• Proceedings of the KWS Conference
• /
• 2001.05a
• /
• pp.224-227
• /
• 2001

In this study, CT specimens were prepared hem ASTM SA516 which was used for pressure vessel plates for room and low temperature service. And we got the following characteristics from fatigue crack growth test carried out in the environment of room and low temperature at $25^{\circ}C$, -3$0^{\circ}C$, -6$0^{\circ}C$, -8$0^{\circ}C$, -l$0^{\circ}C$ and -l2$0^{\circ}C$ and in the range of stress ratio of 0.1, 0.3 by means of opening mode displacement. At the constant stress ratio, the threshold stress intensity factor range $\Delta K_{th}$ in the early stage of fatigue crack growth ( Region I ) and stress intensity factor range $\Delta$K in the stable of fatigue crack growth ( Region II) was increased in proportion to descend temperature. It assumed that the fatigue resistance characteristics and fracture strength at low temperature is considerable higher than that of room temperature in the early stage and stable of fatigue crack growth region. The straight line slope relation of logarithm da/dN - $\Delta$K in Region II, that is, the fatigue crack growth exponent m increased with descending temperature at the constant stress ratio. It assumed that the fatigue crack growth rate da/dN is rapid in proportion to descend temperature in Region H and the cryogenic-brittleness greatly affect a material with decreasing temperature.

• Journal of Korea Society of Industrial Information Systems
• /
• v.21 no.1
• /
• pp.43-50
• /
• 2016

In this paper, new automatic LC calibrator is proposed for realizing a passive LC filter with almost constant frequency characteristic regardless of the PVT variations. The SAW-less GPS RX front-end is implemented using a 65nm CMOS process using the proposed LC calibrator. Also, new dual-mode low noise amplifier (LNA) structure is proposed to generate the RF signal required for the LC calibrator. The characteristics of the implemented GPS RX front-end show the voltage gain of about 42.5 dB, noise figure of below 1.35 dB, the blocker input P1dB of -24 dBm in case of the worst blocker signal at 1710 MHz frequency, while it consumes 7 mA current at 1.2 V power supply voltage.

• Journal of Korean Society for Geospatial Information Science
• /
• v.3 no.2 s.6
• /
• pp.131-136
• /
• 1995

In this paper, We explain the development of helicopter avation information system which provides the current location and other pre-saved informations in order to guarantee the safe aviation. The system we developed has the functions such as displaying digital map data and current location, route planning, displaying the rate of deviation, calculating and displaying the cross sectional view through the route and providing a real-time speed, heading and other informations. In this system, we use GPS to get the current location, made the 1:250,000 digital map to display the current location and made the cross sectional view from the DEM(Digital Elevation Mode)) data to help safe aviation. This system provides many kinds of route setting methods by using UTM coordinates, Lati. Longi, coordinates, database of heliport location, scanned map, etc., and displaying the heading and distance. Moreover, it also has a characteristic of providing a consistent user interface.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.905-910
• /
• 2003

One of the methods that are used to compare and verify the supporting performance of the spacer grids developed is the vibration characteristic test. A modal test in this paper is performed for a dummy rod 3,847mm tall supported by eight New Doublet (ND) spacer grids. For the vibration test in air, nine accelerometers, one displacement sensor and one shaker are used for acquiring signals, and an I-DEAS TDAS software is employed for analyzing the signals. Also, a finite element (FE) analysis is performed by a beam-spring simple model and a contact model simulating the contact phenomenon between the rod and the fm spring. And then, the result of the FE analysis is compared with that of the modal test. The natural frequencies as well as the mode shapes calculated by the proposed contact models have a greater similarity to the test results than those by the previous beam-spring model. In addition, for grasping whether or not the modal parameters are influenced by where shaking spot is, two kinds of tests are performed; one is for the shaker attached at the fourth span (center), the other is for the shaker at the fifth span that is one span nearer to the bottom of the rod. The latter shows higher MAC than the former. Finally, the vibration displacements are measured in the range of 0.112-0.214mm for the excitation force of 0.25-0.75 N.

• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.3
• /
• pp.37-41
• /
• 2002

In this research, we investigate the properties of membrane and thin film sensor which is using magnetic resonance properties. we expect to $Si_xN_y$ and SiC materials as membrane materials, we measured thin film stress and properties to find the best membrane fabrication condition. Of the two membrane, $Si_xN_y$ thin film is the better than SiC thin film. because of an adequate tensile stress and lower thermal expansion coefficient as sensor structure layer. After performing deposition and patterning thin film sensor material on $Si_xN_y$, we analyzed the magnetic hysteresis and magnetic resonance frequency of sensor. If the magnetic field which is applied in sensor material is removed, magnetization made by magnetic field is transited to elastic mode. moreover. energy radiation is induced during the transition and voltage generates in sensor by energy radiation. At this moment, If voltage generation period is longer, mechanical vibration is induced and signal is generated by mechanical vibration. we also see that as the increase of thin film sensor' length and width, magnetic resonance frequency is decreased.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.12
• /
• pp.1-9
• /
• 2000

