• 한국정밀공학회지
• /
• 제22권2호
• /
• pp.38-45
• /
• 2005

Chemical mechanical polishing(CMP) has been widely accepted for the planarization of multi-layer structures in semiconductor fabrication. But a variety of defects such as abrasive contamination, scratch, dishing, erosion and corrosion are occurred during CMP. Especially, dishing and erosion defects increase the metal resistance because they decrease the interconnect section area, and ultimately reduce the lift time of the semiconductor. Due to this reason dishing and erosion must be prohibited. The pattern density and size in chip have a significant influence on dishing and erosion occurred by over-polishing. The fixed abrasive pad(FAP) was applied and tested to reduce dishing and erosion in this paper. The abrasive concentration decrease of FAP results in advanced pattern selectivity which can lead the uniform removal in chip and declining over-polishing. Consequently, reduced dishing and erosion was observed in CMP of tungsten pattern wafer with proposed FAP and chemicals.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.434-437
• /
• 2005

Chemical Mechanical Polishing (CMP) has become an essential step in the overall semiconductor wafer fabrication technology. In general, CMP is a surface planarization method in which a silicon wafer is rotated against a polishing pad in the presence of slurry under pressure. The polishing pad, generally a polyurethane-based material, consists of polymeric foam cell walls, which aid in removal of the reaction products at the wafer interface. It has been found that the material removal rate of any polishing pad decreases due to the so-called 'pad glazing' after several wafer lots have been processed. Therefore, the pad restoration and conditioning has become essential in CMP processes to keep the urethane polishing pad at the proper friction coefficient and to allow effective slurry transport to the wafer surface. Diamond pad conditioner employs a single layer of brazed bonded diamond crystals. Due to the corrosive nature of the polishing slurry required in low pH metal CMP such as copper, it is essential to minimize the possibility of chemical interaction between very low pH slurry (pH <2) and the bond alloy. In this paper, we report an exceptional protective coated conditioner for in-situ pad conditioning in low pH Cu CMP process. The protective Cr-coated conditioner has been tested in slurry with pH levels as low as 1.5 without bond degradation.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.435-437
• /
• 2002

Polishing of copper, a process called copper chemical mechanical polishing, is a critical, intermediate step in the planarization of silicon wafers. During polishing, the electrodeposited copper films are removed by slurries: and the differential polishing rates between copper and the surrounding silicon dioxide leads to a greater removal of the copper. The differential polishing develops dimples and furrows; and the process is called dishing and erosion. In this work, we present the results of experiments on dishing and erosion of copper-CMP, using patterned silicon wafers. Results are analyzed for the pattern factors and properties of the copper layers. Three types of pads - plain, perforated, and grooved - were used for polishing. The effect of slurry chemistries and pad soaking is also reported.

• 한국재료학회지
• /
• 제22권11호
• /
• pp.587-590
• /
• 2012

Recently, the demand for the miniaturization of package substrates has been increasing. Technical innovation has occurred to move package substrate manufacturing steps into CMP applications. Electroplated copper filled trenches on the substrate need to be planarized for multi-level wires of less than $10{\mu}m$. This paper introduces a chemical mechanical planarization (CMP) process as a new package substrate manufacturing step. The purpose of this study is to investigate the effect of surfactant on the dishing and erosion of Cu patterns with the lines and spaces of around $10/10{\mu}m$ used for advanced package substrates. The use of a conventional Cu slurry without surfactant led to problems, including severe erosion of $0.58{\mu}m$ in Cu patterns smaller than $4/6{\mu}m$ and deep dishing of $4.2{\mu}m$ in Cu patterns larger than $14/16{\mu}m$. However, experimental results showed that the friction force during Cu CMP changed to lower value, and that dishing and erosion became smaller simultaneously as the surfactant concentration became higher. Finally, it was possible to realize more globally planarized Cu patterns with erosion ranges of $0.22{\mu}m$ to $0.35{\mu}m$ and dishing ranges of $0.37{\mu}m$ to $0.69{\mu}m$ by using 3 wt% concentration of surfactant.

• 마이크로전자및패키징학회지
• /
• 제13권3호
• /
• pp.47-51
• /
• 2006

디바이스의 고집적화로 인한 다층 배선구조로 인해 초점심도가 중요해짐에 따라 표면의 평탄도가 디바이스에 매우 큰 영향을 주게 되어, 표면의 평탄도를 결정지어주는 CMP(Chemical Mechanical Polishing) 공정이 매우 중요한 요소가 되었다. CMP 공정에는 슬러리, 연마패드, 컨디셔닝 디스크와 같은 소모품들이 사용된다. 이러한 소모품 중 하나인 컨디셔닝 디스크를 이용한 컨디셔닝 공정은 CMP 공정이 끝난 후 패드의 기공과 groove 내에 잔류 하는 화학반응물이나 슬러리와 같은 잔유물들을 컨디셔닝 디스크 표면에 부착되어 있는 다이아몬드를 이용하여 제거 함으로써 연마율을 높이고, 연마 패드의 수명을 증가 시켜주는 역할을 한다. 컨디셔닝 공정을 실시함으로써 연마 패드의 수명이 연장되기 때문에 경제적인 부분에서도 큰 이점을 가지게 된다. 본 연구에서는 이러한 CMP 공정에서 중요한 역할을 하는 소모품 중 하나인 컨디셔닝 디스크 표면에 존재하는 다이아몬드의 밀도, 형상 그리고 크기에 따라 연마 패드의 회복력 변화를 알아봄으로써 효율적인 컨디션닝 디스크의 특성을 평가해 보았다.

