• 한국유체기계학회 논문집
• /
• 제2권4호
• /
• pp.9-15
• /
• 1999

A screw-type centrifugal pump was manufactured to carry primarily solids and its impeller had a wide flow passage. However, there was an effect on the flow passage shape on delay of the choke due to entrained air not being clarified yet. Moreover, because its impeller has a particular shape, only few studies have tried to clarify the pump performance and details of internal flow pattern of that pump. For this reason, we carried out the pump performance experiment under air-water two-phase flow condition with different impeller tip clearances, pump rotational speeds and void fractions by using a small screw-type centrifugal pump designed to acquire basic data. In a general centrifugal pump, it was reported that there was a loss of pump head from single-phase flow to the choke due to air entrainment near the best efficiency point being large. However, the loss near the best efficient point in a screw-type centrifugal pump became less than that in a general centrifugal pump.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.43-48
• /
• 2004

A screw-type centrifugal pump was manufactured to carry solids primarily and its impeller has a wide flow passage. However, the effect of flow passage shape on delay of the choke due to entrained air has not been clarified yet. Moreover, because its impeller has a particular shape, only few studies have tried to clarify the pump performance and details of internal flow pattern of that pump. For that reason, we carried out the pump performance experiment under air-water two-phase flow condition with different impeller tip clearances, pump rotational speeds and void fractions by using a small screw-type centrifugal pump designed to acquire basic data. In a general centrifugal pump, it was reported that loss of pump head from single-phase flow to the choke due to air entrainment new the best efficiency point was large. However, the loss near the best efficient point in a screw-type centrifugal pump became less than that in a general centrifugal pump.

• 한국소음진동공학회논문집
• /
• 제14권9호
• /
• pp.785-791
• /
• 2004

The objective of this research is to suggest anoise prediction method for a centrifugal compressor. It is focused on the Blade Passing Frequency component which is regarded as the main part of the rotating impeller noise. Navier-Stokes solver is used to simulate the flow-field of the centrifugal compressor, and the time-dependent pressure data are calculated to perform the near-field noise prediction by using Ffowcs Williams - Hawkings formulation. Indirect Boundary Element Method is applied to consider the noise propagation effect. Pressure fluctuations of the inlet and the outlet in the centrifugal compressor impeller are presented and the sound pressure level prediction results are compared with the experimental data.

• 한국유체기계학회 논문집
• /
• 제16권6호
• /
• pp.26-31
• /
• 2013

Last blades of low-pressure turbine in nuclear power plant are the highly damaged part and always suffered from different types of loadings leading to various stress components, stresses due to centrifugal force and steam flow loading. Especially, centrifugal stress generated by turbine rotation is one of the main problems and more significant than other stresses as they have the greatest effect on total stress. Therefore, this study was performed to obtain the important information for estimation model development of the blade centrifugal stress level and distribution.

• 한국유체기계학회 논문집
• /
• 제16권4호
• /
• pp.28-34
• /
• 2013

Centrifugal pump consists of a axis, a impeller and a spiral casing. The impeller is the most important component in centrifugal pump. But to minimize flow loss in discharge passage including spiral casing, the shape of spiral casing is very important also. So, to investigate the effect of shape of the spiral casing on performance curve of pump, the characteristics of spiral casing were studied through numerical analysis for centrifugal pump used on industry field. From the results the rectangular model was showed more loss than the others because of asymmetric flow field.

• International Journal of Fluid Machinery and Systems
• /
• 제3권2호
• /
• pp.102-112
• /
• 2010

Artificial heart pumps have attracted the attention of researchers around the world as an alternative to the organ used in cardiac transplantation. Conventional centrifugal pumps are no longer considered suitable for long-term application because of the possibility of occurrence of blood leakage and thrombus formation around the shaft seal. To overcome this problem posed by the shaft seal in conventional centrifugal pumps, the magnetically suspended centrifugal pump has been developed; this is a sealless rotor pump, which can provide contact-free rotation of the impeller without leading to material wear. In Europe, clinical trials of this pump have been successfully performed, and these pumps are commercially available. One of the aims of our study is to numerically examine the internal flow and the effect of leakage flow through the gap between the impeller and the pump casing on the performance of the pump. The results show that the pressure head increases compared with the pump without a gap for all flow rates because of the leakage of the fluid through the gap. It was observed that the leakage flow rate in the pump is sufficiently large; further, no stagnant fluid or dead flow regions were observed in the pump. Therefore, the present pump can efficiently enhance the washout effect.

