• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.6
• /
• pp.1075-1082
• /
• 2016

In order to calculate the optimum installation interval between a speed hump and hump type crosswalk that are installed continuously in succession, this study examined the speed of a vehicle that passes different intervals between speed humps and hump type crosswalks from the approach section of a roundabout having a maximum speed limit of 30km/h; analyzed the effects of speed humps and hump type crosswalks installed continuously in succession on vehicle driving speed; and simulated the optimum installation height of hump type crosswalk. As a result, the following conclusion was drawn. First, it was found that the optimum interval between a speed hump and hump type crosswalk, which are the representative traffic calming techniques for reducing vehicle speed, to control vehicle speed under 30km/h is 30m. Second, as a result of comparing the deceleration of a vehicle that pass hump type crosswalks, it was found that if the installation interval is 65 m and above, a speed hump and hump type crosswalk had no effect. Therefore, it is desirable that the maximum installation interval between a speed hump and hump type crosswalk for controlling vehicle speed within a fixed road section should not exceed 65m. Third, the analysis showed that the optimum installation height of hump type crosswalk is 6-8cm in case vehicle speed at the approach section is 20km/h or lower, 8-10cm in case of 30km/h, and 10cm in case of 30km/h or higher, respectively. Fourth, even at a road section on which a speed hump and hump type crosswalk are installed, speed reduction effects may sometimes be insignificant due to a driver's studying effect, traffic conditions and so on. Thus, it is judged that speed reduction effects will be greater if several traffic calming techniques such as speed hump, chicane, and choker are applied at the same time. Therefore, in case of applying traffic calming techniques for the purpose of reducing vehicle speed in order to promote pedestrian safety, the composite application of several techniques should be considered.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.36 no.1
• /
• pp.119-125
• /
• 2009

Fusion and gemination are irregularities in tooth development. It is often difficult to differentiate between gemination and fusion and it is common to refer to these anomalies as 'double teeth'. The deciduous teeth are most commonly involved, but in 0.1% of cases permanent teeth are affected, in which case aesthetic, funtional and periodontal problems can result. Double teeth present great difficulties in management and required a multidisciplinary approach. The central groove on the labial and palatal surfaces of a double tooth is extremely prone to caries, therefore early 'fissure sealing' is essential. In permanent dentition, surgical separation of fused teeth may be possible with subsequent orthodontic alignment and restorative treatment as needed to reshape the crown. Reshaping or reduction of a double tooth with a single canal may be attempted by modifying the appearance of the labial groove and the use of composite tints but is often impossible and extraction may be the only alternative. Orthodontic treatment and prosthetic replacement is then required. Implants may be an option for adolescents. The present study describes three clinical cases of double teeth in the position of the maxillary permanent incisors. The first case demonstrates an example of multidisciplinary care including surgical intraoral hemisection, root canal therapy, restorative and orthodontic treatment. The second and third cases describe the external and internal morphology of the two fused teeth by means of three dimensional dental computer tomography.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.2
• /
• pp.14-34
• /
• 1985

