• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.175-176
• /
• 2023

The masonry structure is constructed by cement mortar binding material of brick objects and uses reinforced hardware(connected hardware or wall tie) together when building. However, over time, the corrosion of reinforced steel and the deterioration of joint mortar as well as bricks cause the risk of collapse. In particular, when the externally decorated brick wall is installed on the concrete girder for each floor, the angle bracket is not constructed or corroded, the full-layer weight load is applied to the wall of 0.5B, which is an example of full-scale or collapse. As a result of the evaluation, it was confirmed that the performance was improved compared to the existing bracket, and we plan to carry out a real-life test and long-term performance review of the building using the bracket in the future.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 가을 학술논문 발표대회
• /
• pp.105-106
• /
• 2021

This study examines the performance of CBS-Dust for the utilization of cement bricks as alkali stimulants for furnace slag replacement binders. It converts the CBS-Dust substitution rate and the excess slag substitution rate. According to the analysis, when replacing CBS-Dust with 65~70 % of BS substitution rate and 7.5~10 % of CBS-Dust, it shows excellent performance as an alkali stimulant of BS' potential hydrophobic reaction, and it is expected to be effective for secondary products of BS replaced in large quantities.

• 한국건설순환자원학회논문집
• /
• 제5권3호
• /
• pp.55-62
• /
• 2010

오늘날 각종폐기물 발생량이 증가되는데, 본 실험 연구에서는 미장 및 벽돌 제조용의 배합비를 적용하여 시멘트 모르타르의 하수슬러지 소각재의 폐기물을 이용하여 활용가능성에 대한 기초적 자료를 제시함이 본 연구의 목적이다. 실험에 따른 결과를 종합해 볼 때, 배합비 1:2의 하수슬러지 10%와 황토의 소량 첨가율과 배합비 1:7의 경우 압축강도가 다소 작지만 석분과 하수슬러지 10% ~ 20%를 첨가하면 하수슬러지를 재순환 할 수 있으며, 환경 친화적인 재료의 기초적 자료로 활용 가능할 것으로 판단된다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.453-458
• /
• 2001

This study was performed to reuse the dyeing wastewater sludge treated by Fenton process through the solidification/stabilization technique. To solidify the dyeing sludge the industrial by-products such as blast furnace slag, fly ash and waste sand with cement were used. The laboratory scale and pilot scale test were conducted at room temperature to make construction brick which has high compressive strength and low leaching of heavy metals. The experimental results showed that blast furnace slag and fly ash could be used instead of cement and the products satisfied the regulation of Korean Standards. The blast furnace slag increased the compressive strength and the optimum ratio of slag/dyeing sludge on dry basis was found 0.4. The solidifying agent of SB series could increase rapidly the compressive strength and the optimum ratio of solidifying agent/sludge on dry basis was 0.26 at which the strength was two times compared with non-added condition. The portion of waste and industrial by-products in matrix was over 80%. From the pilot test the optimum pressure in molding was 100kg/$\textrm{cm}^2$ at which the compressive strength was over 100kg/$\textrm{cm}^2$. And the strength increased continuously to 160kg/$\textrm{cm}^2$ until 120 days curing time due to pozzolanic reaction. When SB-20 as a solidifying agent was used, the unconfined compressive strength of dyeing sludge could be obtained 110kg/$\textrm{cm}^2$ which satisfied the regulation of cement brick in Korea Standard(KS).

• Earthquakes and Structures
• /
• 제5권4호
• /
• pp.477-497
• /
• 2013

This paper reports extensive experimental study done to compare workability and bond strength of five different types of polymer-based bonding agents for reinforcing bars in pinning retrofit. In pinning retrofit, steel pins of 6 to 10 mm diameters are inserted into holes drilled diagonally from mortar joints. This technique is superior to other techniques especially in retrofitting historic masonry constructions because it does not change the appearance of constructions. With an ordinary cement paste as bonding agent, it is very difficult to insert reinforcing bars at larger open times due to poor workability and very thin clearance available. Here, open time represents the time interval between the injection of bonding agent and the insertion of reinforcing bars. Use of polymer-cement paste (PCP), as bonding agent, is proposed in this study, with investigation on workability and bond strengths of various PCPs in brick masonry, at open times up to 10 minutes, which is unavoidable in practice. Corresponding nonlinear finite element models are developed to simulate the experimental observations. From the experimental and analytical study, the Styrene-Butadiene Rubber polymer-cement paste (SBR-PCP) with prior pretreatments of drilled holes showed strong bond with minimum strength variation at larger open times.

• 한국구조물진단유지관리공학회 논문집
• /
• 제15권4호
• /
• pp.87-98
• /
• 2011

최근 생태 친환경 건축이 화두로 등장하면서 친환경 건축재료인 점토벽돌과 공기의 흐름과 수분의 이동이 가능한 석회모르타르의 사용이 증가하고 있다. 하지만 국내 연구는 콘크리트벽돌과 시멘트모르타르에 집중되고 있어 점토벽돌 및 석회모르타르에 대한 연구가 거의 없는 실정이며, 조적조의 국내 기준 또한 국내에서 사용되는 재료와 다른 물리적 값을 사용하고 있는 국외기준을 바탕으로 제정되어 국내 실정을 적절히 반영하지 못하고 있다. 따라서 본 연구는 프리즘압축강도, 부착강도, 전단 및 사인 장강도 실험을 통해 점토벽돌과 석회모르타르를 사용한 조적구조의 물리적 특성을 파악하고자 한다. 또한, 콘크리트벽돌과 시멘트모르타르를 사용한 조적구조와의 물리적 특성을 비교분석하여 국내 조적기준을 개정하기 위한 근거를 제시하고자 한다. 점토 벽돌과 석회모르타르를 적용한 조적구조는 콘크리트벽돌과 시멘트모르타르를 사용한 조적구조와는 다른 양상을 보이므로 점토벽돌과 석회모르타르를 적용한 조적구조의 프리즘압축강도와 탄성계수에 대한 추정식을 제안한다.

