• Korean Journal of Food Science and Technology
• /
• v.40 no.3
• /
• pp.283-289
• /
• 2008

This study used response surface methodology (RSM) in an effort to optimize the hot water extraction conditions of dandelion leaves in order to increase antioxidant activity in the extract. A central composite design was applied to investigate the effects of independent variables, which included the ratio of solvent to sample ($X_1$), extraction temperature ($X_2$), and extraction time ($X_3$), on dependent variables of the extracts, including soluble solid ($Y_1$), total polyphenols ($Y_2$), total flavonoid ($Y_3$), 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical scavenging ability ($Y_4$), 2,2'-azino-bis (3-ethylbenzthiazoline-6-sulfonic acid) (ABTS) radical scavenging ability ($Y_5$), and superoxide radical scavenging ability ($Y_6$). The estimated optimal conditions were as follows: $83.77{\pm}1.07^{\circ}C$ of the extraction temperature, $20.85{\pm}0.24 mL/g$ of solvent per sample, and $1.59{\pm}0.12$ hr of extraction time. At the optimal conditions, the predicted characteristic values were: a yield of 38.98%, a total polyphenol level of $74.28{\mu}g/mg$, a total flavonoid level of $74.00{\mu}g/mg$, a DPPH radical scavenging ability ($IC_{50}$) of 0.14 mg/mL, a ABTS radical scavenging ability ($IC_{50}$) of 3.24 mg/mL, and a superoxide radical scavenging ability ($IC_{50}$) of 2.49 mg/mL.

• Korean journal of food and cookery science
• /
• v.28 no.6
• /
• pp.857-863
• /
• 2012

This study prepares dried sweet pumpkins to optimize pretreatment conditions of blanching, steaming and microwave heating and to investigate the quality characteristic of each method. The sweet pumpkin blanching treatment of moisture content decreased gradually with increasing temperature, and soluble solids, and weight loss was increased. Color temperature is lower, and a higher value of L value and b value increased. As for the sweet pumpkin steaming treatment of moisture content, it was observed that the longer the steaming time was decreased, sugar content was increased. Change of color in the L value, the longer the steaming time a and b values. Also, as for the microwave treatment of the sweet pumpkin, the longer the time the moisture content decreased, it slightly increased soluble solids and weight loss. Blanching showed the lowest hardness of texture, followed by steaming, and microwaves, in order. Penetration per 20 hours per type was determined by sensory evaluation of sugar, and sugar:fructose(1:2)ratio were higher in the composition.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.35 no.4
• /
• pp.55-66
• /
• 1993

Upon freezing a soil swells due to phase change and its compression stress increase a lot. As the soil undergo thawing, however, it becomes a soft soil layer because the 'soil changes from a solid state to a plastic state. These changes are largely dependent on freezing temperature and repeated freezing-thawing cycle as well as the density of the soil and applied loading condition. This study was initiated to describe the effect of the freezing temperature and repeated freezing-thawing cycle on the unconfined compressive strength. Soil samples were collected at about 20 sites where soil structures were installed in Kangwon provincial area and necessary laboratory tests were conducted. The results could be used to help manage effectively the field structures and can be used as a basic data for designing and constructing new projects in the future. The results were as follows ; 1. Unconfined compressive strength decreased as the number of freezing and thawing cycle went up. But the strength increased as compression speed, water content and temperature decreased. The largest effect on the strength was observed at the first freezing and thawing cycle. 2. Compression strain went up with the increase of deformation speed, and was largely influenced by the number of the freezing-thawing cycle. 3. Secant modulus was responded sensitivefy to the material of the loading plates, increased with decrease of temperature down to - -10$^{\circ}$C, but was nearly constant below the temperature. Thixotropic ratio characteristic became large as compression strain got smaller and was significantly larger in the controlled soil than in the soil treated with freezing and thawing processes 4. Vertical compression strength of ice crystal(development direction) was 3 to 4 times larger than that of perpendicular to the crystal. The vertical compression strength was agreed well with Clausius-Clapeyrons equation when temperature were between 0 to 5C$^{\circ}$, but the strength below - 5$^{\circ}$C were different from the equation and showed a strong dependency on temperature and deformation speed. When the skew was less then 20 degrees, the vertical compression strength was gradually decreased but when the skew was higher than that, the strength became nearly constant. Almost all samples showed ductile failure. As considered above, strength reduction of the soil due to cyclic freezing-thawing prosses must be considered when trenching and cutting the soil to construct soil structures if the soil is likely subject to the processes. Especially, if a soil no freezing-thawing history, cares for the strength reduction must be given before any design or construction works begin. It is suggested that special design and construction techniques for the strength reduction be developed.

