• 한국자동차공학회논문집
• /
• 제18권3호
• /
• pp.26-36
• /
• 2010

This paper provides a description of the combustion model to obtain an accurate dynamic engine phenomena that satisfies real-time simulation for model-based engine control. The combustion chamber is modeled as a storage device for mass and energy. The combustion process is modeled in terms of a two-zone model for the burned and unburned gas fractions. The mass fraction burnt is modeled in terms of a Wiebe function. The instantaneous net engine torque is calculated from the engine speed and the instantaneous piston work. The modeling accuracy has been tested with a cylinder pressure data on a test bench and also the ability of real-time simulation has been checked. The results show that combustion model yields sufficiently good performance for the model-based control logic design. However the influence factors effected on model accuracy are some room for improvement.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 춘계학술대회 논문집
• /
• pp.128-132
• /
• 2009

2차 연료 분사장치를 이용한 연구용 연소기의 연소불안정 능동 제어장치를 설계하였다. Cambridge Combustor 모델을 이용하여 제어 가능함을 보였고, 적용한 적응제어 알고리즘에 대한 제어장치의 요구조건을 도출하였다. 적응제어 법칙을 구현하기 위하여 주파수 추정기가 가져야 할 성능과 연료제어 밸브의 주파수 대역에 대하여 제어장치를 이용하여 실험적으로 검증하였다. 시험 결과 대역폭 150Hz 이하의 연소 불안정 모드에 대하여 귀환제어 방식의 연소불안정 능동제어기로 사용 가능함을 보였다.

• 로봇학회논문지
• /
• 제17권1호
• /
• pp.93-101
• /
• 2022

Bioheavy oil, which is expanding its range of use as an alternative fuel to reduce environmental pollutant emissions, has a lot of difficulty in combustion due to its low emission of pollutants such as nitrogen oxide (NOx) and sulfur oxide (SOx), while its low dissipation and high oxygen content in fuel. many studies have been conducted on change in characteristics by mixing rate combustion characteristics and combustion reactions, but there have been no specific and effective studies on the composition of control system, optimization of control, development of logic for mixing and burning, minimizing environmental pollutantants discharge. In this study, we intend to consider systemmatic and empirical considerations on the composition, logic development, solve the problem of manual switching of bioler master due to excessive oxygen content and tuning of the control system for optimal combustion of bioheavy oil.

• 한국연소학회:학술대회논문집
• /
• 대한연소학회 2003년도 제27회 KOSCO SYMPOSIUM 논문집
• /
• pp.299-308
• /
• 2003

This paper provides a review of the status and of the perspectives of advanced catalytic combustion for ultra clean combustion of gas turbines and for industrial combustors. The development of catalytic materials and their combustion techniques for gas turbines are briefly reported. The fuel-rich approaches to catalytic combustion are mentioned for a new technology of thermal- and fuel-NOx control. The fuel-rich catalytic combustion are also applicable to the combustor of ceramic gas turbine, and to the combustion of biomess and municipal waste sludge. Some extended technologies of combustion synthesis are introduced for the synthesis of carbon nanotube and of Perovskite combustion catalysts

• 한국대기환경학회지
• /
• 제33권5호
• /
• pp.473-479
• /
• 2017

This study was designed to understand characteristics of oxy-combustion of coal, dried sewage sludge and solid refuse fuel (SRF). Thermogravimetric analysis was conducted by burning the fuels with air, 21% oxygen ($O_2$)/79% carbon dioxide ($CO_2$) and 30% $O_2/70%$ $CO_2$. Heating rates were varied as 5, 10, 25, 40 and $100^{\circ}C/min$. Complete coal combustion was found at the heating rates of 5, 10, 25 and $40^{\circ}C/min$, and different combustion behavior was found with the gas composition at the heating rates of 10, 25, 40 and $100^{\circ}C/min$. Coal combustion with 30% $O_2/70%$ $CO_2$ showed the highest while coal combustion with 21% $O_2/79%$ $CO_2$ showed the lowest combustion rate. On the other hand, the combustion of dried sewage sludge and SRF showed similar combustion behavior with respect to the combustion gas composition. This suggests that oxy-combustion of dried sewage sludge and SRF which contain a large amount of volatile matter may show similar combustion behavior to their air combustion.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권6호
• /
• pp.1298-1307
• /
• 2001

Recently, the efforts to improve fuel economy and to reduce pollutant emission have become the main subject in the development of a gasoline engine. A lean combustion engine admitted as the best alternative is relatively lower fuel consumption rate and exhaust emissions. In this study, it is focused on intensifying intake flow field as one of methods to improve the performance of the lean combustion. First, three different types of suitable swirl control valve(SC7) with high swirl and tumble ratio are selected through steady flow experiment, being installed in a spark ignition engine. The relationship between lean misfire limit and torque was investigated with injection timing and spark ignition timing. Also, the effect of intensified swirl new on the combustion Stability and exhaust emissions was experimently examined by the measuring in-cylinder pressure and combustion variation. The results show that the engine with swirl control calve is superior to other conventional engine on the lean misfire limit, specific torque, combustion variation and emission, and the appropriate injection timing and spark ignition timing exist according to the type of swirl control valve.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 2002년도 추계 학술발표회 논문집
• /
• pp.133-140
• /
• 2002