A new method, the external resistance method (ERM method), is proposed for accurate extraction of the gate bias-dependent effective channel carrier mobility (${\mu}_{eff}$) and separated parasitic source/drain resistances ($R_S$ and $R_D$) of n-channel MOSFET's. The proposed ERM method is applied to n-channel LDD MOSFETs with two different gate lengths ($W_m/L_m=30{\mu}m/0.6{\mu}m,\;30{\mu}m/1{\mu}m$) in the linear mode of current-voltage characteristics ($I_D-V_{GS},\;V_{DS}$). We also considered gate voltage dependence of separated $R_2$ and $R_D$ in the accurate modeling and extraction of effective channel carrier mobility. Good agreement of experimental data is observed in submicron n-channel LDD MOSFETs. Combining with capacitance-voltage characteristics, the ERM method is expected to be very useful for accurate and efficient extraction of ${\mu}_{eff},\;R_D,\;R_S$, and other characteristic parameters in both symmetric and asymmetric structure MOSFET's in which parasitic resistances are critical to the improvement of high speed performance and reliability.

• Journal of the Korean Society of Safety
• /
• v.33 no.4
• /
• pp.1-7
• /
• 2018

This paper is analyzed for the thermal characteristics(1 year) of the 6 components(DC breaker, DC filter(including capacitor and discharge resistance), IGBT(Insulated gate bipolar mode transistor), AC filter, AC breaker, etc.) of a photovoltaic power generation-based PCS(Power conditioning system) below 20 kW. Among the modules, the discharge resistance included in the DC filter indicated the highest heat at $125^{\circ}C$, and such heat resulting from the discharge resistance had an influence on the IGBT installed on the rear side the board. Therefore, risk priority through risk priority number(RPN) of FMEA(Failure modes and effects analysis) sheet is conducted for classification into top 10 %. According to thermal characteristics and FMEA, it is necessary to pay attention to not only the in-house defects found in the IGBT, but also the conductive heat caused by the discharge resistance. Since it is possible that animal, dust and others can be accumulated within the PCS, it is possible that the heat resulting from the discharge resistance may cause fire. Accordingly, there are two options that can be used: installing a heat sink while designing the discharge resistance, and designing the discharge resistance in a structure capable of avoiding heat conduction through setting a separation distance between discharge resistance and IGBT. This data can be used as the data for conducting a comparative analysis of abnormal signals in the process of developing a safety device for solar electricity-based photovoltaic power generation systems, as the data for examining the fire accidents caused by each module, and as the field data for setting component management priorities.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.261-265
• /
• 2005

This paper describes the DC-DC Converter for Ancillary Power Supply in Hybrid Electric Vehicle. DC-DC Converter is used for charging 12V auxiliary battery supplying electric power to head ramp, audio, ECU etc in automobiles. used DC-DC Converter Topology is PS-ZVS FB(Phase Shifted Zero Voltage Switching Full-Bridge) to reduce switching loss and EMI noise induced by high frequency operating condition. And For easy compensation and stable system response characteristic, current mode control method including slope compensation is employed. Constant current / constant voltage charging control method guarantee stable electric charging of auxiliary battery. Simulation toll PSIM6.0 is used for initial circuit parameter settings and H/W debuging. Thermal problems of Switching components in DC-DC Converter is improved by using Thermo Tracer.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.6
• /
• pp.501-508
• /
• 2014

In this paper, a method on deducing the capacity spectrum based on nonlinear earthquake response analysis will be introduced. Damage assessment of general building draws the capacity spectrum through the Push-over analysis and the intersection point of capacity spectrum and demand spectrum is seen as performance point. Push-over analysis is the way to perform static analysis by using the equivalent static load changed from the effect of earthquake and predict the behavior of structures by earthquake. But, this method can not be taken into account in the effects of higher mode and the dynamic characteristic. Therefore, in order to calculate the capacity spectrum under dynamic properties of building. A capacity spectrum from going ahead with the nonlinear earthquake response analysis is suggested.

• Transactions of the KSME C: Technology and Education
• /
• v.3 no.1
• /
• pp.15-21
• /
• 2015

In this paper a prediction method of GHP performance is proposed for increasing design accuracy. Two compressors with different capacity and 2311cc gas engine are used for prediction and the target capacity of GHP is 25HP. For predicting GHP performance at first the operation points are randomly selected and then as compared with compressor performance date and heat exchanger characteristic, more accurate operating points are decided through recursive calculation. Lastly engine performance date is used for calculating gas consumption volume. Predicting heating mode performance of GHP, evaporator is separated to the two section of absorbing heat in outdoor air and in engine. From the experimental results, it was found that the simulation model is good for the predicting GHP efficiency and the difference of predicted and measured efficiency is less than 5%.