• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.11
• /
• pp.2723-2729
• /
• 1993

Moire principles are applied to the measurement of the spindle radial error motion. As opposed to conventional techniques, no master cylinder or ball is needed in the measurement so that the offset and out-of-roundness errors of the master can be inherently eliminated. Two periodic circular gratings are used, one is made on the spindle and the other is held stationary on the reference frame. When the two gratings are seen superimposed during spindle rotation, an interference fringe pattern is observed from which the information on the eccentricity between the two gratings can be extracted with high precision. The optical design and fringe analysis techniques of a prototype measurement system are described in detail with exemplary measurement results.

• KSTLE International Journal
• /
• v.5 no.1
• /
• pp.32-35
• /
• 2004

The purpose of this study is to investigate the effects of the structure and mechanical properties of laser-processed pads on their polishing behavior such as their removal rate and WIWNU (within wafer non-uniformity) during the chemical mechanical planarization (CMP) process. The holes on the pad acted as the reservoir of slurry particles and enhanced the removal rate. Without grooves, no effective removal of wafers was possible. When the length of the circular-type grooves was increased, higher removal rates and lower wafer non-uniformity were measured. The removal rate and non-uniformity linearly increased as the elastic modulus of the top pad increased. Higher removal rates and lower non-uniformity were measured as the hardness of the pad increased.

• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 2007.02a
• /
• pp.181-188
• /
• 2007

In this paper, the management thoughts of The network-manufacture based on virtual-agile organization is Brief summarized, then an explanation had been made about the virtual circulation economy patterns paradigm, which is integrated the virtual-agile manufacture and circulation economy theory, the critical content of this paradigm, at last we recognized the virtual-agile organization pattern circulation economy is one important trend of the network-manufacture development in the future.

• Structural Engineering and Mechanics
• /
• v.55 no.2
• /
• pp.263-280
• /
• 2015

This paper describes a study of the collision of hard steel spheres against aluminium thin circular plates at speeds up to 140 m/s. The tests were monitored by a high speed camera and a chronoscope, which allowed the determination of the ballistic limit and the plate deformation pattern. Quasi-static material parameters were obtained from tests on a universal testing machine and dynamic mechanical characterization of two aluminium alloys were conducted in a split Hopkinson pressure bar. Using a damage model, the perforation of the plates was simulated by finite element analysis. Axisymmetric, shell and solid elements were employed with various parameters of the numerical analysis being thoroughly discussed, in special, the dynamic model parameters. A good agreement between experiments and the numerical analysis was obtained.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.7 no.3
• /
• pp.421-434
• /
• 1995

A new instantaneous flowmeter for hydraulics by means or cylindrical chokes is developed. In this method the instantaneous flowrate through chokes is predicted in real time from measurement of pressure difference on both sides of cylindrical choke. The experimental study for the flowrate of pulsating flow in a pipe is carried out to measure differential pressure drop by using a strain gauge pressure transducer with data acquisition and processing system. A pulsating flow is verified by a visualization method. In the present study, the flow characteristic variables of laminar pulsating flow are investigated analytically and experimentally in a circular pipe. Characteristic parameters of ratio of inertia term to pressure term($\phi_{t.1}$) and ratio of viscous term to pressure term($\phi_{z.1}$) are introduced to describe the flow pattern of laminar pulsating flow.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.203-206
• /
• 2005

Reinforced concrete(RC) column-bent piers represent one of the popular piers used in highway bridges of Korea. Seismic performance of RC column-bent piers under bi-directional seismic loadings was experimentally investigated. Six column bent piers were constructed with two circular supporting columns which were made in 400 mm diameter and 2,000 mm height. Test parameters are different transverse reinforcement ratio and loading pattern. Three specimens were loaded with bi-directional lateral forces which were main cyclic loads in the longitudinal direction and sub-cyclic loads in the transverse direction. Other three specimens were loaded in the opposite way. Test results indicated that lateral strength and ductility of the latter specimens were bigger than those of the former specimens. Plastic hinge was formed with the spall of cover concrete and the fracture of the longitudinal reinforcing steels in the bottom part of two supporting columns for the former three specimens. Similar behavior was observed in the top and bottom parts of two supporting columns for the latter three specimens.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.3
• /
• pp.412-418
• /
• 1999

The scattering characteristics of a prime-focus offset-parabolic antenna are analyzed using UTD. First, ray tracing method is used to locate the shadow boundaries, and then UTD is utilized to evalute the far-zone scattered magnetic field pattern. The field components included in the UTD analysis are the reflected, edge diffracted and creeping waves. The effects of circular caps attached to both edges of a prime-focus offset-parabolic antenna are investigated by comparing the scattered magnetic field patterns with those of a knife edge parabolic reflector.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.05a
• /
• pp.135-139
• /
• 2001

This experimental study investigates the wake flow behind a pair of cylinders displaced normal to a free stream. In this experiment, the principal aim is to investigate the transition mechanism of the large vortex generating process in the wake having unique vortex shedding pattern. associated with the gap difference between the cylinders. The detailed visualization is carried out using the PIV measurement. The transition mechanism of the large generating vortex is clarified by showing the streak lines. the vorticity and the statistical fluctuating velocity distributions.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.1-4
• /
• 2004

RC column bent piers represent one of the most popular piers used in highway bridges. Seismic performance of reinforced concrete (RC) column-bent piers under bidirectional seismic loadings was experimentally investigated. Six column bent piers were constructed with two circular supporting columns. Test parameters are different transverse reinforcement and loading pattern. Three specimens were loaded with bidirectional lateral forces which were main cyclic loads in the longitudinal direction and subcyclic loads in the transverse direction. Other three specimens were loaded in the opposite way. Test results indicated that lateral strength and ductility of the latter specimens were bigger than those of the former specimens. Plastic hinge was formed with the spall of cover concrete and the fracture of the longitudinal reinforcing steels in the bottom part of two supporting columns for the former three specimens. Similar behavior was observed in the top and bottom parts of two supporting columns for the latter three specimens.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2015.07a
• /
• pp.433-434
• /
• 2015

카메라 캘리브레이션은 다시점 카메라 시스템에서 내부와 외부 인자로 이루어진 카메라 파라미터를 획득하는 과정을 의미 한다. 이는 3차원으로 표현되는 장면과 카메라간의 구조를 다루기 위해 중요하다. 그러나 카메라 캘리브레이션은 사람이 직접 손으로 각 영상에서 사각형의 네 점을 정확히 찍어 주어야 하는 과정 때문에 카메라의 수와 패턴 영상의 수가 늘어남에 따라 상당히 번거로운 작업이 된다. 본 논문에서는 카메라 캘리브레이션 과정에서 손으로 수행하는 작업을 줄이기 위해 자동으로 패턴 특징점을 탐색하는 알고리즘을 제안한다. 제안하는 방법은 먼저 영상에서 패턴 특징점의 후보를 찾기 위해 해리스 코너 검출 방법을 사용한다. 그리고 후보 주변의 원형 샘플 화소를 이용하여 유효한 패턴 특징점을 추출한다. 실험 결과는 Matlab 캘리브레이션 툴박스를 이용하여 획득한 카메라 파라미터와 비교해 보았을 때 큰 차이가 없지만 수작업의 번거로움을 상당히 감소시켰음을 확인하였다.