaluated by the instrumented sharp indentation method. The indentation in a few micron ranges was performed on the cell wall of Al-alloy foam having a composition or Al-3wt.%Si-2wt.%Cu-2wt.%Mg as well as its precursor (material prior to foaming). To extract the stress-stram relation in terms of yield stress ${\sigma}_y$, strain hardening exponent n and elastic modulus E, the closed-form dimensionless relationships between load-indentation depth curve and elasto-plastic property were used. The tensile properties of precursor material of Al-alloy foam were also measured independently by uni-axial tensile test. In order to verify the validity of the extracted stress-strain relation, it was compared with the results of tensile test and finite element (FE) analysis. A modified cubic-spherical lattice model was proposed to analyze the compressive behavior of the Al-alloy foam. The material parameters extracted by the instrumented nanoindentation method allowed the model to predict the compressive behavior of the Al-alloy foam accurately.

• 콘크리트학회논문집
• /
• 제17권5호
• /
• pp.843-852
• /
• 2005

Presently, test results and stress-strain models for poorly confined high-strength columns, more specifically for columns with a tie volumetric ratio smaller than $2.0\%$, are scarce. This paper presents test results loaded in axial direction for square reinforced concrete columns confined by various volumetric ratio lateral ties including low-volumetric ratio. Test variables include concrete compressive strength, tie yield strength, tie arrangement type, and tie volumetric ratio. Local strains measured using strain gages bonded to an acryl rod. For square RC columns confined by lateral ties, the confinement effect was efficiently improved by changing tie arrangement type from Type-A to Type-B. A method to compute the stress in lateral ties at the concrete peak strength and a new stress-strain model for the confined concrete are proposed. Over a wide range of confinement parameters, the model shows good agreement with stress-strain relationships established experimentally.

• 콘크리트학회논문집
• /
• 제23권3호
• /
• pp.365-376
• /
• 2011

현행 콘크리트구조설계기준(2007)은 콘크리트 구조물의 설계에 적용하는 콘크리트의 압축응력 분포로 ACI 318의 등가 직사각형 응력 분포를 규정하고 있다. 단면의 휨강도 해석에는 등가 직사각형 응력 분포가 충분하겠지만, 성능 중심 설계의 한계 상태 검증에는 실제와 가까운 압축응력-변형률 관계가 필요하다. 또 등가 직사각형 응력 분포는 고강도 콘크리트 기둥의 휨강도 해석에 비안전측의 결과를 준다는 것이 알려져 있으므로, 이를 대신하는 새로운 응력 분포 모델이 필요하다. 이 연구에서는 Eurocode와 일본 토목학회의 설계기준에서 채택하고 있는 포물선-직선 형상의 새로운 모델을 제안하였다. 이 응력 분포 모델은 이 연구에서 수행된 압축응력 분포 실험과 타 연구자들의 실험 결과를 분석하여 도출된 것으로서, 보통 강도뿐만 아니라 고강도 콘크리트를 포함한 것이다. 제안 모델의 특성은 미국 ACI 318, 캐나다 CSA, 유럽의 Eurocode, 일본 토목학회 설계기준의 응력 분포 모델과 함께 실험 결과와 비교하여 정리하였다.

• International Journal of Aeronautical and Space Sciences
• /
• 제18권3호
• /
• pp.436-449
• /
• 2017

In this paper, the damage and failure behavior of triaxially braided textile composites was studied using progressive failure analysis. The analysis was performed at both micro and meso-scales through iterative cycles. Stress based failure criteria were used to define the failure states at both micro- and meso-scale models. The stress-strain curve under uniaxial tensile loading was drawn based on the load-displacement curve from the progressive failure analysis and compared to those by test and computational results from reference for verification. Then, the detailed failure initiation and propagation was studied using the verified model for both tensile and compression loading cases. The failure modes of each part of the model were assessed at different stages of failure. Effect of ply stacking and number of unit cells considered were then investigated using the resulting stress-strain curves and damage patterns. Finally, the effect of matrix plasticity was examined for the compressive failure behavior of the same model using elastic, elastic - perfectly plastic and multi-linear elastic-plastic matrix properties.