• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.957-967
• /
• 2017

Firing test of the fuel grain for solid fuel ramjet with additives and ignition support material was conducted. Fuel grain consist of HTPB mixed with AP particle 15 wt.%, Boron particle 5 wt.%. To cause the short ignition delay, ignition support consist of $NC/BKNO_3$ and composite propellant was coated to the fuel grain. An oxidant gas having a controlled temperature, pressure and oxygen composition close to the air condition in the ramjet combustor was supplied using the Ethanol blended $H_2O_2$ gas generator. Gas was set to flow at a mass flow rate of 150 g/s and mass flux of $200kg/m^2s$ in the grain port. Through the test, ignition support operated well and ignition delay of 0.5. During the test, stable chamber pressure with 8 bar and high combustion efficiency of 0.86 was confirmed.

• Journal of Powder Materials
• /
• v.17 no.6
• /
• pp.456-463
• /
• 2010

This paper describes the results of the application of Cr-Diamond-like carbon (DLC) films for efficiency improvement through surface modification of spur gear parts in the hydraulic gear pump. Cr-DLC films were successfully deposited on SCM 415 substrates by a hybrid coating process using linear ion source (LIS) and magnetron sputtering method. The characteristics of the films were systematically investigated using FE-SEM, nano-indentation, sliding tester and AFM instrument. The microstructure of Cr-DLC films turned into the dense and fine grains with relatively preferred orientation. The thickness formed in our Cr buffer layer and DLC coating layer were obtained the 487 nm and $1.14\;{\mu}m$. The average friction coefficient of Cr-DLC films considerably decreased to 0.15 for 0.50 of uncoated SCM415 material. The hardness and surface roughness of Cr-DLC films were measured 20 GPa and 10.76 nm, respectively. And then, efficiency tests were performed on the hydraulic gear pump to investigate the efficiency performance of the Cr-DLC coated spur gear. The experimental results show that the volumetric and mechanical efficiency of hydraulic gear pump using the Cr-DLC spur gear were improved up to 2~5% and better efficiency improvement could be attributed to its excellent microstructure, higher hardness, and lower friction coefficient. This conclusion proves the feasibility in the efficiency improvement of hydraulic gear pump for industrial applications.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.3
• /
• pp.232-239
• /
• 2013

Thin light-active layers of the $CuInSe_2$ solar cell were prepared on Mo-coated sodalime glass substrates by one-step electrodeposition and post-annealing. The structure, morphology, and composition of $CuInSe_2$ film could be controlled by deposition parameters, such as the composition of metallic precursors, the concentration of complexing agents, and the temperature of post-annealing with elemental selenium. A dense and uniform Cu-poor $CuInSe_2$ film was successfully obtained in a range of parametric variation of electrodeposition with a constant voltage of -0.5 V vs. a Ag/AgCl reference electrode. The post-annealing of the film at high temperature above $500^{\circ}C$ induced crystallization of $CuInSe_2$ with well-developed grains. The KCN-treatment of the annealed $CuInSe_2$ films further induced Cu-poor $CuInSe_2$ films without secondary phases, such as $Cu_2Se$. The structure, morphology, and composition of $CuInSe_2$ films were compared with respect to the conditions of electrodeposition and post-annealing using SEM, XRD, Raman, AES and EDS analysis. And the conditions for preparing device-quality $CuInSe_2$ films by electrodeposition were proposed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.817-820
• /
• 2004

The $Sr_{0.7}Bi_{2.6}Ta_2O_9$(SBT) thin films are deposited on Pt-coated electrode($Pt/TiO_2/SiO_2/Si$) using a RF magnetron sputtering method. The ferroelectric properties of SBT capacitors with annealing time were studied. In the SEM images, Bi-layered perovskite phase was crystallized at 10min and grains largely grew with annealing tune. SBT thin films are transformed from initial amorphous phase to the fully formed layer-structured perovskite. During the annealing process at $750^{\circ}C$, we found that an fluorite-like stage is formed after 3min. In the XRD pattern, the SBT thin films after 3min annealing time had (105) orientation. The ferroelectric properties of SBT capacitor with annealing time represent a favorable properties at 60 min. The maximum remanent polarization and the coercive electric field with 60 min are $12.40C/cm^2$ and 30kV/cm, respectively. The leakage current density with 60min is $6.81{\times}10^{-10}A/cm^2$.