• Pediatric Infection and Vaccine
• /
• v.11 no.2
• /
• pp.170-175
• /
• 2004

Purpose : We experienced 7 patients with Kikuchi-Fujimoto disease(KFD) who had presented a prolonged fever and lymphadenopathy. The clinical and the laboratory aspects of the patients were analyzed. Methods : The medical records of the 7 KFD patients, who were confirmed by excisional lymph node biopsy from January 1996 through December 2003, were retrospectively analyzed. Results : The mean age of the children was $11.4{\pm}2.8$ years(ranging from 8 to 15 years). The male to female ratio was 1.3 : 1. The median duration of the fever prior to admission and the total duration of the fever were 12 days(ranging from 5 to 65 days) and 27 days(ranging 9 to 75 days), respectively. One patient had supraclavicular lymphadenopathy, 5 had cercical involvement, and 1 had axillary lymphadenopathy. All the histologic findings of the lymph nodes biopsies showed the characteristic findings consistent with KFD such as paracortical necrosis with karyorrhexis and an increase in the number of phagocytic histiocytes and atypical lymphocytes. As for the laboratory findings, leukopenia($3,800{\pm}700/mm^3$), anemia(hemoglobin, $11.0{\pm}1.2g/dL$), an elevated erythrocyte sedimentation rate($42{\pm}17mm/hr$), and a relatively low C-reactive protein level($1.3{\pm}0.9mg/dL$) were noted. Four patients received conservative therapy with antipyretics, and 3 patients were treated with prednisolone. Conclusion : KFD is a rare disease, yet should be considered in the differential diagnosis for older children with prolonged fever and lymphadenopathy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.377-377
• /
• 2012

Microprocessor technology now relies on copper for most of its electrical interconnections. Because of the high diffusivity of copper, Atomic layer deposition (ALD) $TaN_x$ is used as a diffusion barrier to prevent copper diffusion into the Si or $SiO_2$. Another problem with copper is that it has weak adhesion to most materials. Strong adhesion to copper is an essential characteristic for the new barrier layer because copper films prepared by electroplating peel off easily in the damascene process. Thus adhesion-enhancing layer of cobalt is placed between the $TaN_x$ and the copper. Because, cobalt has strong adhesion to the copper layer and possible seedless electro-plating of copper. Until now, metal film has generally been deposited by physical vapor deposition. However, one draw-back of this method is poor step coverage in applications of ultralarge-scale integration metallization technology. Metal organic chemical vapor deposition (MOCVD) is a good approach to address this problem. In addition, the MOCVD method has several advantages, such as conformal coverage, uniform deposition over large substrate areas and less substrate damage. For this reasons, cobalt films have been studied using MOCVD and various metal-organic precursors. In this study, we used $C_{12}H_{10}O_6(Co)_2$ (dicobalt hexacarbonyl tert-butylacetylene, CCTBA) as a cobalt precursor because of its high vapor pressure and volatility, a liquid state and its excellent thermal stability under normal conditions. Furthermore, the cobalt film was also deposited at various $H_2/NH_3$ gas ratio(1, 1:1,2,6,8) producing pure cobalt thin films with excellent conformality. Compared to MOCVD cobalt using $H_2$ gas as a reactant, the cobalt thin film deposited by MOCVD using $H_2$ with $NH_3$ showed a low roughness, a low resistivity, and a low carbon impurity. It was found that Co/$TaN_x$ film can achieve a low resistivity of $90{\mu}{\Omega}-cm$, a low root-mean-square roughness of 0.97 nm at a growth temperature of $150^{\circ}C$ and a low carbon impurity of 4~6% carbon concentration.