• 한국유체기계학회 논문집
• /
• 제4권1호
• /
• pp.30-37
• /
• 2001

The experimental study on the effect of axial clearance between the tip of impeller blades and stationary shroud has been performed. The investigated compressor, which is a part of a small auxiliary power unit engine, consists of a curved inlet, a centrifugal impeller, a channel diffuser and a plenum chamber. It was designed for a total pressure ratio of 4.3 and an efficiency of $77\%$ at design speed of 60,000 rpm. The experiments are carried out in an open-loop centrifugal compressor test rig driven by a turbine. For the four different clearance ratios Cr(clearance/impeller tip width) of 6.25, 10.93, 15.60 and 20.30 percent, the overall performance data are obtained at $97\%,\;90\%$ and $80\%$ of the design speed. The results show the overall pressure ratio decrease of $7.7\%$ and the efficiency loss of $8.7\%$ across the variation of clearance ratio near the design speed. It also indicates that the influence of tip clearance became weaker as the flow rate is reduced and the stable operating range is not significantly influenced by the change of clearance ratio.

• 한국환경과학회지
• /
• 제10권5호
• /
• pp.351-358
• /
• 2001

The main purpose of this study was to investigate the characteristics of cylindrical electrostatic precipitator with centrifugal effect in viewpoints of pressure drip and collection efficiency, experimentally. The experiment was carried out for the analysis of current-voltage, pressure drop and collection efficiency with various experimental parameters such as the applied voltage, inlet velocity, inlet size and inlet type(upper and bottom), etc. In the results, the pressure drops were estimated as 27~54, $34~63mmH_2O$ for inlet size $15mm{\tiems}30mm$ and $30mm{\tiems}60mm$, respectively. The collection effeciencies were shown over 90% with the small inlet size($15mm{\tiems}30mm$) for the applied voltage 40kV, inlet velocity(15~21m/s), and 51~89% with the large inlet size ($30mm{\tiems}60mm$). Moreover, in the applied voltage 0kV and inlet size $15mm{\tiems}30mm$, the collection efficiency induced by centrifugal force was represented as about 35% with inlet velocity 15 - 21m/s.

• 한국주조공학회지
• /
• 제28권3호
• /
• pp.113-118
• /
• 2008

A new approach of producing martensitic structure for guide-roll materials was developed using centrifugal casting instead of classic overlay welding process. Centrifugal casting offered a simpler process, fewer defects and even microstructures. Especially in terms of thermal fatigue cracking which usually occurs in the HAZ of welding beads of used continuous caster guide roll materials made by overlay welding process. A typical tensile strength of 1,600 MPa was obtained by this process and was higher than typical tensile strength($800{\sim}1,200\;MPa$) with overlay welding technique. Tempering at $400{\sim}550^{\circ}C$ for 2 hrs was observed to have significant precipitate hardening effect which increases strength and elongation. Nitrogen content from the Cr-N input in the casting process was found to have positive contribution to decrease the volume fraction of ${\delta}$-ferrite which directly corresponds to increasing strength of the roll materials.

• 대한치과기공학회지
• /
• 제7권1호
• /
• pp.5-12
• /
• 1985

This experimental study is perform to study the effect of the direction for the centrifugal force in operating centrifugal casting machine. In order to investigate the effect of direction for centrifugal force action on the casting ability 20 pieces of specimen are produced including one vertical direction and four horizontal directions. Casting shows us that the 15 pieces of specimen among them are included within $\pm$16. The results obtained through the comparison with 5 groups of the casting ability are as follows: 1. In the experiment of the casting, statistically significant difference are found between the vertical direction and the group of horizontal direction, namely, the direction of 3, 6, 9 and 12 o'clock, and also statistically there are significant differences between the direction of 9 o'clock and of 6 o'clock, and between the direction of 9 o'clock and of 12 o'clock which lie between the groups of horizontal directions. 2. The degree of casting ability is showing us on an average, 23.80 in the vertical direction. And also in the group of horizontal direction it prove in turn 15.60 in the direction of 9 o'clock, 14.47 of 3 o'clock, 13.30 of 12 o'clock, and 12.80 of 6 o'clock.