• Journal of Convergence for Information Technology
• /
• v.11 no.3
• /
• pp.167-173
• /
• 2021

There is an increasing interest in manufacturing various electronic devices on a bendable substrate. In this paper, we observed a surface morphology by annealing for 20 minutes at temperatures of 150 ℃, 350 ℃, and 550 ℃, respectively, with samples coated by chromium and aluminum. Data on surfaces are investigated using high-resolution SEM and AFM that can measure roughness up to nm. There is no difference from the sample without heat treatment up to 350 ℃, but the change of crystal grains can be observed at 550 ℃. In the future, for application to the flexible optoelectronic field, additional characteristics such as electrical conductivity and reflectivity will be analyzed and optical devices will be manufactured. In conclusion, we will explore the possibility of applying metal materials to flexible electronic devices.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.222-222
• /
• 2012

Metal oxide gas sensors based on semiconductor type have attracted a great deal of attention due to their low cost, flexible production and simple usability. However, most works have been focused on n-type oxides, while the characteristics of p-type oxide gas sensors have been barely studied. An investigation on p-type oxides is very important in that the use of them makes possible the novel sensors such as p-n diode and tandem devices. Monoclinic cupric oxide (CuO) is p-type semiconductor with narrow band gap (~1.2 eV). This is composed of abundant, nontoxic elements on earth, and thus low-cost, environment-friendly devices can be realized. However, gas sensing properties of neat CuO were rarely explored and the mechanism still remains unclear. In this work, the neat CuO layers with highly ordered mesoporous structures were prepared by a template-free, one-pot solution-based method using novel ink solutions, formulated with copper formate tetrahydrate, hexylamine and ethyl cellulose. The shear viscosity of the formulated solutions was 5.79 Pa s at a shear rate of 1 s-1. The solutions were coated on SiO2/Si substrates by spin-coating (ink) and calcined for 1 h at the temperature of $200{\sim}600^{\circ}C$ in air. The surface and cross-sectional morphologies of the formed CuO layers were observed by a focused ion beam scanning electron microscopy (FIB-SEM) and porosity was determined by image analysis using simple computer-programming. XRD analysis showed phase evolutions of the layers, depending on the calcination temperature, and thermal decompositions of the neat precursor and the formulated ink were investigated by TGA and DSC. As a result, the formation of the porous structures was attributed to the vaporization of ethyl cellulose contained in the solutions. Mesoporous CuO, formed with the ink solution, consisted of grains and pores with nano-meter size. All of them were strongly dependent on calcination temperature. Sensing properties toward H2 and C2H5OH gases were examined as a function of operating temperature. High and fast responses toward H2 and C2H5OH gases were discussed in terms of crystallinity, nonstoichiometry and morphological factors such as porosity, grain size and surface-to-volume ratio. To our knowledge, the responses toward H2 and C2H5OH gases of these CuO gas sensors are comparable to previously reported values.

• Korean Journal of Materials Research
• /
• v.19 no.2
• /
• pp.61-67
• /
• 2009

Electrolessly deposited Co (Re,P) was investigated as a possible capping layer for Cu wires. 50 nm Co (Re,P) films were deposited on Cu/Ti-coated silicon wafers which acted as a catalytic seed and an adhesion layer, respectively. To obtain the optimized bath composition, electroless deposition was studied through an electrochemical approach via a linear sweep voltammetry analysis. The results of using this method showed that the best deposition conditions were a $CoSO_4$ concentration of 0.082 mol/l, a solution pH of 9, a $KReO_4$ concentration of 0.0003 mol/l and sodium hypophosphite concentration of 0.1 mol/L at $80^{\circ}C$. The thermal stability of the Co (Re,P) layer as a barrier preventing Cu was evaluated using Auger electron spectroscopy and a Scanning calorimeter. The measurement results showed that Re impurities stabilized the h.c.p. phase up to $550^{\circ}C$ and that the Co (Re,P) film efficiently blocked Cu diffusion under an annealing temperature of $400^{\circ}C$ for 1hr. The good barrier properties that were observed can be explained by the nano-sized grains along with the blocking effect of the impurities at the fast diffusion path of the grain boundaries. The transformation temperature from the amorphous to crystal structure is increased by doping the Re.

• Journal of the Mineralogical Society of Korea
• /
• v.29 no.2
• /
• pp.79-87
• /
• 2016

Asian dust (Hwangsa) interacts with light, atmospheric gas, aerosol, and marine ecosystem, affecting Earth climate. Mineralogical properties are essential to understand the interaction between the dust and environments. In this study, we examined the mineralogical properties of Asian dust collected at Deokjeok Island, Incheon, Korea in February 22, 2015. X-ray diffraction (XRD) analyses showed that phyllosilicate minerals (62 wt%) dominate the Asian dust. Illite-smectite series clay minerals (55%) were common with minor chlorite (5%) and kaolinite (2%). Non-phyllosilicate minerals were quartz (18%), plagioclase (10%), K-feldspar (4%), calcite (4%), and gypsum (1%). Similar results were obtained by mineral quantification using scanning electron microscopy (SEM) and energy dispersive X-ray spectrometry (EDS). Transmission electron microscopy combined with EDS confirmed illite-smectite series clay minerals as the dominant phyllosilicate type. Morphological analyses using SEM showed clay agglomerates, clay-coated quartz, feldspars, and micas. Gypsum grains were common on the particle surface, while calcite nanofibers, previously reported as common on the surface, were rare, indicating the reaction of calcite and acidic atmospheric pollutants to form gypsum. The analytical result of 2015 Asian dust would contribute to the establishment of mineralogical base for the modeling of the interaction between Asian dust and environments.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.65-65
• /
• 2012

