• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.115-116
• /
• 2023

This study aims to investigate and improve the carbon dioxide sequestration capability and the mechanical properties of non-hydraulic low calcium silicate cement especially designed for CO₂ reaction and ordinary Portland cement subjected to the carbonation curing facilitating pH swing method. Nitric acid (HNO₃) was utilized as an liquid for the mixing of cement paste to enhance the initial dissolution of Ca ions from the cements by promoting low pH environment and prevent the direct precipitation of Ca with the anion, owing to the high solubility of Ca(NO₃)₂ in water. The results presented that the higher the concentration of HNO₃, the higher the compressive strength and CO₂ sequestration (until 0.1 M). Ca dissolution caused by the harsh acid attack onto the anhydrous cement particle lead to the higher carbonation reaction degree, forming abundant CaCO₃ crystals after the reaction. However, cement paste mixed with excessively high concentration of HNO₃ presented deterioration due to the too harsh pH environment and abundant NO₃- ions which are known to retard the reaction of cement.

• 한국연초학회지
• /
• 제20권2호
• /
• pp.160-165
• /
• 1998

The Joint curing barns for flue-cured tobacco is a favorite with the tobacco farmers in Korea. However, most of farmer utilizing the joint curing barns indicated many problems such as high temperature and noise in the working room and a dry of cured leaves in the storage room. A structure of Joint curing barns has been modified to meet the needs of tobacco farmers. Compared with the unimproved joint curing barns, the improved one showed that the noise of workshop decreased about 7.7～10.8db, the amount of $CO_2$ decreased 40～50ppm in a working room and 80～100ppm in a machine room. Ammonia gas decreased 0.29mg/㎥ and the temperature of a working room dropped about 2.1～3.5$^{\circ}C$. The amount of air flow in a working room increased 23.2% at a site being 2m away from the entrance and 30.8% at a center. The inner temperature of the improved storage room showed that maximum temperature dropped about 3$^{\circ}C$, minimum temperature was high about 2$^{\circ}C$. The highest relative humidity was low 6%, the lowest one increased high about 10% when compared with the unimproved joint curing barns.

• 한국추진공학회지
• /
• 제20권1호
• /
• pp.37-42
• /
• 2016

본 연구에서는 HTPB를 적용한 고체추진제의 공정간 검사를 위해 경화제를 넣기 전과 넣은 후의 미 경화 추진제의 연소속도를 검토하였다. 그리고 경화제를 넣기 전 미 경화 추진제의 연소속도는 압력 1000 psi에서 약 9.7 mm/s 정도이며, 시간에 따른 연소속도 변화는 없었다. 경화제가 들어간 미 경화 추진제의 연소속도는 약 8.1 mm/s로 시간에 따라 느려지는 경향을 보였다. 경화반응 속도가 느린 미 경화 추진제는 시간에 따라 연소속도가 서서히 느려졌으며, 경화반응 속도가 빠른 미 경화 추진제는 연소속도가 빠르게 느려지는 것을 확인할 수 있었다. 그리고 완전히 경화된 추진제의 연소속도는 약 6.8 mm/s 정도로 가장 느린 것으로 나타났다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.242-242
• /
• 2006

Increasingly complex tasks are performed by computers or cellular phone, requiring more and more memory capacity as well as faster and faster processing speeds. This leads to a constant need to develop more highly integrated circuit systems. Therefore, there have been numerous studies by many engineers investigating circuit patterning. In particular, PCB including module/package substrates such as FCB (Flip Chip Board) has been developed toward being low profile, low power and multi-functionalized due to the demands on miniaturization, increasing functional density of the boards and higher performances of the electric devices. Imprint lithography have received significant attention due to an alternative technology for photolithography on such devices. The imprint technique. is one of promising candidates, especially due to the fact that the expected resolution limits are far beyond the requirements of the PCB industry in the near future. For applying imprint lithography to FCB, it is very important to control thermal properties and mechanical properties of dielectric materials. These properties are very dependent on epoxy resin, curing agent, accelerator, filler and curing degree(%) of dielectric materials. In this work, the epoxy composites filled with silica fillers and cured with various accelerators having various curing degree(%) were prepared. The characterization of the thermal and mechanical properties wasperformed by thermal mechanical analysis (TMA), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), rheometer, an universal test machine (UTM).

• Composites Research
• /
• 제13권4호
• /
• pp.42-53
• /
• 2000

차세대 항공기소재로 관심을 가지고 있는 Al 7075/CFRP 적층 복합재인 CARALL(CARbon ALuminum Laminates)하이브리드 복합소재 제조를 위한 중요조건중의 하나인 Al 표면처리조건과 경화방법에 대해 조사하였다. 항공기용 Al 전처리 중 대표적인 것으로 증기탈지, 크롬산 양극산화 피막처리, 황산-중크롬산 나트륨 에칭처리 및 인산 양극산화 피막처리공정이 있다. 본 실험에서는 상기 전처리 공정을 모두 항공 규격에 준해서 실시하여 Lap shear 및 Bell peel strength를 비교함으로써 효과적인 접착강도를 나타내는 표면처리 공정을 찾아내고, 시편의 자연표면상태를 그대로 관찰할 수 있는 AFM(Atomic Force Microscope)장비를 이용하여 각 전처리 시편의 표면형상을 측정함으로써 표면형상과 접착강도와의 상관관계를 고찰 하였다. 그리고 Al 표면처리와 별도로 Al과 접착제 및 탄소섬유 프리프레그를 동시에 경화시키는 방법과 탄소섬유 프리프레그를 미리 경화시킨후 다시 Al과 탄소섬유 라미네이트를 접착필름을 이용하여 재 접착시키는 이차 경화법을 적용하여 상호 접착강도 및 물성을 비교하였다. 또한 이차경화법에서의 오토클레이브 압력 변화와 DMA(Dynamic Mechanical Analysis) 장비를 이용한 접착필름의 유리전이온도($T_g$) 측정을 통해 효과적인 공정압력 및 접착내구성 유지에 필요한 최소 경화시간을 파악하였다. 상기 결과로부터 정밀 치수관리가 필요하며 고접착강도, 내구성 항공기 부품을 제작하기 위한 알루미늄 표면처리 공정과 복합재 경화공정 조건을 제시하고자 하였다.

