• Earthquakes and Structures
• /
• v.7 no.5
• /
• pp.779-796
• /
• 2014

This experimental investigation was conducted to examine the behavior and response of high-strength material (HSM) reinforced concrete (RC) columns under combined high-axial and cyclic-increasing lateral loads. All the columns use high-strength concrete ($f_c{^{\prime}}$=100MPa) and high-yield strength steel ($f_y$=685MPa and $f_y$=785MPa) for both longitudinal and transverse reinforcements. A total of four full-scale HSM columns with amount of transverse reinforcement equal to 100% more than that required by earthquake resistant design provisions of ACI-318 were tested. The key differences among those four columns are the spacing and configuration of transverse reinforcements. Two different constant axial loads, i.e. 60% and 30% of column axial load capacity, were combined with cyclically-increasing lateral loads to impose reversed curvatures in the columns. Test results show that columns under 30% of axial load capacity behaved much more ductile and had higher lateral deformational capacity compared to columns under the 60% of axial load capacity. The columns using closer transverse reinforcement spacing have slightly higher ductility than columns with larger spacing.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.11
• /
• pp.1207-1214
• /
• 2014

Under excessive plasticity, the fracture toughness of a material depends on its size and geometry. Under fully yielded conditions, the stresses in a material near its crack tip are not unique but rather depend on the geometry. Therefore, the single-parameter J-approach is limited to a high-constraint crack geometry. The JQ theory has been proposed for establishing the crack geometry constraints. This approach assumes that the crack-tip fields have two degrees of freedom. In this study, the crack-tip stress field of a fully circumferential surface-cracked pipe under combined loads is investigated on the basis of the JQ theory by using finite element analysis. The combined loads are a tensile axial force and the thermal gradient in the radial direction. Q-stresses of the crack geometry and its loading state are used to determine the constraint effects. The constraint effects of secondary loading are found to be greater than those of primary loading. Therefore, thermal shock is believed to be the most severe loading condition of constraint effects.

• Structural Engineering and Mechanics
• /
• v.52 no.6
• /
• pp.1273-1287
• /
• 2014

Plates are most widely used in the hulls of floating concrete structures, bridge decks, walls of off-shore structures and liquid storage tanks. A method of analysis is presented for the determination of load-deflection response and ultimate strength of high-strength steel fiber reinforced concrete (HSSFRC) plates simply supported on all four edges and subjected to combined action of external compressive in-plane and transverse loads. The behavior of HSSFRC plate specimens subjected to combined uniaxial in-plane and transverse loads was investigated. The proposed analytical method is compared to the physical test results, and shows good agreement. To predict the constitutive behavior of HSSFRC in compression, a non-dimensional characteristic equation was proposed and found to give reasonable accuracy.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.7
• /
• pp.1685-1696
• /
• 1994

In this paper, a new forming process of the large-size forgings within the limit of forming loads is developed by introducing the incremental forging method and combined forming method. For the development of the forming process, various related processes are proposed and modelling experiments of plasticine and corresponding numerical simulation ate carried out. Thus, an optimal process considering the productivity and economical efficiency is recommended from the study of formability and forming loads, etc. The selected process is subjected to a modelling experiment of lead and 1/7 scale prototype experiment of the real material so as to verify the effectiveness of a selected process as well as to determine the design parameters. The developed process is then applied the forging product of dome shape. Dome-shaped forgings can be produced by the developed process within the limit loads and with the simple tools.

• Earthquakes and Structures
• /
• v.7 no.5
• /
• pp.719-733
• /
• 2014

The equivalent frame method (EFM) is widely used for the design of two-way reinforced concrete slab structures, and current design codes of practice permit the application of the EFM in analyzing the flat plate slab structures under gravity and lateral loads. The EFM was, however, originally developed for the flat plate structures subjected to gravity load, which is not suitable for lateral loading case. Therefore, this study, the first part of series research paper, proposed the structural analysis method for the flat plate slab structures under the combined gravity and lateral loads, which is named as the unified equivalent frame method (UEFM). In the proposed method, some portion of rotation induced in the torsional member is distributed to the flexibility of the equivalent columns, and the remaining portion is contributed to that of the equivalent slabs. In the consecutive companion paper, the proposed UEFM is verified by comparing with test results of multi-span flat plate structures. Also, a simplified nonlinear push-over analysis method is proposed, and verified by comparing to test results.

