• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.668-671
• /
• 2004

Recently, the concern for mechanical properties at early age concrete are increasing because of the importance of the thermal stress and the determination of removal time of form work and prestressing work. In this study, an estimation for the development of compressive strength and elastic modulus with age in concretes isothermally cured $(10^{\circ}C,\;20^{\circ}C)$ and having W/C ratio of 30, 40, and $50\%$ were investigated. According to experiment results, the development of compressive strength and elastic modulus shows higher values at early ages as the W/C ratio decreases and curing temperature increases. When the maturity concept, for estimation of the strength, is adopted, a modification for W/C ratio is required at early ages.

• Journal of the Korea Concrete Institute
• /
• v.16 no.4 s.82
• /
• pp.459-465
• /
• 2004

The present paper is intended to investigate the influence of materials such as cement, mineral admixture and aggregate, on the estimation of compressive strength by P type schmidt hammer. According to the results, the materials of concrete, such as the types of cement, the replacing ratio of mineral admixture, the kinds and maximum size of aggregate, hardly influence on non-destructive test by P type schmidt hammer except for alumina cement, hence, P type schmidt can be applicable to most of the concrete with a wide range. Since the correlativity between the rebound value of P type schmidt hammer and compressive strength is very favorable(above coefficient of correlation 0.96) regardless of materials, it is considered that compressive strength can be estimated comparatively exactly by P type schmidt hammer. The estimating formula of compressive strength by rebound value are derived from this experiment as following. $\cdot$Horizontal strike : Fc = 0.765RH - 5.74 (R=0.965) $\cdot$ Vertical strike Fc = 0.793RV - 8.66 (R=0.959)

• Computers and Concrete
• /
• v.20 no.6
• /
• pp.645-654
• /
• 2017

Continuing from previous studies of sustainable concrete containing environmentally friendly materials and existing modeling approach to predicting concrete properties, this study developed an estimation methodology to predicting the strength of sustainable concrete using an advanced case-based reasoning approach. It was conducted in two steps: (i) establishment of a case database and (ii) development of an advanced case-based reasoning model. Through the experimental studies, a total of 144 observations for concrete compressive strength and tensile strength were established to develop the estimation model. As a result, the prediction accuracy of the A-CBR model (i.e., 95.214% for compressive strength and 92.448% for tensile strength) performed superior to other conventional methodologies (e.g., basic case-based reasoning and artificial neural network models). The developed methodology provides an alternative approach in predicting concrete properties and could be further extended to the future research area in durability of sustainable concrete.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.5 no.1
• /
• pp.161-168
• /
• 2001

The use of composite members to improve the compressive strength of steel structure is a common practice these days and its efficiency has already been proved by several researches and experiments. The result of concrete filled circular tubular(CFCT) stub column tests is introduced in this paper. The main parameter of this test is the ratio of diameter to thickness of circular hollow section. From the test results, the effect of concrete filled in steel tube on the ultimate strength, the deformation capacity and initial stiffness are discussed. The purpose of this paper is to investigate the effect of various parameters and evaluate the compressive strength of confined concrete. It would contribute to a better understanding of CFT structure, further laboratory experimentations are needed for better accurate estimation on its effect.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.26 no.3
• /
• pp.46-58
• /
• 1984

This study was carried out to investigate the compressive strength and the other effects varying to seasons and curing days on the wet curing conditions of the plain concrete. The results obtained are summarized as follows; 1. The longer the wet curing days and the higher the temperature, the greater the compressive strength was expected. 2.。$_2$8, compressive strength of concrete at 28 days under the dry curing conditions showed a range in 64-76% of that under the wet curing conditions. 3. The seasonal variations in the compressive strength under the wet curing showed in order of summer>spring=autumn>winter, and that under the dry curing were in order of spring ≒autumn> summer> winter. 4. In order to obtain 90% of the design compressive strength, 7 days in spring or autumn and 2 weeks of the wet curing in summer were required. 5. The compressive strength of concrete under the wet curing by using wet straw bag cover was almost the same as that of water curing method. 6. Under the wet curing conditions, the higher the temperature, the greater the effect of the curing of concrete was obtained, however, the compressive strength of concrete was decreased under relatively higher (over 15$^{\circ}$ C) and lower temperature (below 4$^{\circ}$C). 7. Freezing damage was occured when temperature was below 0$^{\circ}$ C and humidity was relatively high. 8. A considerable differnce between estimation of $^{\circ}$$_2$8 from $^{\circ}$7 and measured one was appeared in case of the dry curing conditions. Oregon formula was appeared to be acceptable under the wet curing conditions. 9. In relationship between $^{\circ}$$_2$8 and $^{\circ}$7~, $^{\circ}$28=1. 52 $^{\circ}$7 under the wet curing conditions except winter season, and $^{\circ}$$_2$8 =(1.39-1, 48)$^{\circ}$7 under the dry curing conditions were shown.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.11a
• /
• pp.26-27
• /
• 2014

