• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1988.05a
• /
• pp.46-48
• /
• 1988

The effect of cold reduction ratio on magnetic properties of 45% Ni-Fe permalloy was studied. To know the relationship between the crystal orientation and the magnetic properties, the pole figure was measured by X-ray diffraction method. In the case of single rolled reduction, the coercive force decreased with cold reduction ratio monotonically, but the maximum permeability, induction and squreness increased drastically. In the case of double rolled reduction (total reduction ratio is 90%), the saturation and residual induction increased slightly with secondary reduction ratio, but the maximum permeability and the coercive force had the maximum and the minimum value at the 50/50% reduction ratio respectively. And strong {100} <100> pole was developed by increasing the cold reduction ratio.

• Journal of the Korean institute of surface engineering
• /
• v.19 no.1
• /
• pp.3-12
• /
• 1986

Influences of pH, temperature, and composition of bath on the deposition rate and the magnetic properties were studied for two kinds of electroless Co-P plating bath. The results obtained are as follows. Ammonia alkaline citrate bath was more stable than ammonia alkaline tartrate bath, and the film deposited from citrate bath gave a higher squareness. The magnetic properties of the film obtained from citrate bath greatly depended upon pH. Under the optimum conditions, the film deposited from citrate bath had coercive force of 330 Oe and squareness of 0.67. However the films deposited from tartrate bath had coercive force of 300 Oe and squareness of 0.58.

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.389-393
• /
• 2000

Effects of Co addition and heat treatment on the magnetic properties of Fe-Si-B thin films were investigated. The compositions of metalloids, i.e, B and Si, in the alloys were kept 10 at.% each. Heat treatments were carried out in the temperature range from 100 to $300^{\circ}C$ for up to 60 min. Amorphous thin films of FeCoSiB were deposited on the water-cooled substrates by dc magnetron sputtering. The composition of thin films was controlled by placing proper number of pellets of alloying elements and analyzed by ICP, resulting in $Fe_{80-X}Co_ XB_{10}Si_{10}$ (X=8~18 at.%). Saturation magnetization of the alloys increased as Co concentration increased up to 10 at.% and then decreased with further increase of Co concentration. However, coercive force of the films decreased with the increase of Co concentration. Furthermore, the coercive force was also reduced by the annealing due to the residual stress relief.

• Korean Journal of Materials Research
• /
• v.12 no.10
• /
• pp.791-795
• /
• 2002

We studied the physical properties of $Co_3$$O_4$-added Ni-Zn ferrite which were sintered at 1050~110$0^{\circ}C$ for 2 hours. X-ray diffraction showed a spinel structure, and optical microscopy showed grain sizes of 5 to 10 $\mu\textrm{m}$. As the sintering temperature was increased from $1050^{\circ}C$ to $1070^{\circ}C$, the initial permeability and magnetic induction increased, and both of the loss factor and the coercive force decreased. The Curie temperatures were about $^234~245{\circ}C$ with added $Co_3$$O_4$. The initial permeability was 350 to 420 and maximum magnetic induction density and coercive force 4870G to 4980G and 0.15 Oe to 0.21 Oe, respectively which were similar to those of Ni-Zn ferrite synthesized in the conventional process. The frequency of specimen was in the range of 1MHz to 300MHz. In the plot of initial permeability vs. frequencies, a $180^{\circ}C$ rotation of the magnetic domain could be perceived in a broad band of microwave before and after the resonance frequency.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.5
• /
• pp.413-417
• /
• 1998

In this paper, we investigate frequency dependance of inductance of FeCoB amorphous magnetic films. $(Fe_{1-x}Co_x)_{79}Si_2B_{19}$ was used as the basic composition of amorphous magnetic film having near zero magnetostriction. The amorphous magnetic films were fabricated with x=0.94 and x=0.95 by using sputtering method at high frequency. The films were anneald under non-magnetic field and near crystallization temperatures(30min at $280^{\circ}C$, 30min and 1hr at $400^{\circ}C$, respectively). As the results of the experiments with the fabricated films, the lowest coercive force was 0.084[Oe] at 400[W] of the input power and the crystallization temperature was $360^{\circ}C$ . In the case 30min at 40$0^{\circ}C$ the inductance value in the low frequency with x=0.95 was higher by 488% than that with x=0.94. The quality factor Q was below 0.7 for all samples. We obtained the highest quality value at 400[KHz] with 30min at $280^{\circ}C$ and x=0.94. The value was about 0.62. Also, the quality factor value was about 0.35 at 1[MHz] with 30min at $280^{\circ}C$ and x=0.95.

