• 한국건설순환자원학회논문집
• /
• 제10권4호
• /
• pp.367-375
• /
• 2022

순환 잔골재 혼합비율에 따른 압축강도는 설계기준강도별 보통콘크리트 대비 순환 잔골재 혼합비율에 따라 유사하거나 다소 낮은 강도 발현을 보였으며, 순환 잔골재 혼합비율이 증가할수록 압축강도는 감소하는 경향을 보였다. 재령일이 증가할수록 강도저하는 발생하지 않았으며, 설계기준강도 대비 강도 발현이 가능할 것으로 판단된다. 순환 잔골재 15 %, 20 %, 25 %로 혼합비율에 따른 순환골재 콘크리트의 길이변화 및 동결융해에 대한 내구특성은 보통콘크리트와 유사한 경향으로 나타났다. 콘크리트용 순환 잔골재의 비율은 총 골재량의 25 %(총잔골재의 50 %)까지 적용하면 슬럼프 및 공기량에 문제가 없을 것으로 판단되며, 설계기준강도에 따른 분체량과 단위수량 및 공기연행제량에 대한 관리가 필요할 것으로 판단된다.

• Geomechanics and Engineering
• /
• 제17권1호
• /
• pp.57-67
• /
• 2019

Water-induced strength reduction is one of the most critical causes for rock deformation and failure. Understanding the effects of water on the strength, toughness and deformability of rocks are of a great importance in rock fracture mechanics and design of structures in rock. However, only a few studies have been conducted to understand the effects of water on fracture properties such as fracture toughness, crack propagation velocity, consumed energy, and microstructural damage. Thus, in this study, we focused on the understanding of how microscale damages induced by water saturation affect mesoscale mechanical and fracture properties compared with oven dried specimens along three notch orientations-divider, arrester, and short transverse. The mechanical properties of calcite-cemented sandstone were examined using standard uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) tests. In addition, fracture properties such as fracture toughness, consumed energy and crack propagation velocity were examined with cracked chevron notched Brazilian disk (CCNBD) tests. Digital Image Correlation (DIC), a non-contact optical measurement technique, was used for both strain and crack propagation velocity measurements along the bedding plane orientations. Finally, environmental scanning electron microscope (ESEM) was employed to investigate the microstructural damages produced in calcite-cemented sandstone specimens before and after CCNBD tests. As results, both mechanical and fracture properties reduced significantly when specimens were saturated. The effects of water on fracture properties (fracture toughness and consumed energy) were predominant in divider specimens when compared with arrester and short transverse specimens. Whereas crack propagation velocity was faster in short transverse and slower in arrester, and intermediate in divider specimens. Based on ESEM data, water in the calcite-cemented sandstone induced microstructural damages (microcracks and voids) and increased the strength disparity between cement/matrix and rock forming mineral grains, which in turn reduced the crack propagation resistance of the rock, leading to lower both consumed energy and fracture toughness ($K_{IC}$).

• 대한토목학회논문집
• /
• 제26권4A호
• /
• pp.767-774
• /
• 2006

본 연구에서는 상동지역 중석광 광미를 콘크리트용 혼화재료로 사용하기 위한 연구의 일환으로 자기충전콘크리트의 분체로서 적용가능성을 검토하였다. 상동지역 중석광 광미를 혼합한 시멘트 페이스트의 유변학적 특성을 검토하기 위하여 구속수비 및 점도계를 이용하여 평균소성점도 및 항복응력을 측정하였으며 가상수막이론을 적용하여 검토하였다. 그리고 광미를 혼합한 자기충전콘크리트의 자기충전성 평가는 일본 토목학회에서 제시한 기준안을 적용하여 검토하였으며, 역학적 특성은 압축강도, 쪼갬인장강도 및 탄성계수를 측정하여 검토하였다. 실험결과 광미의 혼합률이 증가함에 따라 구속수비와 평균소성점도는 감소하였으며, 가상수막 두께는 증가하는 경향을 나타냈다. 또한, 광미를 혼합한 자기충전콘크리트의 자기충전성 검토 결과는 유동성 평가기준인 슬럼프 플로우 500 mm 도달시간의 경우 광미의 혼합률이 증가함에 따라 다소 증가하였고 재료 분리저항성 및 충전성 평가 결과는 기준을 만족하는 경향을 나타내고 있었다. 역학적 특성 검토 결과는 압축강도의 경우 광미의 혼합률이 증가함에 따라 압축강도는 감소하였고, 쪼갬인장강도 및 탄성계수는 보통 콘크리트의 유사한 경향을 나타내었다.

