• 분석과학
• /
• 제14권6호
• /
• pp.494-498
• /
• 2001

크로메이트를 대체하기 위한 새로운 표면처리 화합물로서 cerium nitrate를 사용하고 Al도금강판에 적용하였을 때, 그 표면의 특성을 정밀하게 분석하였다. 그 결과, cerium nitrate로 처리된 Al도금강판의 표면층에서 cerium은 (+4) 산화 상태와 (+3) 산화 상태의 혼합된 형태로 존재하며 각각의 상대적 비율은 57 % 및 43 %인 것으로 나타났다. 이러한 cerium 화합물의 피막은 Al도금층의 자연산화막과 더불어 도금강판의 표면에 보호 피막을 형성하여 Al도금강판의 표면 부식을 방지하게 된다.

• 한국산업융합학회 논문집
• /
• 제5권4호
• /
• pp.385-390
• /
• 2002

An efficient synthesis of spiroannulated dihydrofurans is achieved from 1,3-dicarbonyl compounds and exocyclic alkenes in the presence of cerium ammonium nitrate(IV) in moderate yields. In the case of entries 3-9, as a single product was seen. Especially, reaction of 15 with methylenecyclohexane afforded the two regioisomeric cyclo adducts 21 and 22. The structures of these adducts were confirmed by IR and NMR-Spectra.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.70-70
• /
• 2010

Cerium oxide nanofibers have been of great interest in fundamental level study. We fabricated polyvinylpyrollidone (PVP) and cerium nitrate nanofibers composite applying a mixed solution of PVP and cerium nitrate hydrate (Ce(NO3)3) with various cerium concentration from 8.87 to 35.5wt% by electrospinning process. Electrospinning method is a simple and cost-effective process to make nanoand submicro nanofiber fabrication. We applied 0.69 kV/cm of electric field between the capillary and a drum collector covered with aluminum foil. Cerium oxide nanofibers were obtained after calcination of PVP/Ce(NO3)3 nanofibers composite at 573, 873 and 1273K, which were chosen by thermal gravimetry analysis. The obtained nanofibers were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS). When the viscosity of the electrospinning solution was high named over 60 cP, only nano and submicro-sized cerium oxide fibers were collected. X-ray photoelectron spectroscopy (XPS) was performed for investigation of the chemical nature of the obtained ceria nanofibers. After we calcined the PVP/ceria nanocomposites, metallic cerium was oxidized to cerium oxide including ceria.

• 한국재료학회지
• /
• 제24권1호
• /
• pp.33-36
• /
• 2014

This study was aimed at synthesizing and characterizing cerium-doped titania. Cerium-doped anatase titania powders were prepared by sol-gel process, with ammonium (IV) nitrate and titanium (IV) butoxide as the raw materials. The characteristics of pure $TiO_2$ and cerium-doped $TiO_2$ were investigated by XRD, TG/DTA, FE-SEM, and UV-vis spectroscopy. The results of this study show that anatase type of $TiO_2$ was obtained in as-prepared and calcined $TiO_2$ and Ce-$TiO_2$ powder. A DTA curve was also observed as the crystallization temperature decreased with increasing cerium contents. We found that the crystallite size of the obtained anatase particles decreased from 55 nm to 25 nm and the particle size decreased with increasing cerium contents. Moreover, UV-vis spectra showed that anatase titania powders with various cerium contents effectively extend the light absorption properties to the visible region.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 추계학술대회 논문집
• /
• pp.268-268
• /
• 2015

The corrosion protection behavior of AZ31 magnesium alloy (Mg alloy) with cathodic electrophoretic coating (E-coating) pretreated by cerium-based conversion coatings at various pH was investigated in this study. Cerium-based conversion coatings (CeCCs) were deposited on AZ31 Mg alloy by immersion treatment in the nitrate-based cerium salt solution. The morphology and composition of the CeCCs were analyzed using scanning electron microscopy and energy dispersive X-ray spectroscopy. The corrosion properties of the AZ31 Mg alloy pretreated with cerium coating and subsequently E-coated were studied during salt-spray testing. The surface morphologies of the E-coated Mg alloy were examined in detail after different testing times using digital photography. It was found that the protective properties of the E-coating on AZ31 Mg alloy generated are heavily dependent upon the CeCC factors such as treatment time, coating thickness and pH of the solution.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 춘계학술발표회 논문집
• /
• pp.257-257
• /
• 2012

Cerium doped anatase titania powders were prepared by sol-gel process, with ammonium (IV) nitrate and Titanium (IV) butoxide as the raw materials. The characteristics of anatase $TiO_2$ and cerium doped $TiO_2$ were investigated by XRD, DTA, FE-SEM and UV/Vis spectroscopy. Research results indicated that XRD data characteristic diffraction peaks of anatase phase and also showed that cerium phase was not observed. Moreover XRD and DTA results imply that the addition of cerium to titania modifies the mechanism of formation of the titania phases.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2010년도 추계학술발표논문집 1부
• /
• pp.318-322
• /
• 2010