• Korean Journal of Materials Research
• /
• v.7 no.1
• /
• pp.69-75
• /
• 1997

Thin films of $Si0_2(1000{\AA})/CoNiCr(400{\AA})/Cr$ were fabricated as a function of Cr thickness by KF magnetron sputtering. The saturation magnetization, coercive force and squareness with annealing temperature for these films were investigated. The values of saturation magnetization of $SiO_2/CoNiCr/Cr$ thin films decreased as the thickness of Cr underlayer increased, whereas coercive force increased as the thickness of Cr underlayer increased. The value of Ms was 600 emu/cc and the maximum value of Hc was 550 Oe. Especially, the value of saturation magnetization was rapidly decreased $SiO_2/CoNiCr/Cr(1700{\AA})$ thin films as the annealing temperature increased And the coercive force increased as the annealing temperature increased When annealing temperature was $650^{\circ}C$, the Ms was reduced to 90 % of the as-deposited film. And the Hc was showed maximum 1600 Oe. It was thought that Cr diffusion into CoNiCr layer reduced the magnetic moment of CoKiCr layer. In addition. Hc might he increased due to grain growth perpendicular to the film plane.

• Proceedings of the KIEE Conference
• /
• 1990.07a
• /
• pp.239-242
• /
• 1990

The effect of $CaCo_3$, $SrCo_3$, $SiO_2$ and $H_3BO_3$ in the range of 0.1-1.0 wt% on strontium ferrites consisting of the magnetoplumbite phase $SrO-5.7Fe_2O_3$ were investigated. The hysteresis loop, density, demagnetization curve and the intrinsic coercive force were measured on anisotropic ferrite. The particle diameter and 0.5(wt%) of second additive $CaCo_3$ is particularly important for the properties of anisotropic ferrite. When the particle diameter is decreased from 1.98(${\mu}m$) to 1.07(${\mu}m$), the remance is increased from 2900 to 4010(G) and the coercive force from 2150 to 2850(Oe) at a sintering temperature 1230 ($^{\circ}C$). Remance Br(G), coercleve force(Oe) and maximum energy product of sample A-16 are87(%), 56(%), 67(%) of S-W model theoretical value.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.6
• /
• pp.486-492
• /
• 1998

The amorphous Co-based magnetic films have a large saturation flux density, a low coercive force, and a zero magnetostriction constant. Therefore, they have been studied for application to magnetic recoding heads and micro magnetic devices. However, it was found that the magnetic anisotropy was changed for each film fabrication processes. In this study, we investigated how to control the anisotropy of sputtered amorphous $Co_{89}Nb{8.5}Zr{2.5}$ films. After deposition, the rotational field annealing ant the uniaxial field annealing were performed under the magnetic field of 1.5 kOe. the annealing was done at the temperature range from 400 to $600^{\circ}C$ for one hour. As-deposited amorphous $Co_{89}Nb{8.5}Zr{2.5}$ thin film had saturation magnetization ($4\piM_5$) of 0.8 T, coercive force($_IH_C$) of 1.5 Oe, and anisotropy field($H_k$) of 11 Oe. The amorphous $Co_{89}Nb{8.5}Zr{2.5}$ thin films annealed by rotational field annealing at $500^{\circ}C$ for one hour was found to be isotropy, and $4\piM_5$ of 0.9 T was obtained from these films, Also, the magnetic anisotropy of as-deposited films could be controlled by uniaxial field annealing at $400^{\circ}C$ for one hour. Anisotropy field($H_k$) of 17 Oe and $4\piM_5$ of 1.0 T were obtained by this method.

• Journal of the Chungcheong Mathematical Society
• /
• v.37 no.1
• /
• pp.41-55
• /
• 2024

The nonconvex and nonsmooth optimization problem has been widely applicable in image processing and machine learning. In this paper, we propose an extension of the proximal iteratively reweighted ℓ₁ algorithm for nonconvex and nonsmooth minmization problem. We assume the co-coerciveness of a term of objective function instead of Lipschitz gradient condition, which is generalized property of Lipschitz continuity. We prove the global convergence of the proposed algorithm. Numerical results show that the proposed algorithm converges faster than original proximal iteratively reweighed algorithm and existing algorithms.

• Journal of the Korean Magnetics Society
• /
• v.5 no.1
• /
• pp.1-7
• /
• 1995

${(Fe_{0.85}Co_{0.15})}_{75}Al_{7}B_{18-x}Nb_{x}(x=2,\;4\;and\;6\;at%)\;and\;{(Fe_{0.85}Co_{0.15})}_{75}Al_{y}B_{21-y}Nb_{4}(y=3,\;5,\;7,\;9\;at%)$ alloys were prepared by a single-roll quenching method. Microstructure and magnetic properties of the alloys such as saturation magnetization, initial permeability, coercive force and power loss have been investigated as functions of composition and armea1ing temperature. Nanocrystallines are obtained by armealing of as-prepared amorphous alloys in all compositions except the alloy of 9 at% AI. Saturation magnetization increases after armea1ing and, decreases with Nb content. However, AI and B affects the saturation magnetization insignificantly. Initial perrreability of nanocrystallized alloy at 50 kHz is improved roore than twice compared to that of the as-prepared alloy. Coercive force and core loss reach less than half after armea1ing.