• 한국항공우주학회지
• /
• 제41권8호
• /
• pp.625-631
• /
• 2013

핀풀러의 신뢰도를 몬테카를로 시뮬레이션을 통해서 예측하였다. 예측방법은 응력-강도 간섭 모델에 근거한다. 이 모델은 강도가 응력보다 작을 경우를 고장으로 간주한다. 본 연구에서 강도는 핀을 예정된 거리까지 후퇴시키는데 필요한 에너지로, 응력은 이 핀의 운동을 방해하는데 소요되는 에너지로 간주하였다. 전자는 주로 화약량에 의해 결정되고 후자는 여러 가지 마찰력과 반발방지장치에서 소모되는 에너지에 의존한다. 응력과 강도 변수들은 해석적 성능 모델로부터 계산하였다. 본 연구에서 제시된 방법은 많은 시료가 필요하지 않기 때문에 유사한 종류의 파이로 장치 신뢰도 계산에도 적용될 수 있다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권5호
• /
• pp.645-652
• /
• 2010

본 연구의 목적은 다양한 분위기 압력 하에서 커먼레일 디젤인젝터를 통해 분사되는 비증발 디젤 분무특성에 관한 연구이다. 디젤분무의 거시적 특성으로 분무관통거리와 분무각을 음영사진과 이미지프로세싱으로 연구하였다. 수치해석은 상용 CFD프로그램인 AVL-FIRE를 사용하였다. 분열모델은 WAVE모델을 사용하였으며 표준 $k-{\varepsilon}$난류모델을 적용하였다. 분무각과 Zeuch법을 적용한 연료 분사율을 수치해석의 입력값으로 사용하였다. 분무관통거리를 실험값과 비교하여 좋은 결과를 얻었고 수치해석을 통하여 노즐팁 하류방향으로 분무의 각 구간별 액적입경분포를 알아보았다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.721-724
• /
• 2011

터보펌프에서 발생 가능한 cavitation을 동반하지 않으면서 추진제를 요구하는 압력과 유량으로 연소기에 공급하기 위해서는 추진제 탱크에 저장된 추진제를 가압하는 시스템이 필요하다. 가압시스템은 선가압과 주가압으로 분류할 수 있으며, 본 연구에서는 주가압 시스템에 대해서만 언급한다. 추진제탱크 가압 방식에는 가압가스 생성방법과 공급 방법으로 나눌 수 있으며, 가압가스 생성방법으로는 비활성가스 및 극저온 산화제를 기화시켜 추진제탱크에 공급하는 방법이 있다. 본 연구에서는 가압시스템의 분류와 가압 방식에 따른 장단점을 비교하였으며, 특히 발사체에서 사용하고 있는 가압방식 중에서 임펄스 제어방식의 원리와 가압시스템의 특성을 기술한다. 또한 가압시스템의 구성요소인 열교환기의 형상과 구조 및 각 열교환기의 특징에 대하여 설명한다. 본 자료는 발사체 개발단계에서 가압시스템의 기본요구조건 도출과 개념설계 단계에서 활용할 수 있다.

• 한국대기환경학회지
• /
• 제31권4호
• /
• pp.368-377
• /
• 2015

Bunker C fuel oil is a high-viscosity oil obtained from petroleum distillation as a residue. The sulfur content of bunker C fuel oil is limited to 4.0% or even lower to protect the environment. Because bunker C fuel oil is burned in a furnace or boiler for the generation of heat or used in an engine for the generation of power, carbon dioxide is emitted as a result of combustion. The objective of this study is to investigate $CO_2$ emission characteristics of bunker C fuel oil by sulfur contents. Calorific values and carbon contents of the fuels were measured using the oxygen bomb calorimeter method and the CHN elemental analysis method, respectively. Sulfur and hydrogen contents, which were used to calculate the net calorific value, were also measured and then net calorific values and $CO_2$ emission factors were determined. The results showed that hydrogen content increases and carbon content decreases by reducing sulfur contents for bunker C fuel oil with sulfur contents less than 1.0%. For sulfur contents between 1.0% and 4.0%, carbon content increases as sulfur content decreases but there is no evident variation in hydrogen content. Net calorific value increases by reducing sulfur contents. $CO_2$ emission factor, which is calculated by dividing carbon content by net calorific value, decreases as sulfur content decreases for bunker C fuel oil with sulfur contents less than 1.0% but it showed relatively constant values for sulfur contents between 1.0% and 4.0%.