NaZSM 5 was synthesized in an alkaline medium and impregnated with cerium oxide by wet method using cerium nitrate as the source for cerium. There TGA results shows decomposition of nitrate at $200^{\circ}C$. The ceria impregnated ZSM 5 materials were designated as NaZSM 5 (X) where X is the percent ceria impregnated (3, 5, 7, 11, 19%). They were characterized by XRD, SEM, EDAX, BET techniques. XRD analysis showed decrease in intensity of the patterns with the increase in the ceria loading but crystallization of ceria to larger size is evident for 11 and 19% loading. The surface area and pore volume decreased with increase in ceria loading. The maximum adsorption capacity of NaZSM 5 (5%) is 100.2 mg/g of sorbent. The ceria impregnated NaZSM 5's were found to be regenerable, selective and recyclable.

• 한국분말재료학회지
• /
• 제13권3호
• /
• pp.192-198
• /
• 2006

The nanostructured cerium oxide powders were synthesized by spray thermal decomposition process for the use as the raw materials of resistive oxygen sensor. The synthesis routes consisted of 1) spray drying of water based organic solution made from cerium nitrate hydrate ($Ce(NO_3){_3}6H_2O$) and 2) heat treatment of spray dried precursor powders at $400^{\circ}C$ in air atmosphere to remove the volatile components and identically to oxidize the cerium component. The produced powders have shown the loose structure agglomerated with extremely fine cerium oxide particles with about 15 nm and very high specific surface area ($110m^2/g$). The oxygen sensitivity, n ($Log{\propto}Log (P_{O2}/P^o)^{-n}$ and the response time, $t_{90}$ measured at $600^{\circ}C$ in the sample sintered at $1000^{\circ}C$, were about 0.25 and 3 seconds, respectively, which had much higher performances than those known in micron or $100{\sim}200nm$ sized sensors.

• Bulletin of the Korean Chemical Society
• /
• 제34권10호
• /
• pp.3059-3064
• /
• 2013

In this study transesterification of Triglycerides (TG) from Jatropha curcas oil (JCO) with methanol for production of biodiesel was investigated over cerium impregnated ZSM-5 catalysts. NaZSM-5 was synthesized in an alkaline medium and impregnated with cerium oxide by wet method using cerium nitrate as a source for cerium. They were characterized by X-ray diffraction (XRD), Thermogravimeteric analysis (TGA), $CO_2$-temperature programmed desorption, and $N_2$ adsorption/desorption analysis. XRD analysis showed decrease in intensity of the patterns with the increase in the ceria loading but crystallization of ceria to larger size is an evident for 10 and 15% loading. The optimal yield of transesterification process was found to be 90% under the following conditions: oil to methanol molar ratio: 1:12; temperature: $60^{\circ}C$; time: 1 h; catalyst: 5 wt %. Here the yield of fatty acid methyl ester (FAME) was calculated through $^1H$ NMR analysis. The investigation on catalyst loading, temperature, time and reusability illustrated that these ceria impregnated NaZSM-5's were found to be selective, recyclable and could yield biodiesel at low temperature with low methanol to oil ratio due to the presence of both Lewis and Bronsted basicity. Hence, from the above study it is concluded that ceria impregnated ZSM-5 could be recognized as a potential catalysts for biodiesel production in industrial processes.

• 한국전기전자재료학회논문지
• /
• 제18권9호
• /
• pp.803-809
• /
• 2005

Cerium ammonium nitrate (CAN) and nitric acid was used an etchant and an additive for Ru etching and polishing. pH and Eh values of the CAN and nitric acid added chemical solution satisfied the Ru etching condition. The etch rate increased linearly as the concentration of CAN increased. Nitric acid added solution had the high etch rate. But micro roughness of etched surfaces was not changed before and after etching, The removal rate of Ru film was the highest in $1wt\%$ abrasive added slurry, and not increased despite the concentration of alumina abrasive increased to $5wt\%$. Even Ru film was polished by only CAN solution due to the friction. The highest removal rate of 120nm/min was obtained in 1 M nitric acid and $1wt\%$ alumina abrasive particles added slurry. The lowest micro roughness value was observed in this slurry after polishing. From the XPS analysis of etched Ru surface, oxide layer was founded on the etched Ru surface. Therefore, Ru was polished by chemical etching of CAN solution and oxide layer abrasion by abrasive particles. From the result of removal rate without abrasive particle, the etching of CAN solution is more dominant to the Ru CMP.