• Korean Journal of Materials Research
• /
• v.14 no.10
• /
• pp.731-736
• /
• 2004

Herein, we report on the co-firing of a low-K wiring substrate and a middle-K functional substrate in LTCC. Firstly, we researched the sintering behavior and dielectric properties of the low-k wiring substrate comprised by alumina and glass frit with ${\varepsilon}_r$, of $\sim7$ and the middle-k functional substrate comprised by $Ba_{5}Nb_{4}O_{15}$ and glass frit with ${\varepsilon}_r$, of $20\sim30$. The warpage and delamination between the hetero layers of the low-K and the middle-K composition were also studied. In particular, physical matching of the hetero layers could be possible by adjusting of the sintering properties of the composition. We observed that an introduction of the glass frit to the low- and middle-K substrate gives rise to a minimization of an effect given by separation of the hetero layers, and modification of the fraction of the glass frit accompanied by a variation of the composition could control the sintering behavior and its beginning temperature. In the case of co-firing of the L03 as the low-K wiring substrate composition and the M03 as the middle-K functional substrate composition at $875^{\circ}C$, we could fabricate a desirable structure of hetero layers without any kinds of structural defects such as separation, warpage, delamination, pore trap, etc. We suppose that the co-firing techniques described in this study would provide a helpful method to fabricate a LTCC multi-functional for the next generation.

• Journal of electromagnetic engineering and science
• /
• v.5 no.3
• /
• pp.140-145
• /
• 2005

In this paper, an experimental investigation for return loss and a software-based prediction for interference level of single-packaged filtering antenna composed of dielectric waveguide filter and PCB(Printed Circuit Board) slot antenna in transceiver module have been carried out with several different feeding structures in millimeter-wave regime. The implementation and embedding method of the existing air-filled waveguide filters working at millimeter-wave frequency on general PCB substrate have been described. In a view of the implementation of each components, the dielectric waveguide embedded in PCB and LTCC(Low Temparature Co-fired Ceramic) substrates has employed the via fences as a replacement with side walls and common ground plane to prevent energy leakage. The characteristics of several prototypes of filtering antenna embedded in PCB substrate are considered by comparing the wideband and transmission characteristics as a function of bent angle of transmission line connecting two components. In addition, as an essential to the packaging of transceiver module working at millimeter-wave, miniaturization technology maintaining the performances of independent components and the important problems caused by integrating and connecting the different components in different layers are described in this paper.

• 한국연소학회:학술대회논문집
• /
• 2006.10a
• /
• pp.137-144
• /
• 2006

Oil-fired power plants usually use several burners and the combustion air is supplied to each burner through the complicated duct which is called windbox. A windbox should be designed to supply combustion air to each burner evenly but, due to the complicated duct shape, flow distribution in the windbox is unbalanced and uneven supplies of combustion air to each burner are induced by these unbalanced flow distribution in the windbox. These flow patterns tend to make flame unstable, increase the formation of pollutants and lower the overall combustion efficiency. To prevent these disadvantages, flow patterns in the windbox should be investigated for the uniform flow distribution. In this study, computational simulation method was used to investigate the flow distribution in the windbox and measured the velocities at the exit of burners in the real windbox to compare with CFD results. The results show two significant flow patterns. One is that the flow rates of each burner are different from each other and this means that all burners operate in different conditions of air to fuel ratio. The other is that the flow distribution at the exit of each burner is not axi-symmetric although the burner shape is axi-symmetric and this increases the pollutant products like CO.

• Journal of electromagnetic engineering and science
• /
• v.10 no.1
• /
• pp.28-34
• /
• 2010

This paper introduces a new U.S. ultra-wideband(UWB: 3.1~10.6 GHz) 1:2 power divider based on a single section Wilkinson type configuration. The divider provides very flat in-band power splitting, high isolation, low insertion loss, sharp roll-off bandpass filtering, and DC blocking characteristics. The circuit consists of a $\lambda$/4 Y resonator, three capacitively coupled $\lambda$/2 short-circuited lines, and a resistor between the two output ports. The circuit structure was simulated with ADS and HFSS, and realized with low-temperature co-fired ceramic(LTCC) green tape, which has a dielectric constant of 7.8. $|S_{11}|$ better than 10 dB, $|S_{21}|$ and $|S_{31}|$ less than 3.2 dB, with both $|S_{22}|$ and $|S_{32}|$ measured as better than 12 dB for the whole UWB band. Measurement results agree closely with HFSS simulation results. The power divider has a compact size of $4\times9\times0.6mm^3$.