• 지질공학
• /
• 제14권1호
• /
• pp.61-69
• /
• 2004

석재는 주로 장식용 및 조각용으로 사용되며 따라서 우수한 물성도 골고루 지녀야 한다. 다양한 물성 중에서 공극계수가 석재의 유용성을 지배하므로 공극의 성질과 연관하여 석재의 품질구분 설정을 시도하였다. 이 연구에서는 화강암질암류 및 화강암질편마암의 심도별 시추코아 시료가 사용되었다. 공극률과 흡수율의 상관도에서 문경 화강암질편마암($Gn_1$)의 측정치 범위가 가장 넓은 분포상을 보이며, 포천화강암($Gr_2$), 문경화강암($Gr_1$)의 순으로 그 범위는 감소한다. 각 암체의 강도는 변질도에 따라 변화한다. 또한 압축강도와 인장강도와의 상관성에서도 측정치의 범위는 $Gn_1$, $Gr_2$ 그리고 $Gr_1$의 순으로 감소한다. 석재의 품질구분 설정에 있어 공극률이 대표적인 물성으로 채택되어 여러 물성에 대한 상대적인 평가가 이루어졌다. 공극률(n)-비중(G), 흡수율(Ab), 압축강도(${\sigma}_c$), 인장강도(${\sigma}_t$), 쇼아경도(Hs) 그리고 탄성계수($E_{t}$)와의 상관도에서 각 등급별 기준이 설정된다.

• 한국건축시공학회지
• /
• 제11권6호
• /
• pp.587-596
• /
• 2011

폴리머 시멘트 모르타르를 긴급공사의 보수 보강 재료로 사용할 때, 초속경시멘트와 혼입하여 사용함으로써 시멘트의 빠른 응결과 시멘트 매트릭스 내부에서 형성된 폴리머 필름의 작용이 물리적 성질과 내구성을 개선시킬 수 있다. 또한 각종 혼화재료를 혼입함으로써 매트릭스 내부 공극을 충전하여 성질을 개선시킬 수 있는데, 양생방법이 큰 영향을 미칠 수 있다. 본 연구에서는 속경성 SBR 시멘트 모르타르의 압축강도와 휨강도에 영향을 미칠 수 있는 혼화재료와 양생조건에 관하여 실험을 실시하여 그 영향성을 평가하고자 하였다. 본 연구결과, 초속경시멘트 모르타르에 SBR을 혼입함으로써 휨강도와 압축강도가 크게 개선되었으며, 여기에 메타카올린을 혼입함으로써 보다 더 강도를 증진시킬 수 있었다. 또한 양생방법에 있어서도 SBR을 사용한 경우에는 표준양생에서, SBR을 사용하지 않은 경우에는 수중양생에서 강도발현이 크게 나타났다.

• 한국환경복원기술학회지
• /
• 제7권6호
• /
• pp.19-28
• /
• 2004

Segmental Retaining Wall(SRW) has been variously applying in Civil and Architecture construction. Recently, the application of environmental element in all type's structures came to essential requirement, and the construction cases of retaining wall using reinforced soil and block are more increased than the past. But, this trend more widely was spread environmental element as landscape work for the backside of reinforced retaining wall as well as block itself. New environmental block, Greenstone Block, developed to apply of this tendency. The retaining wall system using Greenstone can be environmental constructing at both block itself and backside of retaining wall. The material tests, the axial compressive strength test of block and bending test of fiber-pipe, exercised to design and construction of vertical SRW, which were satisfied NCMA standard. Through this procedure, Rewall (ver 1.0) was developed, which can be automation design of SRW including internal stability, external stability and local stability. And these can be considered setback of retaining wall, as well the examples of vertical retaining wall using block presented to satisfying the follows; strength of reinforced geotextile, height of retaining wall, surcharge, types of backfill and groundwater level etc. Many problems investigated on after or before of construction were due to local failure, insufficiency of bearing capacity and groundwater level. Especially, the local failure was many occurred to during compaction or after construction, and the cases of SRW construction is similar to the results of model test on vertical SRW.

