• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.9
• /
• pp.581-588
• /
• 2016

Piezoelectric thick films of a soft $Pb(Zr,Ti)O_3$ (PZT) based commercial material were produced by a conventional tape casting method. Thereafter, the interdigitated (IDT) Ag-Pd electrode pattern was printed on the $25{\mu}m$ thick piezoelectric film at room temperature. Co-firing of the 10-layer laminated piezoelectric thick films was conducted at $1,100^{\circ}C$ and $1,150^{\circ}C$ for 1 h, respectively. Piezoelectric cantilever energy harvesters were successfully fabricated using the IDT electrode pattern embedded piezoelectric laminates for 3-3 operation mode. Their energy harvesting characteristics were investigated with an excitation of 120 Hz and 1 g under various resistive loads (ranging from $10k{\Omega}$ to $200k{\Omega}$). A parabolic increase of voltage and a linear decrease of current were shown with an increase of resistive load for all the energy harvesters. In particular, a high output power of 3.64 mW at $100k{\Omega}$ was obtained from the energy harvester (sintered at $1,150^{\circ}C$).

• Journal of the Korean Ceramic Society
• /
• v.44 no.4 s.299
• /
• pp.202-207
• /
• 2007

High-Quality 1-Dimensional InN single crystalline have been grown by Halide Vapor-Phase Epitaxy on the Au catalyst coated Si substrate using the vapor-liquid-solid growth mechanism. We have been grown 1-dimension InN nanowires having controlled the growth conditions for substrate temperature and gases flow rate. The grown InN nanowire of characteristics for morphologies, crystal structure, and element analysis were carried out by SEM, HR-TEM, and EDS respectively. And the defects of InN crystalline were analyzed by indexing of selective area diffraction pattern with attached HR-TEM. We have successfully obtained the defect-free 1-dimensional InN single crystalline nanowire at the atmosphere pressure.

• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.441-446
• /
• 2009

Dense crack-free yttria film with 10 $\mu m$ thickness was prepared on aluminum by aerosol deposition. X-ray diffraction pattern on the film showed that it contained the same crystalline phase as the raw powder. Transmission electron microscopy revealed a nanostructured yttria film with grains smaller than 100 nm. Tensile adhesion strength between the film and aluminum substrate was 57.8 $\pm$ 6.3MPa. According to the etching test with $CF_4-O_2$ plasma, the etching rate of the yttria film was 1/100 that of quartz, 1/10 that of sintered alumina and comparable to that of sintered yttria.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.5
• /
• pp.256-262
• /
• 2017

Digital ink-jet printing technology using ceramic ink, which is thermally stable at high temperature above $1000^{\circ}C$, has an advantage of eco-friendly process applicable to manufacturing products with an excellent durability and various designs. Recently, replacement from conventional manufacturing process to digital process using ink-jet printing technique has been significantly accelerated in ceramic tile industry. In this study, we investigated ink-jet printability of ceramic ink on ceramic tile. Cyan, magenta, yellow, black ceramic inks, which are digital primary color of ink-jet printing, were printed on glazed surface of ceramic tiles, and their printabilities were comparatively analyzed. High temperature sintering process is generally required for manufacturing ceramic products, thus effect of sintering process on printed pattern of ceramic ink was also investigated by analyzing ink penetration depth and ink dot area.

• The Journal of Korean Academy of Prosthodontics
• /
• v.39 no.1
• /
• pp.14-24
• /
• 2001

The purpose of this study was to compare the fracture strengths and the fracture patterns of several hybrid-ceramic crowns and metal-ceramic crown. Ten crowns were constructed for each group according to the manufacturer's instruction. Removable template of silicone rubber impression material was used for standardization of each crowns. Each crown was cemented on a metal die with hybrid glass ionomer cement. All crowns cemented were stored in distilled water, $36^{\circ}C$ for 24 hours prior to loading in an universal testing machine. The load was directed at 130 degrees the long axis of metal die. The fracture strengths were measured and the fracture patterns were observed. The following results were obtained from this study 1. The mean fracture strengths of $Artglass^{(R)}$, $Sculpture^{(R)}$ and $Targis^{(R)}$ were $57.5{\pm}9.5Kgf,\;62.7{\pm}12.2Kgf$ and $60.2{\pm}10.1Kgf$ respectively. There was no significant difference among each hybrid ceramic crown group. 2. The toad required to fracture hybrid-ceramic crowns was significantly smaller than metal-ceramic crowns($131.7{\pm}22.0Kgf$). 3. In the metal-ceramic crowns, labial porcelain detached partially from porcelain-metal junction of proximal side by load. 4. Hybrid-ceramic crowns showed a simple fracture pattern that fracture line began at the loading area and extended through proximal surface, perpendicular to the margin. The crown was separated into two parts of labial side and lingual side. Above results revealed that three kinds of the hybrid-ceramic crowns used in this study must have careful application in clinical use since the strength of hybrid-ceramic crown was lower(about 1/2) than that of metal-ceramic crown.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.171-171
• /
• 2009

