• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.9
• /
• pp.93-99
• /
• 1998

A novel four-channel narrowband wavelength demultiplexer using integrated four vertical directional coupler structures is proposed and theoretically investigated. Four ridge waveguide with different ridge width are vertically coupled to a strip-loaded waveguide which results four different wavelengths filtered out to each ridge waveguide. In order to reduce the side-lobes, the coupling coefficients are varied along the propagation direction. The spectral responses of channels were found to be quite uniform. An average channel spacing of 7 nm with power coupling efficiency of ~90%, 3-dB passband width of 2 nm, and 20 dB side-lobe suppression ratio was achieved.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.3
• /
• pp.56-62
• /
• 1998

One of the key components to accomplish WDM all-optical network is an arrayed waveguide grating router. The spectral characterisitc of the ypeical arrayed waveguide grating rouger has parabolic shape, hence the bandwidth is limited. The spectral response of an optical filter should be as flat as possible for the reliable operation of the syste, because the center frequency of the optical source could be deviated in the actual system. In order to acquire these characteristics, we propose and design a new type of the arrayed waveguide grating router with a flat passband using the Fourier optics concept. The BPM simulation results of the new arrayed waveguide grating router with the flat passband show that the bandwideth is 0.8 nm at -1 dB, instertion loss about 6 dB, and the crosstalk less than -23 dB fro each cnannel, which is 1.6 nm(200 GHz) separated from the adjacent channel around 1550 nm wavelength range.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.101-104
• /
• 1998

We report some methods for measuring a LiNbO$_3$ optical phase modulator bandwidth. Since Mach-Zehnder waveguide type, one of methods for modulation bandwidth measurement, is comparatively simple and useful, it was adapted in this work. In order to confirm this method, the waveguide of single and Mach-Zehnder type were fabricated on the same wafer. The Mach-Zehnder interferometric waveguide and the single channel waveguide were used for the measurement of the phase modulator's driving voltage and bandwidth for device fabrications, respectively. Ti-860$\AA$ in-diffusion was achieved in a wet-bubbling oxygen environment at 105$0^{\circ}C$/8hours. LINbO$_3$ internal chips were pigtailed to PMF(polarization maintaining fiber)/SMF(single mode fiber) using an epoxy curing technique. Examined were optical properties such as an insertion loss, propagation loss and mode size, and the loss mechanism of optical coupling between an optical fiber and a waveguide was considered.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.3
• /
• pp.557-562
• /
• 2017

In this paper, we show the design of a rotary joint transition for the X-band channel in a rotatable microwave communication system. The transition seems complicated to make a channel between two coaxial cables through a cylindrical waveguide. To make a broad-band performance in the X-band with low insertion loss and return loss given the constraint on the length and radius of this complicated-looking cylindrical structure, Genetic Algorithm optimization is adopted to check the validity of an intensive parametric study in the design. The structure is fabricated and tested to show how valid the design method is as well as good frequency responses.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.9
• /
• pp.634-642
• /
• 2001

We calculate the facet reflectivity of buried channel waveguides and ridge waveguides as a function of the waveguide width for various thicknesses using the angular spectrum method and the two dimensional field profiles obtained by the variational method (VM) and the effective index method (EIM). The variation of the reflectivity of buried channel waveguides as a function of the waveguide width is large, while that of ridge waveguides is very small. The accuracy of the field profiles necessary for the calculation of the facet reflectivity using the angular spectrum method greatly affects that of the facet reflectivity. The difference between the exact reflectivity and that using EIM increases as the waveguide width and thickness decreases due to the inaccuracy of the field profiles obtained by EIM. However, the difference between the exact reflectivity and that using VM is smaller than that using EIM regardless of waveguide width and thickness. The difference between the facet reflectivities u sing EIM and VM is small in the area where the EIM works very well.

• Proceedings of the Optical Society of Korea Conference
• /
• 2008.07a
• /
• pp.143-144
• /
• 2008

• Journal of the Optical Society of Korea
• /
• v.10 no.4
• /
• pp.169-173
• /
• 2006

This paper describes an efficient optimal design method for an arrayed waveguide grating (AWG) having MMI coupler with flattened transfer function. The objective function is the norm of the difference between calculated and target spectra. To analyze the AWG transfer function, the Fresnel-Kirchhof diffraction formula was employed and the design variable was optical path difference of each array waveguide. The (1+1) Evolution Strategy was applied to an eight-channel coarse wavelength division multiplexing (CWDM) AWG as the optimization tool. For obtaining a broadened spectrum, we use a MMI coupler and the variation in optical path difference at each array waveguide changes the shape of the transfer function to obtain the optimal spectrum shape.

• Macromolecular Research
• /
• v.12 no.5
• /
• pp.437-442
• /
• 2004

We have fabricated a polymeric waveguide by using a hot embossing technique and have investigated its propagation loss. The replication of waveguide channels through the use of a hot embossing technique is of interest as a single-step process that could deliver surface roughnesses far smaller than the wavelength. We have evaluated experimentally that the sidewall roughness has a dominant effect on insertion losses of the multimode polymeric waveguide. The propagation loss of the waveguide decreased dramatically upon decreasing the sidewall roughness of the channel. We have confirmed that the preparation of waveguides having nanometer-scale sidewall roughness and 0.1 dB/cm propagation loss is possible when using the hot embossing technique.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.5
• /
• pp.400-406
• /
• 1998

We investigated the preparation and guided-mode properties of $Ti:LiNbO_3$ waveguides which were fabricated by Ti in-diffusion. The diffusion method to reduce the Li out-diffusion was proposed. The optical guided-mode and propagation loss based on butt-coupling pigtailed with PMF-input were measured. How to improve the polishing grade of waveguide endfaces is newly proposed in this paper. To show the mode propagations, the BPM simulations of channel waveguide are described.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.6
• /
• pp.83-88
• /
• 2017

In this paper, a 3-port waveguide circulator of Ka-band millimeter-wave for isolation between transmit channel and receive channel at high power transmit mode is designed and fabricated for the seeker of the guided missile and circulator performance is verified through the S-parameter, high power and operation temperature test. At the configuration design, interface design between a seeker antenna and the circulator is considered and half-height of standard waveguide is applied for minimum and light weight body. The shape of permanent magnet and ferrite is optimized by simulation and tuning dielectrics at each port are placed for the best performance. In Fc(center frequency)${\pm}1000MHz$, designed waveguide circulator has below -20 dB return loss, below 0.5 dB insertion loss and below -23 dB isolation. It is found that circulator characteristics is similar to design results.