• 한국응용과학기술학회지
• /
• 제23권1호
• /
• pp.77-84
• /
• 2006

Modified polyesters (TTBA-10C, -20C, -30C) that contain phosphorus and chlorine were synthesized by the condensation polymerization of tetramethylene bis(orthophosphate), neohexanediol trichlorobenzoate, 1,4-butanediol and adipic acid, in which tetramethylene bis(orthophosphate) and neohexanediol trichlorobenzoate were prepared previously in our laboratory. In this study, two-component flame-retardant polyurethane coatings (TTBA-10C/HDI-trimer=TTHD-10C, TTBA-20C/ HDI-trimer= TTHD-20C, TTBA-30C/HDI-trimer= TTHD-30C) were obtained by curing at room temperature with the synthesized TTBAs and hexamethylene diisocyanate (HDI)-trimer as a curing agent. The obtained TTHDs were made into coating samples and used as test samples for various physical properties. The physical properties of the flame-retardant coatings containing chlorine and phosphorus groups were generally inferior to those containing only phosphorus group. Flame retardancy was tested by vertical and horizontal combustion method, and $45_{\circ}$ Meckel burner method. Since the retardancy of flame-retardant coatings containing chlorine and phosphorus groups was better than that containing only phosphorus group, it could be concluded that the retardancy by the synergism effect of chlorine and phosphorus groups exhibited.

• 대한기계학회논문집B
• /
• 제28권12호
• /
• pp.1557-1566
• /
• 2004

A flame extinction phenomenon is a typical unsteady process in combustion. Flame extinction is characterized by various physical phenomena, such as convection, diffusion, and the production of heat and mass. Flame extinction can be achieved by either increasing the strain rate or curvature, by diluting an inert gas or inhibitor, or by increasing the thermal or radiant energy loss. Though the extinction is an inherently transient process, steady and quasi-steady approaches have been used as useful tools for understanding the flame extinction phenomenon. Recently, unsteady characteristics of flames have been studied by many researchers, and various attempts have been made to understand unsteady flame behavior, by using various extinction processes. Representative parameters for describing flame, such as flame temperature, important species related to reactions, and chemi-luminescence of the flame have been used as criterions of flame extinction. In these works, verification of each parameter and establishing the proper criterions of the extinction has been very important. In this study, a time-dependent flame temperature and an OH radical concentration were measured using optical methods, and the instantaneous change of the flame luminosity was also measured using a high-speed ICCD (HICCD) camera. We compare the unsteady extinction points obtained by three different methods, and we discuss transient characteristics of maximum flame temperature and OH radical distribution near the extinction limit.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.156-165
• /
• 2014

This paper is the first investigation on the effect of flow control methods on the part load performance in a spark ignition engine. For comparison of the methods, two control devices, port throttling and masking, were applied to a conventional engine without any design change of the intake port. Steady flow evaluation shows that steady flow rates per unit opening area and swirl ratio are very low compared with the port throttling and saturated from mid-stage valve lift, however, swirl increases slightly as the lift is higher in case of 1/4 masking control. In the part load performance, the effect of simple port throttling on lean misfire limit expansion is limited and insufficient; on the other hand a masking improves the limit considerably without any port modification for increasing swirl. Also the results show that the intake flow control improves the combustion with following two mechanisms: stratification induced by the combination of the flow pattern and the fuel injection timing attribute to ignition ability and the intensified flow ensure fast burn. In addition fuel consumption reduces under the flow controls and the reduction rate is different according to the operation conditions and control methods. At the Stoichiometric and/or low speed and low load the throttling method is more advantageous; however vice versa at lean and high load condition. Finally, the throttling is more efficient for HC reduction than masking, on the other side the NOx emissions increase under the masking and decrease under the port throttling compared with conventional port scheme.

