• 한국표면공학회지
• /
• 제27권3호
• /
• pp.149-157
• /
• 1994

The formation of spangles on a hot dip galvanized sheet steel by spray cooling the molten zinc coating with air, water and 2.0wt% $NH_4H_2PO_4$ solution has been studied performing laboratory experiments, and their coating properties have been evaluated. Minimized spangles were easily formed by mist spraying the solution for 1 second at the low nozzle spray pressure onto the molten zinc at 420~$422^{\circ}C$ because the solute $NH_4H_2PO_4$ in the sprayed solution imparted a highly rapid cooling effect to the coating through its endothermic de-composition reactions and because the decomposed products acted as numerous nucleation sites for the mini-mized spangles on the coating. Good surface appearances sand sound coating properties were obtained on this coating. Only regular spangles were formed on the coating by the forced convective air cooling. At the high nozzle spray pressure, zero spangles were formed on the coating by the pure water spray cooling. However, the coating had a dull and rough surface with craters sand cracks.

• ALGAE
• /
• 제22권2호
• /
• pp.141-146
• /
• 2007

Seagrass bed is an important component in coastal and estuarine ecosystems, providing food and habitats to a wide variety of marine organisms. Recently, seagrass coverage has declined significantly due to anthropogenic impacts such as cultural eutrophication and reclamation, and thus efforts are under way to prevent further losses and restore disturbed seagrass habitats worldwide. Seagrass transplantation techniques for habitat restoration include vegetative and seed-based methods. Seagrass seeds can be collected easily, and sowing seeds is an economically effective method for large-scale restoration. However, large numbers of seed can be lost by seed predation and physical disturbance in the planting areas. In the present study, Zostera marina seeds were coated with loess to reduce seed loss by predation and sweeping away by the water currents, and germination rates of coated seeds and seedling growth were examined to assess the feasibility of the seed-coating method for large-scale restoration. Germination rate of the coated seeds with loess was significantly higher than that of the uncoated seeds. Additionally, seedling growths were not significantly different between the coated and the uncoated seeds. These results suggest that coating of eelgrass seeds with loess enhances success of seed germintion with no harmful effects on seedling growth. Therefore, the seed coating method using loess may be an effective and applicable seedbased transplanting technique for large-scale restoration.

• 전기학회논문지
• /
• 제60권1호
• /
• pp.85-92
• /
• 2011

Main characteristic in railroad is the guided movement of the wheel by the track through a metal-to-metal contact, conferring to the rail vehicle a single degree of freedom. There are defects such as head check, shelling, corrugation, squats etc in surface of the rail by interface between the wheel and rail. These defects bring about reducing the life-cycle of rails and track components and increasing noises. In case of bad conditions, it is possible to happen to full-scale accident such as derailment. Recently, the track capacity has been increased for increasing speed and operation efficiency. So, maintenance and indirect cost have been increased. Currently, a coating method of rail construction is proposed by using the ceramics in Korea. Rails are used as the earth in electrical railroad systems. Currently traction return current is flowed through wheels of trains. In case of rails coated, problems are caused in the contact power between wheel and coating material of spray. In this paper, electric model is presented in the AT feeding method. In case of rails coated, electric model is presented. Also, standard resistance of the ceramic is demonstrated by contact power between wheel and coating material of spray.

• 한국표면공학회지
• /
• 제50권6호
• /
• pp.523-530
• /
• 2017

In this study, we developed the h-BN interphase for ceramic matrix composites (CMCs) through a wet chemical coating method, which has excellent price competitiveness and is a simple process as a departure from the existing high cost chemical vapor deposition method. The optimum condition for nitriding an h-BN interphase using boric acid and urea as precursors were derived, and the h-BN interphase coating through a wet method on a carbon preform of 2.5 D was conducted to apply the optimum conditions to the CMCs. In order to control the coating property via the wet coating method, four parameters were investigated such as dipping time of the specimen in the precursor solution, the ratio of boric acid and urea in the precursor, the concentration of solution where the precursor was dissolved, and the cycle of dipping and dry process. The CMCs was fabricated through polymer impregnation and pyrolysis (PIP) processes and a three-point flexural strength test was conducted to verify the role of the coated h-BN interphase.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.256-256
• /
• 2013

Carbon nanotubes (CNT) / polyvinylidene fluoride (PVDF) piezoelectric composite films for nanogenerator devices were fabricated by spray coating method. When the CNT/PVDF mixture solution passes through the spray nozzle with small diameter by the compressed nitrogen gas, electric charges are generated in the liquid by a triboelectric effect. Then randomly distributed ${\beta}$ phase PVDF film could be re-oriented by the electric field resulting from the accumulated electrical charges, and might be resulted in extremely one-directionally aligned ${\beta}$ phase PVDF film without additional electric field for poling. X-ray diffraction patterns were used to investigate crystal structure of the CNT/PVDF composite films. It was confirmed that they revealed extremely large portion of the ${\beta}$ phase PVDF crystalline in the film. Therefore we could obtain the poled CNT/PVDF piezoelectric composite films by the spray coating method without additional poling process. Charge accumulation and resulting electric field generation mechanism by spray coating method were shown in Fig. 1. The capacitance of the CNT/PVDF films increased by adding CNTs into the PVDF matrix, and finally saturated. However, the I-V curves didn't show any saturation effect in the CNT concentration range of 0~4 wt%. Therefore we can control the performance of the devices fabricated from the CNT/PVDF composite film by adjusting the current level resulted from the CNT concentration with the uniform capacitance value.