Catalytic combustion known as one of the traditional oxidation methods of VOC gas is restricted to its applicable fields because of its reaction characteristics. But recently innovative improvement of catalytic endurance makes its applicable range broader from MEMs to industrial power generation. Therefore, control technologies based on the catalytic combustion characteristics are researched and developed dynamically. Especially, the stable control of catalytic combustion is an essential factor in a view of maximizing its efficiency. In this research, the fuel equivalence ratio and the preheating temperature of mixture gas is controlled by catalytic combustion system enhanced in heat transfer with high temperature heat exchanger. As a result the combustion characteristics of system was investigated, and both passive and active control type were compared and analyzed.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.1190-1195
• /
• 2005

Biomass burning is a source of greenhouse gases, carbon dioxide, methane, and nitrous oxide. Under the ideal conditions of complete combustion, the burning of biomass produces carbon dioxide and water vapor. Since complete combustion is not achieved under any conditions of biomass burning, other carbon species, including carbon monoxide, methane, non-methane hydrocarbons and particulate carbon are produced. In this study, we analyze the combustion characteristics of rice-husk, such as heat release rate, smoke production rate, the percentage variation of CO and $CO_2$, oxygen consumption rate, and mass loss under different heat fluxes (20, 50 and 70kW). As a result, at 20kW incomplete combustion is occurred so that the percentage of CO is high in initial burning and total smoke release is higher than the others. At 50kW and 70kW, the combustion behaviors is very similar except the variation of CO percentage.

• 한국가스학회지
• /
• 제21권1호
• /
• pp.52-58
• /
• 2017

2015 국민안전처 통계에 따르면, 화재 피해 중 연소생성물에 의한 피해가 가장 많은 사상자를 내는 것으로 나타났다. 이러한 이유로 최근 연소생성물에 관한 연구는 국내외에서 활발하게 이루어지고 있다. 국내에서는 연소 생성물이 사람에게 미치는 영향과, 화염의 전파속도에 미치는 영향이라는 관점에서 연구가 진행되고 있고, 해외에서는 연소생성물이 사람에게 미치는 독성 뿐만 아니라 offshore 대피소에 미치는 영향까지 연구되고 있다. 연소생성물은 독성을 가지고 있고, 시야를 가려 탈출을 방해하기 때문에 많은 연구에서 실험과 CFD시뮬레이션을 이용하여 연소 생성물 제거 설비의 최적화에 관한 연구를 진행하고 있다. 본 연구에서는 연소를 통한 독성가스 발생 모델과, 그 가스의 제거 시설에 대한 연구 동향을 분석하여, 추후 연소생성물 연구의 기준이 될 것으로 판단된다.

• 한국자동차공학회논문집
• /
• 제14권3호
• /
• pp.178-185
• /
• 2006

This paper investigates the steady-state combustion characteristics of the Homogeneous charge compression ignition(HCCI) engine with variable valve timing(VVT) and dimethyl ether(DME) direct injection, to find out its benefits in exhaust gas emissions. HCCI combustion is an attractive way to lower carbon dioxide($CO_2$), nitrogen oxides(NOx) emission and to allow higher fuel conversion efficiency. However, HCCI engine has inherent problem of narrow operating range at high load due to high in-cylinder peak pressure and consequent noise. To overcome this problem, the control of combustion start and heat release rate is required. It is difficult to control the start of combustion because HCCI combustion phase is closely linked to chemical reaction during a compression stroke. The combination of VVT and DME direct injection was chosen as the most promising strategy to control the HCCI combustion phase in this study. Regular gasoline was injected at intake port as main fuel, while small amount of DME was also injected directly into the cylinder as an ignition promoter for the control of ignition timing. Different intake valve timings were tested for combustion phase control. Regular gasoline was tested for HCCI operation and emission characteristics with various engine conditions. With HCCI operation, ignition delay and rapid burning angle were successfully controlled by the amount of internal EGR that was determined with VVT. For best IMEP and low HC emission, DME should be injected during early compression stroke. IMEP was mainly affected by the DME injection timing, and quantities of fuel DME and gasoline. HC emission was mainly affected by both the amount of gasoline and the DME injection timing. NOx emission was lower than conventional SI engine at gasoline lean region. However, NOx emission was similar to that in the conventional SI engine at gasoline rich region. CO emission was affected by the amount of gasoline and DME.