• Journal of Conservation Science
• /
• v.25 no.3
• /
• pp.299-316
• /
• 2009

The Goryeo roof tiles from the Oegol site in Tangjeong, Asan are classified into three groups in color such as gray, red yellow and gray-yellow groups, respectively. While each group of tiles shows characteristic specific gravity, absorption ratio, LOI and vitrification degree, mineral content and distribution, and chemical composition are generally homogeneous among all groups of roof tiles. Also, all roof tiles and soils from the site show similar geochemical behavior of elements and clay-mineralization degree. This indicates that the soil from the site is probable to be a raw material of the roof tiles. Firing temperature of the roof tiles is estimated as 950 to $1,050^{\circ}C$ for the gray group, 800 to $900^{\circ}C$ for the red yellow group, and 900 to $950^{\circ}C$ for the gray-yellow group. In conclusion, roof tiles from the Oegol site is interpreted to be made of local clay without additive minerals, applying various firing conditions and standardized purifying process of raw clay materials.

• Journal of Conservation Science
• /
• v.29 no.4
• /
• pp.333-343
• /
• 2013

The exhibition hall of museum has been damaged by abundant dust and mold of the air in the room. Occurrence of microorganisms on the surface of the cultural heritage will cause damages such as coloration, materials degradation, deterioration, etc. In this study, we investigated the temperature/humidity and microbes distribution in exhibition hall, display showcase, and on surface of wall paintings in the Muwisa museum. From some samples collected in exhibition hall and display showcase, we identified so many varieties of micro-organisms such as Aspergillus sp., Penicillium sp., Cladosporium sp.. In particular, we could see a large number of microorganisms in the number 1, 2 exhibition hall compared with the number 3 exhibition hall. The results examining the distribution of the temperature and humidity were showed as $28{\pm}4^{\circ}C$ and 70~80%, respectively. The number 1 exhibition showcase was higher humidity environment than the number 2, 3 exhibition hall compared to the distribution ratio, which considered as correlation with the distribution of microorganism concentration. As these results, we understood that high temperature and humidity in the exhibition hall and display showcase of the Muwisa museum were characteristics caused by environmental management and hermetically-sealed rooms.

• Economic and Environmental Geology
• /
• v.25 no.1
• /
• pp.27-39
• /
• 1992

Several pyrophyllite deposits occur around the Milyang area where Cretaceous andesitic rocks and spatially related granitic rocks are widely distributed. Pyrophyllite ores consist mainly of pyrophyllite, and quartz with small amount of sericite, pyrite, dumortierite, and diaspore. The andesitic rocks and spatially related granitic rocks in this area suggest that they could be formed from the same series of a calc-alkaline magma series. The contents of $SiO_2$, $Al_2O_3$, LOI(loss on ignition) are enriched, and $K_2O$, $Na_2O$, CaO, MgO, $Fe_2O_3$ are depleted in altered andesitic rocks and ores. Enrichment of As, Cr, Sr, V, Sb and depletion of Ba, Cs, Ni, Rb, U, Y, Co, Sc, Zn are characteristic during mineralization. The pyrophyllite ores can be discriminated from the altered-and unaltered wall-rocks by an increasing of $(La/Lu)_{cn}$ from 4.18~22.13 to 8.98~55.05. In R-mode cluster analysis, Yb-Lu-Y, La-Ce-Hf-Th-U-Zr, $TiO_2-V-Al_2O_3$, Sm-Eu, $CaO-Na_2O-MnO$, Cu-Zn-Ag, $K_2O-Rb$ are closely correlated. In the discriminant analysis of multi-element data, $P_2O_5$, As, Cr and $Fe_2O_3$, Sr are helpful to identify the ores from the unaltered-and altered wall-rocks. In the factor analysis, the factors of alteration of andesitic rocks and ore mineralization were extracted. In the change of ions per unit volume, $SiO_2$, $Al^{3+}$ and LOI are enriched and $Na^+$, $K^+$, $Ca^{2+}$, $Mg^{2+}$, $Mn^{2+}$ and $Fe^{3+}$ are depleted during the alteration processes. The Milyang and the Sungjin pyrophyllite deposits could be mineralized by hydrothermal alteration in a geochemical condition of low activity ratio of alkaline ions to hydrogen ion with reference to spatially related granitic rocks.

