• ETRI Journal
• /
• v.26 no.5
• /
• pp.486-492
• /
• 2004

The emergence of wide channel bandwidth wireless standards requires the use of a highly linear, wideband integrated CMOS baseband chain with moderate power consumption. In this paper, we present the design of highly linear, wideband active RC filters and a digitally programmable variable gain amplifier. To achieve a high unity gain bandwidth product with moderate power consumption, the feed-forward compensation technique is applied for the design of wideband active RC filters. Measured results from a $0.5{\mu}m$ CMOS prototype baseband chain show a cutoff frequency of 10 MHz, a variable gain range of 33 dB, an in-band IIP3 of 13 dBV, and an input referred noise of 114 ${\mu}Vrms$ while dissipating 20 mW from a 3 V supply.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.10
• /
• pp.951-963
• /
• 1991

In this paper M-ary Psk system for digital land mobile radio utilized the raised-cosine filter instead of LPF with rectangular frequency characteristic as luniting channel bandwidth are implemented to measure their performance and effect of ISI and jitter. Also the error probability is calcylated on the condition of fast Rayleihg fading, cochannel interference and AWGN, It is found that QPSK and 8-PSK system with 2-branch diversity, can be improved by 3 or 5 time of spectral effciency respectively, comparinng with one of the non diversity QPSK and 8.PSK system.

• Journal of Communications and Networks
• /
• v.4 no.3
• /
• pp.176-188
• /
• 2002

This paper presents results of continuous wave and swept frequency response measurements over the frequency range of UNII lower and middle bands from 5.15GHz to 5.35GHz in indoor environments. From the continuous wave measurements at 5.2GHz, the excess path loss, and the statistical characteristics of the temporal and spatial fading were found. By sweeping the frequency over the band, envelope correlation as a function of frequency was found and the coherence bandwidth (CBW) was determined from the envelope correlation. Using a channel model, the CBW was used to evaluate RMS delay spread. The dependence of CBW on the antenna polarization was simulated and compared with the measurement results. The influence of room size and separation of transmitter and receiver for LOS paths on RMS delay spread was discussed.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.5
• /
• pp.591-596
• /
• 1986

A binary continuous phase frequency shift keying (CPFSK), whose phase is a continuous function of time and instantaneous frequency is constant, is a bandwidth efficient constant envelope signalling scheme. A transmitting signal is formed by combined coding of a convolutional encoder and a binary CPFSK modulator. The signal is transmitted throuth additive white Gaussian noise(AWGN) channel. If the received signal is detected by a coherent maximum likelihood(ML) receiver, error probability can be expressed approximately in terms of minimum Euclidean distance. We propose rate 2/4 codes for the improvement of error performance without increating the data rate per bandwidth and the receiver complexity. Its minimum Euclidean distances are compared with those of rate \ulcornercodes as a function of modulation index and observation interval.

• Journal of Broadcast Engineering
• /
• v.12 no.3
• /
• pp.222-229
• /
• 2007

According to the advancement of multimedia compression technologies, high quality multi-media services are easily found in common life. Along with this situation, 5.1-channel audio service also has expanded the application area to home theater system and car theater system and consumer can easily take a chance to experience the feeling of 5.1-channel audio. On the other hand, terrestrial DMB service has been launched in Korea from Dec. 2005 as a handhold multi-media broadcasting service. However, multi-channel audio was not considered due to the insufficiency of bandwidth and the handhold usage. Lately, MPEG is standardizing high efficiency multi-channel audio compression technology for handheld broadcasting service, and several trial for application is introduced in Europe. In this paper, we would like to explain multi-channel audio compression technology, describe the implementation of the verification system for the multi-channel audio service over T-DMB and investigate the possibility of further realization of the service.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.5
• /
• pp.249-258
• /
• 2013

In multi-hop ad hoc networks, multi-interface multi-channel architecture is being noticing as methodology to improve the effective bandwidth and end-to-end throughput, But since existing routing metrics designed for networks based on single-interface exactly can not reflects the nature of networks based on multi-interface multi-channel, we are not expected the effect of throughput improvement. there had been proposal of MCR that discover high throughput by using metrics such as channel diversity and interface switching cost. however, MCR have an problem that is degraded it's performance in congested networks, because it not reflects the impact of traffic load. in this paper, we propose MAMCR metric, which select high throughput paths under congested conditions by combination MCR with channel access time metric, and conform it's the effect of performance improvement by ns-2 simulation.

• ETRI Journal
• /
• v.40 no.1
• /
• pp.39-50
• /
• 2018

More people prefer using rail traffic for travel or for commuting owing to its convenience and flexibility. The railway scenario has become an important communication scenario in the fifth generation era. The communication system should be designed to support high-data-rate demands with seamless connectivity at a high mobility. In this paper, the channel characteristics are studied and modeled for the railway tunnel scenario with straight and curved route shapes. On the basis of measurements using the "Mobile Hotspot Network" system, a three-dimensional ray tracer (RT) is calibrated and validated for the target scenarios. More channel characteristics are explored via RT simulations at 25.25 GHz with a 500-MHz bandwidth. The key channel parameters are extracted, provided, and incorporated into a 3rd-Generation-Partnership-Project-like stochastic channel generator. The necessary channel information can be practically realized, which can support the link-level and system-level design of the communication system in similar scenarios.

• Journal of Satellite, Information and Communications
• /
• v.5 no.1
• /
• pp.32-37
• /
• 2010

The algorithm of multiple channel signal processing requires the flexibility of variable frequency band, efficient allocation of transmission power, and flexible frequency band reallocation to satisfy various service types which requires different transmission rates and frequency band. There are three methods including per-channel approach, multiple tree approach, and block approach performing frequency band reallocation method by channelization and dechannelization in the multiple-channel signal. This paper proposes an improved per-channel approach for converting the frequency band of multiple carrier signals efficiently. The proposed algorithm performs decimation and interpolation using CIC(cascaded integrator comb filter), half-band filter, and FIR filter. In addition, it performs filtering of each sub-channel, and reallocates channel band through FIR low-pass filter in the multiple-channel signal. The computer simulation result shows that the perfect reconstruction of output signal and the flexible frequency band reallocation is performed efficiently by the proposed algorithm.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.139-142
• /
• 2009

RFID(Radio Frequency IDentification) technology is an automatic identification method using radio frequencies between RFID reader which collects the information and tag which transmits the information. RFID technology develops passive RFID which transmit the only ID to active RFID which transmit the additional information such as sensing information. However, ISO/IEC 18000-7 as active RFID standard has a problem which cannot use multiple channel. To solve this problem, we use the 2.4GHz bandwidth technology and we propose the dynamic channel allocation method which can efficiently allot a channel. we show the operation of the dynamic channel allocation method through design and implement with CC2500DK of Taxas Instrument.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.1
• /
• pp.122-130
• /
• 2015

This paper presents a 6 Gb/s 4-channel arrayed transimpedance amplifiers (TIA) with the gain control for 4-channel passive optical network in $0.13{\mu}m$ complementary metal oxide semiconductor (CMOS) technology. A regulated cascode input stage and inductive-series peaking are proposed in order to increase the bandwidth. Also, a variable gain control is implemented to provide flexibility to the overall system. The TIA has a maximum $98.1dB{\Omega}$ gain and an input current noise level of about 37.8 pA/Hz. The die area of the fabricated TIA is $1.9mm{\times}2.2mm$ for 4-channel. The power dissipation is 47.64 mW/1ch.