• Journal of the Society of Naval Architects of Korea
• /
• v.61 no.1
• /
• pp.44-50
• /
• 2024

In order to reasonably predict damage extents of naval ships under in-compartment explosion (INCEX) loads, two conditions should be fulfilled in terms of accurate INCEX load generation and fracture estimation. This paper seeks to predict damage extents of various naval ships by applying the CONWEP model to generate INCEX loads, combined with the Hosford-Coulomb (HC) and localized necking (LN) fracture model. This study selected a naval ship with a 2,000-ton displacement, using associated specifications collected from references. The CONWEP model that is embedded in a commercial finite element analysis software ABAQUS/Explicit was used for INCEX load generation. The combined HC-LN model was used to simulate fracture initiation and propagation. The permanent failures with some structural fractures occurred where at the locations closest to the explosion source points in case of the near field explosions, while, some significant fractures were observed in way of the interfaces between bulkheads and curtain plates under far field explosion. A large thickness difference would lead to those interface failures. It is expected that the findings of this study enhances the vulnerability design of naval ships, enabling more accurate predictions of damage extents under INCEX loads.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.5 no.4
• /
• pp.109-120
• /
• 2001

Live load data were collected with a systematic manner from a survey of a refrigeration stores. Using the collected floor live load survey data, the basic statistics, a histogram of the uniformly distributed loads, and the equivalent uniformly distributed loads are computed for various structural members. Based on the above results, the maximum values of a combined live loads during the design life have been estimated and compared with current design live loads. The ultimate goals of this study are to develop probabilistic live load models to analyze survey data of domestic refrigeration stores, and to propose design live loads for structural types.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.04b
• /
• pp.85-91
• /
• 2000

The smallest value of the load when the equilibrium condition becomes to be unstable is defined as the buckling load. The primary objective of this paper is to analyse stability boundaries for star dome under combined loads and is to investigate the iteration diagram under the independent loading parameter In numerical procedure of the geometrically nonlinear problems, Arc Length Method and Newton-Raphson iteration method is used to find accurate critical point(bifurcation point and limit point). In this paper independent loading vector is combined as proportional value and star dome was used as numerical analysis model to find stability boundary among load parameters and many other models as multi-star dome and arches were studied. Through this study we can find the type of buckling mode and the value of buckling load.

• Journal of the Korean Society of Safety
• /
• v.29 no.2
• /
• pp.53-61
• /
• 2014

This study evaluated wind loads considering a local basic wind velocity and construction periods to define the level of applied wind loads for system supports. Structural responses of system supports were examined and compared to those of system supports with the level of wind loads following various standards and specifications for permanent and temporary structures. And, the maximum combined stress ratios were estimated to evaluate the structural safety of a considered system support. From results, it was found that the wind load level should be applied in accordance with construction periods when estimating the safety of system supports. Looking into the response by change of the basic wind velocity according to local regions, it is no need to consider wind loads in regions with the basic wind velocity of 30 m/s. However, it was analyzed that wind loads should be considered in the regions with the basic wind velocity of 40 m/s or above. In addition, wind loads should be considered in designing system supports located at the region with the basic wind velocity of 35 m/s starting from construction period of 1.5 years. The standard specification for temporary work was analyzed as an incorrect standard in evaluating wind loads, since it underestimated the response of system supports in accordance with the local basic wind velocity and construction periods.

• Earthquakes and Structures
• /
• v.9 no.2
• /
• pp.415-430
• /
• 2015

Integral abutment bridges have many advantages over bridges with expansion joints in terms of economy and maintenance costs. However, in the design of abutments of integral bridges temperature loads play a crucial role. In addition, seismic loads are readily transferred to the substructure and affect the design of these components significantly. Currently, the European and American bridge design codes consider these two load cases separately in their recommended design load combinations. In this paper, the importance and necessity of combining the thermal and seismic loads is investigated for integral bridges. A 2D finite element combined pile-soil-structure interactive model is used in this evaluation. Nonlinear behavior is assumed for near field soil behind the abutments. The soil around the piles is modeled by nonlinear springs based on p-y curves. The uniform temperature changes occurring at the time of some significant earthquakes around the world are gathered and applied simultaneously with the corresponding earthquake time history ground motions. By comparing the results of these analyses to prescribed AASHTO LRFD load combinations it is observed that pile forces and abutment stresses are affected by this new load combination. This effect is more severe for contraction mode which is caused by negative uniform temperature changes.