One of the techniques for altering the properties of wood that has received considerable attention in the last twenty years is the formation of a wood-polymer composite (WPC) by irradiation and heat-catalyst polymerization of a monomer incorporated into the wood matrix. Wood-polymer composites are the new products having the superior mechanical and physical properties and the combinated characteristics of wood and plastic. The purpose of this experiment was to obtain the basic data for the improvement of wooden materials by manufacturing WPC and Staypak. The species examined was Hyunsasi-Namoo (Populus alba ${\times}$ P. glandulosa) which had not been utilized yet. Methylmethacrylate (MMA) as monomer, benzoyl peroxide (BPO) as initiator and methyl alcohol as bulking agent were used. The monomer containing BPO was impregnated into wood pieces by the dipping and the vacuum process for 2 hours. After impregnation, the treated samples were polymerized on the hot press with pressure and heat-catalyst methods. The results obtained were summarized as follows 1. The monomer loading into wood by the dipping process was 12.13 percent and 29.99 percent by the vacuum. The polymer loading into wood by the dipping process was 6.79 percent and 15.44 percent by the vacuum. 2. Comparing with Staypak, antishrink efficiency (ASE) of WPC was 12.5 to 13.6 percent on the radial direction and 14.70 to 18.63 percent on the tangential. Antiswelling efficiency (AE) was 14.40 to 17.22 percent on the radial direction and 17.18 to 42.1 8 to 42.14 percent on the tangential. Reduction in water absorptivity (RWA) was 8.19 to 15.5 percent. As a whole, the vacuum process was better than the dipping. 3. The specific gravity of control, Staypak and WPC were 0.44, 0.66 and 0.61 to 0.62, respectively. 4. In the bending strength test, the strength in case that the load direction is on the radial surface was greater than that which the load direction is on the tangential. 5. Increasing rate of stress at proportional limit in compression perpendicular to grain was 72.26 percent in case of WPC by the dipping process, 78.93 percent by the vacuum and 99.09 percent in case of Staypak.

• Journal of the Korea Concrete Institute
• /
• v.26 no.4
• /
• pp.441-448
• /
• 2014

From several researches, recently, it was found that using hollowed precast concrete (HPC) column made more compact concrete casting in joint region possible than using normal solid PC (Precast concrete) column. Therefore, the rigidity of joints can be improved like those of monolithic reinforced concrete (RC). After filling the hollow with grout concrete, however, it is expected that the HPC column behaviors like composite structure since PC element and grout concrete have different materials as well as there is a contact surface between two elements. These may affect the structural behavior and strength of the composite column. A compressive strength test was performed for the HPC column with parameter of hollow ratio for the case with and without grout in the hollow and the result is presented in this paper. The hollow ratios in the test are 35, 50 and 59% of whole section of column. Concentrated axial force was applied to top of the specimens supported as pin connection for both ends. In addition, finite element (FE) analysis was performed to simulate the failure behavior of HPC column for axial compression. As a result, it was found that the hollow ratio did not affect the initial stiffness of HPC filled with grout regardless of the strength difference of HPC and grout. However the strength was increased inversely corresponding to the hollow ratio. The structural capacity of HPC without grout closely related to the hollow size. Especially, the local collapse governs the overall failure when the thickness of HPC is too thin. Based on these effect, a suitable equation was suggested for calculation of the compressive strength of HPC column with or without grout. FE analysis considering the contact surface between HPC and grout produced a good result matched to the test result.

• Journal of Life Science
• /
• v.28 no.5
• /
• pp.577-586
• /
• 2018

We recently reported the potential probiotic properties of Lactobacillus brevis SBB07 isolated from blueberries. The present study investigates the effect of culture conditions such as temperature, initial pH, culture time, and medium constituent for industrial application. The ingredients of the medium to improve cell growth were selected by Plackett-Burman design (PBD) and central composite design (CCD) within a desirable range. The PBD was applied with 19 factors: seven carbon sources, six nitrogen sources, and six microelements. Protease peptone, corn steep powder (CSP), and yeast extract were found to be significant factors for the growth of SBB07. The CCD was then applied with three variables found from the PBD at five levels, and the optimum values were decided for the three variables: protease peptone, CSP, and yeast extract. In the case of the growth of SBB07, the proposed optimal media contained 2.0% protease peptone, 2.5% CSP, and 2.0% yeast extract, and the maximum dried-cell weight was predicted to be 2.93963 g/l. By the model verification, it was confirmed that the predicted and actual results are similar. Finally, the study investigated the effects of incubation temperature and initial pH at the optimized medium. It was confirmed that the dried-cell weight increased from $2.2933{\pm}0.0601g/l$ to $3.85{\pm}0.0265g/l$ when compared to the basal medium at $37^{\circ}C$ and initial pH 8.0. Establishing the optimal culture condition for SBB07 provides good potential for applications in probiotics and can serve as the foundation for the industrialization of materials.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.33 no.2
• /
• pp.165-172
• /
• 2006