• Tribology and Lubricants
• /
• 제36권6호
• /
• pp.378-384
• /
• 2020

The friction surfaces of mechanical parts are heat-treated or coated with hard materials to minimize wear. Increasing the hardness is a very useful way to reduce abrasive wear. The general Brinell hardness test, which is widely used for metallic materials, is not suitable because it hardly shows any change in hardness when coated with thin films. In this study, we propose a basis for the application of the new Brinell hardness test method to the coated friction surface. An indentation analysis of the rigid sphere and elastic-perfectly plastic materials is performed using a commercial finite element analysis software. The results indicate that their loadto-diameter ratio is the same; the Brinell hardness test method can be applied even when the indenter diameter is on the micrometer scale. In the case of hard coating, it is difficult to calculate Brinell hardness using the diameter of the indentation, but the study revealed, for the first time, that it can be calculated using the depth of the indentation regardless of coating. The change in hardness owing to thin film coating over a wide load range implies that the hardness evaluation method is appropriate. Additional studies on various properties related to the substrate and coating material are required to apply the proposed method.

• 한국세라믹학회지
• /
• 제46권3호
• /
• pp.301-305
• /
• 2009

The novel carbon coating process for interlayer of fiber reinforced ceramic composites between fiber and matrix was performed by carbonizing phenolic resin solution that coated on fiber surface in $N_2$ atmosphere at $600^{\circ}C$ to improve the strength and fracture toughness of CMC(ceramic matrix composite). 160 nm carbon layer was coated on fiber surface with 5 vol% of phenolic resin solution. Since the process temperature ($600^{\circ}C$) is lower than chemical vapor deposition($900{\sim}1000^{\circ}C$), the strength and toughness could be preserved. Furthermore the coating thickness uniformity was improved to 8% of deviation along the stacking sequence. Therefore, prevention from fiber degradation during coating process and controlling coating thickness uniformity along the preform depth were achieved by coating with phenolic resin carbonizing method.

• 항공우주기술
• /
• 제8권1호
• /
• pp.138-143
• /
• 2009

액체로켓엔진 연소기에 적용된 대기 플라즈마 코팅 및 전해/무전해 도금 코팅의 열차폐 효율과 내구성 평가를 수행하였다. 연소시험 결과 대기 플라즈마 방식의 $ZrO_2$, NiCrAlY 코팅은 로켓엔진 연소기의 초음속 유동영역에서 코팅이 표면에서 박리되는 현상이 간헐적으로 발생하였으며 따라서 이러한 문제를 극복할 수 있는 대체 코팅 방식이 요구되었다. 시험 결과 열차폐 효율 및 내구성 관점에서 대기 플라즈마 방식의 $ZrO_2$, NiCrAlY 코팅의 대안으로 무전해/전해 방식을 사용한 니켈-크롬 코팅을 사용할 수 있음을 알 수 있었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제17권4호
• /
• pp.84-90
• /
• 2013

본 논문은 기존 순환골재 생산공장에서 새로운 설비투자나 복잡한 처리공정을 거치지 않고 비교적 용이하게 순환골재의 품질을 개선할 수 있는 효과적인 코팅처리방법을 도출하고, 도출한 코팅처리방법으로 순환골재를 코팅처리하여 그 품질개선 효과를 확인하였다. 연구목적을 달성하기 위하여 순환골재를 코팅하기 위하여 코팅처리용액중 하나인 실리케이트 용액을 경제성 있게 알맞은 농도로 희석하여 사용하였으며, 골재의 코팅방법을 달리하여 12가지 종류의 코팅골재에 대한 물성평가를 실시하였다. 또한 가장 좋은 물성을 나타낸 코팅골재를 사용하여 콘크리트를 제조하였다. 이상의 실험결과 골재를 코팅처리용액에 함침 및 건조를 반복하였을 때 골재의 품질이 가장 우수하게 나타났고, 다른 코팅방법 또한 물성이 코팅처리 전 골재보다는 향상되는 것으로 나타났으나, KS 기준에는 미치는 못하는 결과를 나타내었다. 또한, 가장 좋은 물성을 나타낸 골재를 가지고 콘크리트를 제조한 결과 설계기준강도를 만족시키는 압축강도가 측정되었으며, 설계기준강도 24MPa 이하의 도로시설물을 축조할 때 활용이 가능할 것으로 판단된다.

• 한국결정성장학회지
• /
• 제8권2호
• /
• pp.292-298
• /
• 1998

출발원료로 ferric nitrate, ethylene glycol, acethyl acetone 혼합용액을 사용하여 dip-coating된 ${\alpha}-Fe_2O_3$ 막을 제조하였다. coating을 위한 혼합용액의 시간 경과에 따른 용액내의 가교(polymerization) 효과를 관찰하기 위해서 적외선 분광기(FT-IR)를 사용하였고, 막 형성시 유기물 분해 및 결정화 시작온도를 확인하기 위하여 FT-IR, XRD, DSC 등을 이용하여 분석을 행하였다. 또한 AFM과 SEM을 통하여 각 조건에서 제조된 막의 표면상태 및 두께 변화에 대하여 관찰되었다.