• Journal of Biosystems Engineering
• /
• 제42권1호
• /
• pp.44-55
• /
• 2017

Background: Heat recovery is one of the prominent ways to save a considerable amount of conventional fossil fuel and minimize its adverse effects on the environment. The rotary heat exchanger is one of the most effective and efficient devices for heat recovery or heat exchanging purposes. It is a regenerative type of heat exchanger, which has been studied and used for many heat recovery purposes. However, regenerative thermal wheels have been mostly used as heat recovery systems in buildings. For modeling a rotary regenerator, it is very important to numerically consider all the factors involved, such as effectiveness, rotational speed, geometrical size and shape, and pressure drop (${\Delta}p$). In recent times, several researchers have actively studied the rotary heat exchangers, both theoretically and experimentally. Reviews: In this paper different advances in the numerical modeling of regenerative rotary heat exchangers in relation to fluid flow and heat transfer have been discussed. Researchers have indicated that the effectiveness of the regenerative rotary heat exchanger depends on various factors including, among many others, rotational speed, rotational period and combustion power. It is reported that with the increase of periodic rotation the deviation of theoretical results from the experimental result increases. The available literature indicates that regenerative heat exchangers are having relatively more effectiveness (60-80%), compared to other heat exchangers. It is also observed that the finite difference method and finite volume methods are mostly used for discretizing the heat transfer governing equations, under some assumptions. Research also indicates that for the effectiveness calculation the ${\varepsilon}-NTU$ method is the most popular and convenient.

• 화약ㆍ발파
• /
• 제37권4호
• /
• pp.10-16
• /
• 2019

충격파나 압력파가 구조물에 미치는 영향을 평가하기 위해서는 과압, 양의 압력 지속시간, 충격량에 대한 정보가 필요하다. 본 연구에서는 증기운 폭발 해석에 효과적인 다중에너지법을 적용하여 과압 및 양의 압력 지속 시간을 결정하였다. 영국 Nypro 화학회사에서 발생한 싸이클로헥산 증기운 폭발 사고에서 추정된 총 폭발열을 기반으로 폭발원으로부터 40, 80, 120, 160, 200, 240, 280, 320, 360(m) 이격된 지점에서의 과압, 양의 압력 지속시간을 평가하였다. 거리에 따라 과압은 지수적으로 감소하는 것으로 나타났고, 양의 압력 지속시간은 거의 선형적으로 증가하는 것으로 나타났다. 상기의 각 거리에서 구한 과압 및 충격량을 이용하여 각 거리에서의 구조물의 손상 확률을 평가하기 위해서 프로빗 함수를 사용하였다. 손상 확률을 평가한 결과 120m 이내 지점에서는 붕괴의 가능성이 크고, 240m 이내에서는 심각한 구조물의 손상이, 구조물의 가벼운 손상과 유리창 파손은 전 범위에 걸쳐서 발생하는 것으로 나타났다.

• Tribology and Lubricants
• /
• 제33권2호
• /
• pp.45-51
• /
• 2017

Engine oil is a substance used for the lubrication of internal combustion systems. However, in some case, defects in engine systems may contaminate engine oil with fuel. Contaminated engine oil can cause problems in the normal functioning of a vehicle. In this study, we investigate the functional properties of engine oil contaminated with diesel fuel. The test results indicate that the engine oil contaminated with diesel fuel has low flash point, pour point, density, kinematic viscosity and cold cranking simulator value. The contaminated engine oil which has low plash point can cause fire and explosion accident. Furthermore, a four ball test indicates that the contaminated engine oil increases wear scar to poor lubricity. Moreover, we investigate the GC pattern using SIMDIST (simulated distillation) for determination of diesel in engine oil. The SIMDIST analytic result, diesel was detected at earlier retention time than engine oil in chromatogram. Thus the SIMDIST method can define whether engine oil is contaminated by diesel fuel or not. We can use the SIMDIST method for the diagnosis of oil condition instead of analyzing other physical properties that require many analytic instruments, large volume of oil sample and long analysis time.