A direct pulp capping with different medicaments has been attempted for a long time. The most commonly used among those is the calcium hydroxide. In primary teeth, however, a success rate of direct pulp capping with calcium hydroxide has been reported to be lower than that of pulpotomy. The disappointing results of calcium hydroxide have prompted the search for other capping materials. Lately, several researchers suggested an application of adhesive resin-based composite systems as a capping material. They claimed that when an exposed vital pulp is capped directly with bonding resin, the pulp tissue is free of inflammation or necrosis without clinical symptoms. The aim of this study was to compare short-term effects of the bonding resin which was applied on the mechanically exposed vital pulp tissue and those of direct pulp capping with calcium hydroxide. The second objective was to compare success rates of the primary teeth which already underwent physiologic root resorption and those of the teeth which had not undergone physiologic root resorption yet, in each capping material groups. The vital, healthy pulp of forty-one primary teeth were exposed mechanically during a cavity preparation. They were divided into two groups: Group 1(n=21) underwent capping with bonding resin, and group 2(n=20) underwent capping with calcium hydroxide. Then these two groups were subdivided into two groups in each : the teeth which show physiologic root resorption and the teeth without root resorption. All of the sample teeth were restored with composite resin. Clinical evaluations such as percussion test, ice test, EPT, were recorded and also before- and after- standard x-ray films were compared and evaluated to decide whether the case was successful or not. Evaluation was performed at least 3 months after the capping materials. The results were as follows 1. There was no difference in success rate between group 1 and group 2. 2. Success rate of the teeth with physiologic root resorption was higher than that of the teeth without physiologic root resorption in group 1 and group 2. 3. There was no difference in success rate between anterior teeth and posterior teeth.

• Korea Science and Art Forum
• /
• v.37 no.1
• /
• pp.249-260
• /
• 2019

Recently, the proportion of single-person households is on the increase in Korea, expected to reach 34.6% in 2035. Among the single-person households, Young single family households are facing greater difficulties due to high house prices in Korea. The government is expanding its support to Young single family, executing various policies such as public lease housings, private lease housings for youth, youth dormitory, etc. The purpose of this study is to understand the exact housing requirement of Young single family households who have different lifestyles with other age groups and provide base line data for youth house planning which will be in use later on. Study methods are shown below. First, this research studied the status and characteristics of Young single family households by looking into literature. Second, by studying previous studies concerned with life style and housing preferences of youth, the tool for investigating preferences and needs of housing environment by Young single family households was composed. Third, survey on characterstics of space usage, preferences and needs on flat composition, and preferences of interior design were conducted based on lifestyle of Young single family-households. The survey was conducted as an online survey using SNS for 150 Young single family holds from the age of 20 and 39, including students and office workers from December 2018 to January 2019. The results are as following. (1) Looking into the space usage characteristics, considering that various activities other than basic functions take place in bedroom and living room of small-sized Young single family households, we need to consider this additionally when planning the housing. (2) Looking into the preferences and composite needs of flat composition, the subjects demand separate bed room and more living room space, and also demand expansion of living room space where various activities take place and additional storage such as dress room in bed room (3) The preferences toward interior design show preferences toward modern style and achromatic color, a representative color. The subjects also prefer floor finishing materials normally used for living spaces, and indirect, soft lighting that uses wall. Also, there are differences between interior design preferences between students (20's) and office workers(30's) due to their different lifestyles. Research is needed to propose practical residential environment requirements and plans through a case study of actual public rental housing and a wider range of users.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.17 no.2
• /
• pp.247-264
• /
• 1993