Copper zinc tin sulfide ($Cu_2ZnSnS_4$, CZTS) is a very promising material as a low cost absorber alternative to other chalcopyrite-type semiconductors based on Ga or In because of the abundant and economical elements. In addition, CZTS has a band-gap energy of 1.4~1.5eV and large absorption coefficient over ${\sim}10^4cm^{-1}$, which is similar to those of $Cu(In,Ga)Se_2$(CIGS) regarded as one of the most successful absorber materials for high efficient solar cell. Most previous works on the fabrication of CZTS thin films were based on the vacuum deposition such as thermal evaporation and RF magnetron sputtering. Although the vacuum deposition has been widely adopted, it is quite expensive and complicated. In this regard, the solution processes such as sol-gel method, nanocrystal dispersion and hybrid slurry method have been developed for easy and cost-effective fabrication of CZTS film. Among these methods, the hybrid slurry method is favorable to make high crystalline and dense absorber layer. However, this method has the demerit using the toxic and explosive hydrazine solvent, which has severe limitation for common use. With these considerations, it is highly desirable to develop a robust, easily scalable and relatively safe solution-based process for the fabrication of a high quality CZTS absorber layer. Here, we demonstrate the fabrication of a high quality CZTS absorber layer with a thickness of 1.5~2.0 ${\mu}m$ and micrometer-scaled grains using two different non-vacuum approaches. The first solution-processing approach includes air-stable non-toxic solvent-based inks in which the commercially available precursor nanoparticles are dispersed in ethanol. Our readily achievable air-stable precursor ink, without the involvement of complex particle synthesis, high toxic solvents, or organic additives, facilitates a convenient method to fabricate a high quality CZTS absorber layer with uniform surface composition and across the film depth when annealed at $530^{\circ}C$. The conversion efficiency and fill factor for the non-toxic ink based solar cells are 5.14% and 52.8%, respectively. The other method is based on the nanocrystal dispersions that are a key ingredient in the deposition of thermally annealed absorber layers. We report a facile synthetic method to produce phase-pure CZTS nanocrystals capped with less toxic and more easily removable ligands. The resulting CZTS nanoparticle dispersion enables us to fabricate uniform, crack-free absorber layer onto Mo-coated soda-lime glass at $500^{\circ}C$, which exhibits a robust and reproducible photovoltaic response. Our simple and less-toxic approach for the fabrication of CZTS layer, reported here, will be the first step in realizing the low-cost solution-processed CZTS solar cell with high efficiency.

• Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
• /
• 2002.08a
• /
• pp.109-119
• /
• 2002

Rice production in Korea began to rise significantly after 1970. Rice is the dominant food in Korea and most of the rice production (about 95%) is consumed as cooked rice. it provides over 4,000Kj of energy per capita per day. Apparent rice availability in 2000, 93.6Kg of milled rice per person annually. The non-allergenic character of rice offers a sound basis for development of products for markets for all age groups. Whole grains are washed rice, coated rice, enriched rice in Korea. Utilization of rice as food can be categorized three categories in Korea; direct food use, processed foods, and brewing. Rice for direct consumption include regular whole grain, precooked rice, brown rice and specialty products such as aseptic cooked rice, retort cooked rice and rice burger. Rice used for processed foods includes that for cereal, soup, baby food, snack, cake, noodle, brown rice tea, and minor unclassified uses. Rice use for brewing is for the production of fermented rice wine. The use of rice for direct food is by for the greatest of the three uses. Although direct food accounts for the largest domestic consumption, a significant quantity of rice is used in processed products. The use of rice by-products as human food should not be over looked. Utilization of by products(rice germ, rice bran) requires a specialized technology. Typical type of rice is black rice. When cooked, black rice gives a black color to cooked rice. Glutinous rice performs specific functions in several commercial products such as dessert, gravis, cake and snack. Rice starch production is quite limited because of the high cost of making of starch. Rice processed products in Korea are occupied small parts of total rice production compared to Japan. Rice cake (Garadog) is the principal from of rice product consumed in Korea. Rice cake and snack is usually prepared from non-glutinous milled by washing, grinding, steaming, cooling and packaging. Rice cake will be continued to be a major rice product in Korea. Rice products represent a means to study variety differences in rice grain quality, since the processing magnifies differences not normally detected from more boiling. Recently, rice processing companies in Korea are about 400 ones which uses rice about 160,000tons. New rice processed products and modified traditional products must be developed and diversified with high quality and processing properties of rice processed products are improved.