• Journal of the Korean Ceramic Society
• /
• v.49 no.3
• /
• pp.216-220
• /
• 2012

Mullite formation in a porcelain body was promoted extensively by replacing kaolinite with pyrophyllite. Effects of mullite formation and vitrification by substitution of kaolinite with pyrophyllite on the mechanical and thermal properties were investigated. Addition of 45-55% pyrophyllite (pyrophyllite (45-55%)-feldspar (30%)-Gairome clay (20%)) could vitrify the sintered samples (water absorption : 0.05%, bulk density : 2.66g/cc) and improve the flexural strength (122MPa) when fired at $1280^{\circ}C$. Mullite formation was found to be decreased with increasing content of pyrophyllite. On the contrary, beyond 50% of pyrophyllite quartz and cristobalite phases was found to be increased. Thermal expansion coefficient of the samples decreased with increase of mullite phase. In triaxial system of pyrophyllite-feldspar-clay, the mullite formation of the samples with 50% pyrophyllite reaches about 78.7% and thermal expansion coefficient was found to be $5.4{\times}10^{-6}/K$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.117-117
• /
• 2009

Recently, low temperature co-fired ceramic (LTCC) technology has gained a remarkable application potential in sensors, actuators and microsystems fields. In this study, we investigated the effects of annealing treatment on the electrical properties of $Pb(ZrTi)O_3$ (PZT) thin films deposited on LTCC substrate. The LTCC substrates with thickness of 400 ${\mu}m$ were fabricated by laminating 12 green tapes which consist of alumina and glass particle in an organic binder. The PZT thin films were deposited on Au/LTCC substrates by RF magnetron sputtering method. Then, the change of the crystallization of the films was investigated under various annealing temperatures. The results showed that the crystallization of the films were enhanced as increasing annealing temperatures. The film, annealed at $700^{\circ}C$, 3min, was well crystallized in the ferovskite structure. The structural variation of the films were analyzed by using X-Ray diffraction (XRD) and field emmision scanning electron microscopy (FESEM).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.118-118
• /
• 2009

Low temperature co-fired ceramic (LTCC) is one of promising materials for MEMS structures because it has very good electrical and mechanical properties as well as possibility of making various three dimensional (3D) structures. In this work, piezoelectric pressure sensors based on hybrid LTCC technology were presented. The LTCC diaphragms with thickness of 400 um were fabricated by laminating 12 green tapes which consist of alumina and glass particle in an organic binder. The piezoelectric sensing layer consists of $Pb(ZrTi)O_3$ (PZT) thin film deposited by RF magnetron sputtering method on between top and bottom Au electrodes. The results showed that the fabrication method is very suitable for pressure sensor applications. The PZT films deposited on LTCC diaphragms were successfully grown and were analyzed by using X-ray diffraction method (XRD) and field emission scanning electron microscope (FESEM).

• Journal of Powder Materials
• /
• v.25 no.3
• /
• pp.232-239
• /
• 2018

In this paper, the recovery and nanoparticle synthesis of Ag from low temperature co-fired ceramic (LTCC) by-products are studied. The effect of reaction behavior on Ag leaching conditions from the LTCC by-products is confirmed. The optimum leaching conditions are determined to be: 5 M $HNO_3$, a reaction temperature of $75^{\circ}C$, and a pulp density of 50 g/L at 60 min. For the selective recovery of Ag, the [Cl]/[Ag] equivalence ratio experiment is performed using added HCl; most of the Ag (more than 99%) is recovered. The XRD and MP-AES results confirm that the powder is AgCl and that impurities are at less than 1%. Ag nanoparticles are synthesized using a chemical reduction process for recycling, $NaBH_4$ and PVP are used as reducing agents and dispersion stabilizers. UV-vis and FE-SEM results show that AgCl powder is precipitated and that Ag nanoparticles are synthesized. Ag nanoparticles of 100% Ag are obtained under the chemical reaction conditions.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.939-944
• /
• 2001

For the application of simultaneous $DeSO_{2}\;&\;DeNO_{x}$ equipment using non-thermal plasma process to the industrial and power plants, the many types of plasma device and process were studied. The e-beam and pulsed plasma corona discharge process are outstanding for the study to apply commercial large-scale plant from among these. In this paper, non-thermal plasma of technical trends and the characteristics of system developed by Doosan heavy industries & construction Co., Ltd. are explained. We have researched pulsed plasma corona discharge process since 1994. At the basis of reasonable results for the pilot plant, we constructed the demonstration plant at a domestic coal-fired power plant in 1999, as the previous step for commercial use. In near future, enough information about designs and costs of commercial-size system will be obtained.

• The Journal of Korean Academy of Prosthodontics
• /
• v.29 no.3
• /
• pp.111-119
• /
• 1991

This study was performed to investigate the effect of gold electrodepositoin on porcelain color of palladium-silver alloy. The specimens were made by firing porcelain on the metal plates cast respectively in Au-Pt alloy, and Pd-Ag alloy. In the case of Pd-Ag alloy specimens, porcelain were fired under three different conditions of the metal plate: 1) without gold coating, 2) firing opaque beforehand on one side, gold coating on the other side, 3) gold coating on both sides of the metal plate. Color change was measured with fiber-optic colorimeter(Model TC-6FX, Tokyo Denshoku Co., Japan). The obtained results were as follows: 1. In the group of firing opaque beforehand on one side and gold coating on the other side, there was no significant differences in their color in comparison to the color of the control group of the Au-Pt alloys. 2. In the group of gold coating on both sides on metal plate, there were no significant differences except their value to the group of firing poaque beforehand on one side and gold coating on the other side.