• International Journal of Concrete Structures and Materials
• /
• 제7권1호
• /
• pp.79-93
• /
• 2013

One of the biggest problems affecting bridges is the transverse cracking and deterioration of concrete bridge decks. The causes of early age cracking are primarily attributed to plastic shrinkage, temperature effects, autogenous shrinkage, and drying shrinkage. The cracks can be influenced by material characteristics, casting sequence, formwork, climate conditions, geometry, and time dependent factors. The cracking of bridge decks not only creates unsightly aesthetic condition but also greatly reduces durability. It leads to a loss of functionality, loss of stiffness, and ultimately loss of structural safety. This investigation consists of field, laboratory, and analytical phases. The experimental and field testing investigate the early age transverse cracking of bridge decks and evaluate the use of sealant materials. The research identifies suitable materials, for crack sealing, with an ability to span cracks of various widths and to achieve performance criteria such as penetration depth, bond strength, and elongation. This paper also analytically examines the effect of a wide range of parameters on the development of cracking such as the number of spans, the span length, girder spacing, deck thickness, concrete compressive strength, dead load, hydration, temperature, shrinkage, and creep. The importance of each parameter is identified and then evaluated. Also, the AASHTO Standard Specification limits liveload deflections to L/800 for ordinary bridges and L/1000 for bridges in urban areas that are subject to pedestrian use. The deflection is found to be an important parameter to affect cracking. A set of recommendations to limit the transverse deck cracks in bridge decks is also presented.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1996년도 봄 학술발표회 논문집
• /
• pp.172-179
• /
• 1996

Recently, the broken concrete lumps resulting from the demolition of concrete structures are creshed for reuse as aggregates(i.e. recycled fine and gravel). And also, in the processing of crusing, the recycled powder of an equivalent of between 20% to 30% by wt.% of the broken concrete lumps is generated. The extensive research of recycled concrete aggregates has been carried out in various parts of the world. But less reseatch on the reuse of recycled concrete powder has been carried out. It is the purpose of this report that the study on the quality evaluation of recycled aggregates for recycled concrete. In specially, this report deals with the properties such as flow, compressive strength, bending strength, drying shrinkage and wight loss rate of mortars replaced standard fine aggregate with recycled powders at the rate of 3, 7, 15, 20 and 30 wt.%. Since the characteristics of recycled mortars with the recycled powders were comparable to those of the normal mortar without the recycled powders as described above, its concretes could be found extensive application in such field as concrete products.

• Structural Engineering and Mechanics
• /
• 제83권1호
• /
• pp.79-92
• /
• 2022

In this paper, the impact of a vernacular pozzolanic kaolinite mine on concrete alkali-silica reaction and strength has been evaluated. For making the samples, kaolinite powder with various levels has been used in the quality specification test of aggregates based on the ASTM C1260 standard in order to investigate the effect of kaolinite particles on reducing the reaction of the mortar bars. The compressive strength, X-Ray Diffraction (XRD) and Scanning Electron Microscope (SEM) experiments have been performed on concrete specimens. The obtained results show that addition of kaolinite powder to concrete will cause a pozzolanic reaction and decrease the permeability of concrete samples comparing to the reference concrete specimen. Further, various machine learning methods have been used to predict ASR-induced expansion per different amounts of kaolinite. In the process of modeling methods, optimal method is considered to have the lowest mean square error (MSE) simultaneous to having the highest correlation coefficient (R). Therefore, to evaluate the efficiency of the proposed model, the results of the support vector machine (SVM) method were compared with the decision tree method, regression analysis and neural network algorithm. The results of comparison of forecasting tools showed that support vector machines have outperformed the results of other methods. Therefore, the support vector machine method can be mentioned as an effective approach to predict ASR-induced expansion.

• 펄프종이기술
• /
• 제46권6호
• /
• pp.16-25
• /
• 2014

This study was investigated in optimum condition of pulping of ramie and the mechanical properties of non-woven fabric for the performance of ramie/cotton panty liner. The result of pulping condition on ramie was most suitable for type I (mixed NaOH with $Na_2CO_3$ in 30%:70%). The sample (I) was showed yield value of 68.2% and the best fibrillation and lignin removal rate. The non-woven fabrics of ramie/cotton were made in range of ramie content of 0, 15 and 30%. As ramie content increased, so were increased in air permeability, compressive strength and compression recovery rate. But surface roughness and compressional energy were decreased. Therefore, the non-woven fabrics of ramie/cotton are very suitable in hygienic goods for female panty liner. The ramie panty liner showed a little decrease in absorption and strength, as increasing the amount of ramie. But the performance of ramie panty liner was appeared beyond standard values used by usual panty liner.