• The Korean Journal of Ceramics
• /
• 제6권2호
• /
• pp.103-106
• /
• 2000

The effects of replacement level, curing method and chemical admixtures were investigated in the cement-fly ash paste. The strength of cement-fly ash paste is lower than that of controlled cement paste only and the differences increase with replacement level. However, in steam curing, strength of cement-fly ash pastes is improved, especially, at early ages. In order to improve early strength, the use of $Na_2SO_4$in cement-fly ash paste increases the quality of concrete. In addition, improvement of strength of concrete including 30% of fly ash can be obtained and achieves the highest strength compared to other concrete mixtures.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 춘계 학술논문 발표대회
• /
• pp.33-34
• /
• 2013

Recently, as the policy of state that it is the low carbon green growth is promoted, the effort for reducing the CO₂ gas generation ejected from the construction industry in the cement production is continued. That is, the method using the mineral admixtures including the silica fume and red mud, silica fume and etc. it is the industrial byproduct with the method solving the exhaustion problem of the environmental contamination settlement and natural resources, the great quantity as the cement substitute material is examined. Accordingly, in this research, the strength characteristic of the curing body differentiating the curing method of the ternary system inorganic binder using the blast furnace slag and red mud, silica fume and etc. as the cement substitute material tried to be examined.

• 도시과학
• /
• 제11권1호
• /
• pp.21-28
• /
• 2022

Raman spectroscopy is effective to investigate functional groups via molecular vibration. The technique offers the structural information of compounds including subtle changes in the chemical composition of local atomic coordination without critical damage. Thus, the effect of carbonation on the hydration characteristics of Portland cement under pre-curing conditions for carbonation was investigated via Raman spectroscopy in the present study. Gaseous CO₂ was injected within 60 seconds, and the reaction time was varied from 0 minute to 90 minutes. The test results indicated that the Ca/Si ratio of C-S-H reduced immediately after mixing and then the C-S-H with a relatively high Ca/Si ratio coexisted as the reaction time increased. The calcium carbonates formed in the present study included calcite and amorphous calcium carbonates. The test results via Raman spectroscopy provide valuable information about the carbonation characteristics of OPC under pre-curing conditions for carbonation.

• 콘크리트학회논문집
• /
• 제20권5호
• /
• pp.543-548
• /
• 2008

프리캐스트 제품은 소요의 강도를 단기간에 얻기 위하여 일반적으로 상압 증기양생을 실시하며, 칼슘-실리케이트의 수열합성반응을 이용할 경우 1차 양생 이후에 오토클레이브 양생이라는 2차 양생도 실시하고 있다. 여기에서 제품의 강도발현에 커다란 영향을 미치는 양생 방법의 경우, 2차 양생 방법에 대한 연구는 각종 연구로 부터 수열반응에 적합한 조건이 구명되는 등 많은 연구가 수행되었으나, 1차 양생 방법에 대한 검토는 아직 미비한 실정이며 생산업체별로 양생 방식을 달리하여 제품을 생산하고 있어 제품의 소요강도 획득에 문제점을 가지고 있다. 이에 본 연구에서는 수열합성 경화체에 있어서 보다 높은 강도를 얻기 위한 1차 양생 방법에 대한 자료를 얻고자 실험적 연구를 수행하였다. 즉 수열합성 경화체에 있어서 1차 양생 방법을 건식과 건/습식 그리고 습식으로 실시한 후에 각각의 시험체에 대하여 수화특성을 알아보기 위하여 SEM, XRD, DT-TGA 및 porosimeter 시험을 실시하였으며, 강도 특성을 알아보기 위하여 압축강도 시험을 실시하였다. 측정 결과, 1차, 2차 양생 후 각 양생조건에 따른 시험체의 압축강도는 건/습식 양생조건이 강도발현에 유리한 것으로 나타났으며, 그 차이는 크지 않은 것을 알 수 있었다. 수화도 분석을 위한 SEM, XRD 및 DT-TGA의 측정 결과, 건/습식 양생조건의 경우가 건식과 습식 양생조건에 비해 가장 많이 수화가 진행된 것을 알 수 있었고, porosimeter의 측정 결과에 있어서도 건/습식 양생조건이 강도특성에 유리한 공극특성을 갖는 것으로 나타났다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2022년도 가을 학술논문 발표대회
• /
• pp.187-188
• /
• 2022

In this study, the compressive strength and carbonation properties of geopolymer paste according to the amount of alkali admixture added were evaluated for the development of geopolymer concrete that recycles industrial waste. A geopolymer paste specimen was prepared using Ca(OH)2 as an admixture, and the prepared specimen was standard cured for 28 days. After curing, the compressive strength of the specimen was measured. As the amount of alkali admixture increased, the compressive strength increased. After curing, carbonation was carried out for 7 days in a CO2 5% environment. As a result of comparative evaluation of the amount of CaCO3 produced according to carbonation, the amount of CaCO3 produced increased as the amount of Ca(OH)2 added increased. However, when the amount of admixture added exceeds 5%, the increase rate decreases, so the optimum addition rate is considered to be 5%.