We have investigated the impact of coffee ring effect on the inkjet-printed $Al_2O_3$ thick films. In a single solvent system such as Dimethylformamide, the coffee-ring-pattern has appeared on the edge of sessile drop after evaporation. The peak-to-valley height difference in $Al_2O_3$ coffee ring is over 2um. This non-uniform deposition of $Al_2O_3$ over the surface leads to sever surface roughness of the inkjet-printed films. However, we have manipulated our printing parameters to improve the surface roughness and the packing density of the printed $Al_2O_3$ films. Our inkjet-printed $Al_2O_3$ films show 10 times smoother surface than the initially printed sample's surface. Also the packing density of the printed Ah03 film becomes 70% of high packed $Al_2O_3$. In this presentation, we would like to present the key process parameters of the inkjet printing process to overcome the genetic coffee ring problem.

• Applied Science and Convergence Technology
• /
• v.26 no.6
• /
• pp.184-188
• /
• 2017

Polymer deposition pattern on the ceramic lid surface is analyzed by numerical modeling. Assumption was made that is affected by gas flow pattern from the horizontal and vertical nozzles, temperature profile from the finger-like branches made of graphite and electrostatic potential effect. Calculated results showed gas flow dynamics is less relevant than two others. Temperature and electrostatic effects are likely determining the polymer deposition pattern based on our numerical simulation results.

• Journal of Multimedia Information System
• /
• v.7 no.2
• /
• pp.97-106
• /
• 2020

The subjective experience would degrade the current artificial artistic aesthetic analysis. Since Qiong kiln ceramics have a long history and occupy a very important position in ceramic arts, we employed computer-aided technologies to quickly automatically accurately and quantitatively process a large number of Qiong kiln ceramic images and generate the detailed statistical data. Because the color features are simple and significant visual characteristics, the color features of Qiong kiln ceramics are analyzed for the quantitative aesthetics. The Qiong kiln ceramic images are segmented with GrabCut algorithm. Three moments (1st-order, 2nd-order, and 3rd-order) are calculated in two typical color spaces, namely RGB and HSV. The discrimination powers of the color features are analyzed according to various dynasties (Tang Dynasty, Five Dynasties, Song Dynasty) and various utensils (Pot, kettle, bowl), which are helpful to the selection of the discriminant color features among various dynasties and utensils. This paper is helpful to promoting the quantitative aesthetic research of Qiong kiln ceramics and is also conducive to the research on the aesthetics of other ceramics.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.4 s.235
• /
• pp.504-511
• /
• 2005

The generation of fine relics of inorganic and metallic materials from precursor suspensions is of significant current interest as it holds the key to the fabrication of display and printed circuit board. Some novel printing methods depositing ceramic particles have been suggested in recent years. When a conducting liquid is supplied to a capillary nozzle at a low flow rate and when the interface between air and the liquid is charged to a sufficiently high electrical potential, the liquid meniscus takes the form of a stable cone, whose apex emits a microscopic jet. This is called as a cone-jet mode. In our experiments, an alumina particles flowing through a nozzle were subjected to electro-hydrodynamic printing in the cone-jet mode. The pattern of 'YONSEI' characters was tested at $10 {\mu}l/min$ of alumina ink flow rate and different applied voltages. At an applied voltage of 6 kV, feature size was in the range of $250 {\mu}m.$

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.192-192
• /
• 2009

We have successfully demonstrated the inkjet printing process to fabricate $Al_2O_3$ thick films without a high temperature sintering process. A single solvent system had a coffee ring pattern after printing of $Al_2O_3$ dot, line and area. In order to fabricate the smooth surface of $Al_2O_3$ thick film, we have introduced a co-solvent system which has nano-sized $Al_2O_3$ powders in the mixture of Ethylene glycol monomethyl ester and Di propylene glycol methyl ether. This co-solvent system approached a uniform and dense deposition of $Al_2O_3$ powders on the substrate. The packing density of inkjet-printed $Al_2O_3$ films is more than 70% which is very high compared to the value obtained from the films synthesized by other conventional methods such as casting processes. The characterization of the inkjet-printed $Al_2O_3$ films has been implemented to investigate its thickness and roughness. Also the dielectric loss of the films has been measured to understand the feasibility of its application to 3D integration package substrate.