• Journal of Korean society of Dental Hygiene
• /
• v.10 no.6
• /
• pp.1129-1139
• /
• 2010

Objectives : The purpose of this study was to examine the toothbrushing practice behavior of preschool children by observing children's actual toothbrushing behavior and further to offer basic data available for being reflected in direction and goal establishment of the systematic and organized oral health education in consideration of individual characteristic. Methods : It targeted 225 preschool children from May 6, 2010 to June 8, and analyzed by having the survey results of totally 208 people, except 17 who are noncooperative with the observation survey. As for the collected materials, it carried out frequency analysis and $x^2$-test in order to grasp subjects' general characteristics and toothbrushing practice behaviors and to examine correlation, by using SPSS 12.0 for window. Results : 1. A grasp of toothbrush was indicated 47.1% for "proper" and 52.9% for "improper." The position of holding a toothbrush was indicated to be the highest with 59.6% for "the center in grip." 2. Toothpaste amount was indicated to be 49.0% for" tip in toothbrush, "followed by 38.9% for "half in toothbrush" and 12% for "every side of toothbrush" in order. Significant difference was shown according to age($x^2$=19.125. p<.05). 3. Average toothbrushing time per once was surveyed to be $106{\pm}56$ seconds. 4. As for a toothbrushing method by region, the labial and the baccal surface were indicated to be horizontal scrub with 63% and fones method 11.5%. Significant difference was shown according to gender($x^2$=10.275. p<.05). The anterior lingual surface wasn't washed with 72.6%. Significant difference was shown according to appearance of education($x^2$=6.056. p<.05). 5. A case of requiring exchange because of being widened toothbrush was indicated to be 59.2%. The toothbrush replacement in the highest ratio was needed in kindergarten teachers. Conclusions : The actual toothbrushing practice attitude of preschool children was surveyed to be not right as a whole such as toothbrushing time, toothbrushing method, toothpaste amount, and replacement of toothbrush. Accordingly, the oral health education will need to be performed in order for a change into positive attitude and for improvement in practice level. In addition, it is considered to be likely necessary for development in substantial oral health educational program available for enhancing knowledge level of oral health care in mothers and kindergarten teachers.

• Journal of the Society of Disaster Information
• /
• v.10 no.1
• /
• pp.71-83
• /
• 2014

This study carried out an experiment in order to compare thermal characteristics after collecting dust generated in the process of disposing of waste tire, plywood flour in the process of manufacturing plywood, salicylic acid dust in the process of manufacturing functional soap, and dust in the process of manufacturing wheat powder, which has potential fire and explosion hazard. According to the results of experiment, the analysis showed that all samples subject to the experiment were in the condition where heat flux decreased and temperature decreased as the quantity of added talc was increased. This shows that decomposition rate decreased, and hazard decreased. However, in all of samples subject to the experiment, as heating rate increased, endothermic onset temperature moved to the low-temperature part, and the amount of absorbed heat was largely increased. This showed that the decomposition hazard of sample increased as heating rate increased, according to the analysis. Besides, TGA experiment results showed that thermal stability was secured because total weight loss decreased as the amount of talc was increased for all samples subject to the experiment regarding the ratio of weight loss. It is expected that the continuous research and supplementation of dust explosion mechanism in the future will contribute to the establishment of measures for the effective dust explosion prevention.