This study deals with the manufacturing of the foundation garments for the well-balanced somatotype of the Korean middle-aged womenhood. In order to get hold of the different somatotypes, a survey of a total of 134 middle-aged women in Kwangju area, ranging in their age from 45 through 59 was made. The statistical methods used for the analysis of the basic data were the Pearson's correlation coefficient, Anova, Cluster analysis and Stepwise. Emphasis of the try-on test was placed on (1) the comparison of anthropometric data before and after trying on the foundation garments, (2) sensory evaluation, (3) a rating on fit and performance, (4) the comparison by means of photograph. The conclusions obtained are as follows : 1) The 134 women sampled and measured were classified into the five groups of somatotype : the 52 women (34%) belong to Cluster 1 ; the 22 women(14.5%) belong in Cluster 2 ; the 12 women(7.9%) belong in Cluster 3 ; the 15 women(9.9%) belong in Cluster 4 ; the 33 women(27.7%) belong to Cluster 5. 2) As for the characteristics of the foundation garment design, the V-shaped neckline and chest dart was used. The adjust point is right above the perineum point. The foundation garment length is as far as trochanteric point. The materials used are cotton/polyurethane, lace, 100%cotton. The materials used for corrections were the sponge pad for the chest, and non-woven fabric pad for the back, shoulder and the hip. 3) The comparison of the anthropometric data of the subject when dressed in foundation garments showed a significant difference in bust point height, in bust point length and in nipple-ta-nipple breadth, which proves the foundation garments to be effective in correcting such part as the chest, the hip and the abdomen. 4) As considered in terms of the sensory evaluation, the item except for the shoulder and the armhole coincided with each other in the mean value and in the composite reliability coefficient, which also proves the foundation garments to be effective. 5) Subjects were satisfactory on fit, performance, design, of the foundation garment, and their changed appearance. 6) In the case of the comparison through the photographs, the silhouettes of all the five women subjects were found effectively to be balanced.

• Polymer(Korea)
• /
• v.39 no.3
• /
• pp.433-440
• /
• 2015

Aluminum trihydroxide (ATH) has been commonly employed as a flame retardant for ethylene vinyl acetate (EVA) copolymers. In the present work, ATH was obtained from a recycling process of multi-layer packaging film wastes. EVA/ATH composite samples were prepared using a two roll-mill and flame retardancy of EVA/ATH composites were examined using limiting oxygen index (LOI) and flame retardancy test (UL94). We observed excellent flame retardancy in case of adding 150 phr or more of recycled ATH to EVA. Particle size and specific surface area play crucial roles in LOI value and UL-94 classification of the EVA/ATH composites. Smaller particle size and higher specific surface area of ATH was found out to improve the flame retardancy. Regarding tensile properties, crosslinked EVA/ATH compounds which is practically used for electric cables had similar to or even better tensile property values than the ones without ATH.

• Polymer(Korea)
• /
• v.36 no.6
• /
• pp.810-815
• /
• 2012

The cation exchange polymer, poly(styrene sulfonic acid) (PSSA), was coated onto polyamide (PA) thin film composite reverse osmosis (RO) membranes. Then these membranes were investigated for the model foulants, bovine serum albumin (BSA), humic acid (HA), and sodium alginate (SA) to check whether there are some improvement. The contact angle of PSSA coated PA RO membrane showed $58^{\circ}$ from $78^{\circ}$, the value of PA RO membrane, which confirmed successful hydrophilization. As the operating pressure increased (2, 4, 8 atm for BSA, HA and SA 100 ppm in feed solution), the fouling phenomena was worse for both none- and PSSA-coated membranes. The fouling increased in the order of BSA>SA>HA due to the interactions between sulfonic acid in PSSA and functional groups of foulants. On the other hand more significant fouling reduction was observed in the order of HA>SA>BSA. The photographs of scanning electron microscopy showed the same trend. As a result, there was the improvement of fouling phenomena for the PSSA coated RO membranes, distinctly in the case of HA.