Study on high temperature properties of concrete and internal force estimation of structural member subjected to high temperature mainly applied high temperature strength model based on experimental results with concrete under 40MPa. However, it is reported that degradation of internal force at high temperature and spalling of ultra high strength concrete are higher than that of normal strength concrete. Therefore, this study attempts to propose compressive strength degradation model which is suitable to ultra high strength concrete comparing to existing model by evaluating high temperature properties of ultra high strength concrete.

• Journal of the Korean GEO-environmental Society
• /
• v.16 no.11
• /
• pp.5-11
• /
• 2015

The development of Controlled Low Strength Material (CLSM), which is a highly flowable material, has been performed for the application of backfill. The objective of this study is to compare the compressive strength and compressive wave velocity of CLSM according to the curing time. To investigate the characteristics of the CLSM consisting of sand, silt, water, flyash, and CSA cement, uniaxial compression test and flow test were carried out. For the measurement of compressional waves, a cell and a couple of transducers were used. The test results show that the compressive strength increases with the curing time, while the increment of compressive strength decreases with the curing time. In addition, the compressive wave velocity increases with the curing time, and the correlation between the compressive wave velocity and compressive strength is similar to exponential function. This study suggests that the correlation between the compressive wave velocity and compressive strength may be effectively used for the estimation of compressive strength of the CLSM at early curing time.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.217-222
• /
• 2000

A large Pc structure building is system that consisted of bearing wall and slab joint. It has general structure stability from unity thar each members tied at joint. The strength of mortar that packing in joint among panels is important to internal force in entire building system. Do, if we could get early strength estimation with microwave. It would bring good construction planning, reduce construction time, and judge building stability and so on. The purpose of this study is to develop early estimation method for making better quality control and constructing good PC panel structure. The results of this study were as follows :1) With sealed molds, reduced moisture volatilization to more than 60% and enlarged 30% accelerated compressive strength than before one. 2) To get more accelerated strength, we should control maximum temperature difference to $30^{\circ}C$ downward 3)Interrelation with 7-day and 28-day strength were 0.831,0.902, and it is above than before one

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.834-837
• /
• 2004

In this study, the electric accelerated reinforcing bar corrosion test was carried out to estimate the coefficient of electrolytic corrosion based on the concept of Faraday's law according to rebar corrosion rate and concrete compressive strength which had an effect on the actual corrosion mass loss. The results of this paper allow the prediction of corrosion amount in the electric accelerated reinforcing bar corrosion test method.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1126-1133
• /
• 1994

When designing an internal gear. the bending strength around pitch point as well as that at tooth root fillet should be considered because the bending stress around pitch point may occur as high as that at tooth root fillet. In this study, including stress state around pitch point, the bending strength (tensile side and compressive side) of internal gear tooth is investigated by the use of the finite element method(FEM) with regarding many influencing factors of cutter and gear geometries. Then, the critical sections around pitch point and at tooth root fillet are determined, and the simple formulae based on nominal stresses(bending, compressive, and shear) are derived for the calculations of actual stresses as the functions of tooth thicknesses and radii of curvatures of involute and fillet curve at those critical sections. The stresses calculated by the formulae agree well with those by the FEM. And the bending stresses around pitch point and at tooth root are easily estimated by the use of those formulae, therefore, those formulae are useful for the purpose of the design or the bending strength estimation of internal gear.