• Advances in concrete construction
• /
• 제2권4호
• /
• pp.249-259
• /
• 2014

Mortar is a masonry product which is matrix of concrete. It consists of binder and fine aggregate and moreover, it is an essential associate in any reinforced structural construction. The strength of mortar is a special concern to the engineer because mortar is responsible to give protection in the outer part of the structure as well as at a brick joint in masonry wall system. The purpose of this research is to investigate the compressive strength and tensile strength of mortar, which are important mechanical properties, by replacing the cement and sand by stone dust. Moreover, to minimize the increasing demand of cement and sand, checking of appropriateness of stone dust as a construction material is necessary to ensure both solid waste minimization and recovery by exchanging stone dust with cement and sand. Stone dust passing by No. 200 sieve, is used as cement replacing material and retained by No. 100 sieve is used for sand replacement. Sand was replaced by stone dust of 15%, 20%, 25%, 30%, 35%, 40%, 45% and 50% by weight of sand while cement was replaced by stone dust of 3%, 5%, and 7% by weight of cement. Test result indicates that, compressive strength of specimen mix with 35% of sand replacing stone dust and 3% of cement replacing stone dust increases 21.33% and 22.76% respectively than the normal mortar specimen at 7 and 28 days while for tensile it increases up to 13.47%. At the end, optimum dose was selected and crack analysis as well as discussion also included.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.457-460
• /
• 2006

There are many kind of materials decorating outward of building such as paint, tile, brick, wood, stone and so on. But it has been pointed out some problems because of the industrial pollutions and wastes. Color concrete is a method of expressing out surface of exposed concrete. Generally, color concrete is manufactured by adding pigment to concrete. In this paper we used cement paste as a preparation step to apply to concrete. Pigment was added to white cement for easy observance of color difference. And color change was measured by color reader. Finally, we can predict color difference according to amount of pigment. Also, we investigate the color concrete technology for Art type using developed color concrete.

• KIEAE Journal
• /
• 제3권2호
• /
• pp.37-44
• /
• 2003

The aim of this study was to analyze the thermal performance through Test-Cell of TI-wall in domestic climate. This study was carried out as follows: 1) The TI-wall was studied for ability to reduce heat loss through the building envelope and analyzed to TIM properties. 2) Test models of TI-wall were designed through the investigation of previous paper and work, measured for winter and spring, and the thermal effects were analyzed. The type of the TIM used in test model is small-celled(diameter 4mm and thickness 50mm) capillary and cement brick(density $1500kg/m^3$) was used by thermal mass. 3) Test-cell of TI-wall was calibrated from measured data and the dynamic simulation program ESP-r 9.0. In these simulations, the measured climate conditions of TaeJon were used as outdoor conditions, and the simulation model of Test-cell was developed. 4) The sensitivity analysis is executed in various aspects with standard weather files and ESP-r 9.0, and then most suitable system of TI-wall are predicted. Finally, The suitable system of TI-wall was analysed according to sizes of air gap, kinds, thickness, and the surface absorption of therm wall. The result is following. In TI-wall, Concrete is better than cement brick, at that time the surface absorption is 95%, and the most efficient thickness is 250mm. As smaller of a air gap, as reducer of convection heat loss, it is efficient for heating energy. However, ensuring of a air gap at least more than 50mm is desirable for natural ventilation in Summer.

• 한국광물학회지
• /
• 제31권3호
• /
• pp.149-159
• /
• 2018

안산암을 벽돌 모양으로 다듬어 쌓아 올린 경주 분황사 모전석탑은 현재 남아있는 가장 오래된 신라시대 석탑이다. 석탑에서 나타나는 손상양상은 백색피각, 흑색피각, 변색, 토양흡착 등의 오염물, 생물서식, 보수물질 등이다. 구조적 요인에 의한 손상양상으로 배부름 현상이 나타난다. X-선 회절분석 결과에 의하면 백색피각의 주 구성광물은 방해석($CaCO_3$)과 서모나트라이트($Na_2CO_3{\cdot}H_2O$)로 자연 상태에서 쉽게 나타나는 증발잔류광물이다. 석탑에 나타나는 손상양상은 각 부위별로 상당히 다르다. 생물서식은 기단, 사자상, 1층과 2층의 옥개석에서, 보수물질은 기단에서 확인된다. 배부름 현상은 1층 탑신에서 나타난다. 전체적인 손상 유형별 점유율은 생물서식, 오염물, 보수물질이며 그외 배부름 현상, 박리 순으로 높게 나타났다. 가장 높은 점유율을 보인 개별 손상양상은 흑색미생물(39.3%)이며, 다음은 지의류(17.9%), 변색(8.0%), 백색피각(5.5%), 시멘트 모르타르(5.1%), 배부름 현상(3.9%), 박리(3.1%) 순으로 나타났다.