• 한국입자에어로졸학회지
• /
• 제9권4호
• /
• pp.261-269
• /
• 2013

The chemical mechanical polishing (CMP) process is widely used in semiconductor manufacturing process for planarization of various materials and structures. Point-of-use (POU) filters are used in most of the CMP processes in order to reduce the unwanted micro-scratches which may result in defects. The performance of the POU filter is depends on type and size of the abrasives used during cleaning process. For this reason, there is a need to evaluate POU filters for their filtration efficiency (FE) with different types of abrasives. In this study, we developed filter test system to evaluate the FE of POU using ceria and silica abrasives (slurry). The POU filter is roll type capsule filter with retention size of 0.2 ${\mu}m$. Two POU filters of different make are evaluated for FE. We observed that both POU filters show similar filtration efficiency for silica and ceria slurry. Results reveal that the ceria slurry and the colloidal silica particle are removed not only by mechanical way but also hydrodynamic and electrostatic interaction way.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 춘계학술대회 논문집 반도체재료
• /
• pp.34-37
• /
• 2001

As the integrated circuit device shrinks to smaller dimensions, chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric (IMD) layer with free-defect. However, as the inter-metal dielectrics (IMD) layer gets thinner, micro-scratches are becoming as major defects. Micro-scratches are generated by agglomerated slurry, solidified and attached slurry in pipe line of slurry supply system. To prevent agglomerated slurry particle from inflow, we installed 0.5${\mu}m$ POU (point of use) filter, which is depth-type filter and has 80% filtering efficiency for the $1.0{\mu}m$ size particle. In this paper, we studied the relationship between defect generation and pad count to understand the exact efficiency of the slurry filtration, and to find out the appropriate pad usage. Our preliminary results showed that it is impossible to prevent defect-causing particles perfectly through the depth-type filter. Thus, we suggest that it is necessary to optimize the flow rate of slurry to overcome depth type filters weak-point, and to install the high spray of de-ionized Water (DIW) with high pressure.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.1308-1311
• /
• 2004

It is very important that get polishing characteristic that to be stable that accomplish planarization of high efficiency in chemical mechanical polishing, and there is repeatability Groove of pad causes much effects in flow of slurry among various factors that influence in polishing characteristic, is expected to cause change of lubrication state and polishing characteristic in contact between wafer and pad. Therefore, divided factors of pad groove by groove pattern, groove profile, groove dimensions. This research wishes to study effect that dimension of pad groove gets in polishing performance. When changed dimension (width, depth, pitch of groove) of groove, measured change of removal rate and friction force. According as groove dimension changes, could confirm that removal rate and friction force change. While result of this experiment studies effect of pad groove in CMP, it is expected to become small help.

• 한국정보통신학회논문지
• /
• 제18권6호
• /
• pp.1401-1406
• /
• 2014

반도체소자의 제조 공정 기술 중 구리패턴을 얻기 위해서 사용하는 화학 기계적 연마(CMP)를 이용한 평탄화와 연마 공정에서 Wafer에 도포된 구리의 두께를 실시간으로 측정하여 정밀하게 제어할필요가 있는데, 이때 획득되는 센서값을 실제 두께 값으로 환산하는 계산과정에서 오차가 발생할 수 있다. 실제 측정 값에 근사한 값을 얻도록 단순평균을 이용한 방법, 이동 평균, 필터 들을 사용하여 결과를 비교하여 옹고스트롬 단위의 두께를 실시간으로 측정하는 제어 시스템의 편차를 줄이도록 하는 방법의 구현에 대해 기술한다.

• Tribology and Lubricants
• /
• 제30권3호
• /
• pp.139-145
• /
• 2014

Nowadays, most micro-patterns are manufactured during flow line production. However, a conventional rotary chemical mechanical polishing (CMP) system has a limited throughput for the fabrication of large and flexible electronics. To overcome this problem, we propose a novel linear roll-CMP system for the planarization of large-area electronics. In this paper, we present a statistical analysis on the linear roll-CMP process of copper-clad laminate (CCL) to determine the impacts of process parameters on the material removal rate (MRR) and its non-uniformity (NU). In the linear roll-CMP process, process parameters such as the slurry flow rate, roll speed, table feed rate, and down force affect the MRR and NU. To determine the polishing characteristics of roll-CMP, we use Taguchi's orthogonal array L16 (44) for the experimental design and F-values obtained by the analysis of variance (ANOVA). We investigate the signal-to-noise (S/N) ratio to identify the prominent control parameters. The "higher is better" for the MRR and "lower is better" for the NU were selected for obtaining optimum CMP performance characteristics. The experimental and statistical results indicate that the down force and roll speed mainly affect the MRR and the down force and table feed rate determine the NU in the linear roll-CMP process. However, over 186.3 N of down force deteriorates the NU because of the bending of substrate. Roll speed has little relationship to the NU and the table feed rate does not impact on the MRR. This study provides information on the design parameter of roll-CMP machine and process optimization.